Outdoor 300Mbps Wireless N Access Point - 2T2R 5GHz R300WN22OP5 / R300WN22OP5G / R300WN22OP5E *actual product may vary from photos DE: Bedienungsanleitung - de.startech.com FR: Guide de l'utilisateur - fr.startech.com ES: Guía del usuario - es.startech.com IT: Guida per l'uso - it.startech.com NL: Gebruiksaanwijzing - nl.startech.com PT: Guia do usuário - pt.startech.com For the most up-to-date information, please visit: www.startech.
FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Table of Contents Introduction.............................................................................................2 Packaging Contents.................................................................................................................................. 2 System Requirements............................................................................................................................... 2 Product Overview......................................................................
Introduction Packaging Contents • 1 x Outdoor Access Point • 1 x PoE Injector • 1 x Metal Hose Clamp • 1 x Power Adapter • 1 x Instruction Manual System Requirements • A networked computer system with a Java-enabled web browser (for configuration) • Cat 5 (or better) network cabling from PoE Injector to Wireless AP and PoE Injector to LAN Switch/router (no more than 100m total) • Mounting screws / anchors for wall mounting PoE Injector and/or Wireless AP Instruction Manual 2
Product Overview Rear View LED Panel Pole/Wall Mount Bracket Interface Cover Instruction Manual 3
Connection Ports LAN 1 Ground LAN 2 Reset Button Interface Description Reset Button Press continually for 5 ~ 10 seconds to reset the device to factory defaults LAN 1 Allows LAN connection through a Category 5 (or better) cable. Supports auto-sensing for 10/100Mbps speeds and half/ full duplex LAN 2 Allows LAN connection through a Category 5 (or better) cable.
LED Indicators Indicator PWR LAN 2 LAN 1 Wifi Activity Indicators State Description ON The device is powered on OFF The device is powered off ON Link detected OFF No link detected Flashing Data is being transmitted / received on the LAN 2 interface ON Link detected OFF No link detected Flashing Data is being transmitted / received on the LAN 1 interface ON Wireless client(s) are connected.
Hardware Installation 1. Connect the included power adapter to an available wall outlet and the DC jack on the PoE injector. 2. Connect an Ethernet cable from the LAN port of the PoE Injector to your LAN switch or router. 3. Connect a second Ethernet cable from the PoE port of the PoE Injector, the other end of this cable will connect to the AP as instructed in the following steps. 4. Slide the bottom cover of the unit down to remove it and expose the ports. 5.
1. Configure a system to be on the same LAN as the AP (192.168.1.xxx, where xxx is 1 – 254, except 200 ). 2. Open a web browser and enter the IP address 192.168.1.200 into the address bar, then press Enter. 3. Enter the default username / password (admin / admin) and press Enter. 4. Click on the Operation Mode link from the left column to select your desired Network and IP Mode as applicable to your network (described below). Then click the Apply button.
Network Mode IP Mode Description Bridged N/A Disables Network Address Translation (NAT) and bridges the Wireless AP and LAN ports together Static Wireless ISP DHCP PPPoE Connects to an external wireless network (Wireless ISP) and rebroadcasts as an internal wireless network (WLAN). *See Wireless ISP section below for instructions on this mode Note: Depending on the modes you choose, applicable settings will be enabled/ disabled automatically. 5.
7. Once you have configured the Basic Settings, select Security Settings from the left column and choose your desired encryption type and security key. Then click the Save button. 8. To restrict access to the web interface of your AP, it is also recommended to configure a password, which can be done by selecting Maintenance from the left column of the web interface. Then click the Apply button to reboot the device and apply all changes made in previous steps.
Wireless ISP (WISP) Mode When using the AP in Wireless ISP mode, settings should be configured as follows. 1. Select Network and then Operation Mode from the left column of the web interface. 2. Set your Network Mode to “Wireless ISP”, and then click the Apply button. 3. Select LAN Setup from the left column and change the DHCP Server option to “Enable”, configure your desired DHCP range settings, and then click the Save button. 4.
7. Once complete, click the Apply button to reboot the AP and put all modified settings into effect.
Specifications Supported Wireless Standards IEEE802.11 a/n Chipset Atheros - AR9344 Connectors 2 x RJ45 Ethernet Female Antenna Configuration 2x2:2 (TxR:s) Antenna Type 14dBi Dual Polarization Directional Antenna Wireless Frequency Range 5.150GHz ~ 5.850GHz Wireless Bandwidth 20/40MHz 64/128 bit WEP WPA(TKIP with IEEE 802.1x) Wireless Encryption Supported WPA2(AES with IEEE 802.1x) WPA -PSK Maximum Wireless Distance 3km* 802.11n : (40MHz) : up to 300Mbps Maximum Data Transfer Rate 802.
Technical Support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. For the latest drivers/software, please visit www.startech.com/downloads Warranty Information This product is backed by a two year warranty. In addition, StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
