RACKCOND1701 Instruction Manual Folding Rackmount Console 1U 17” High Resolution Dual Rail Rack Mount LCD Console Drawer Manual Revision:12/16/2010 For the most up-to-date information, please visit www.startech.
FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Table of Contents Introduction............................................................................................................ 1 Packaging Contents.........................................................................................................................1 Installation.............................................................................................................. 1 Hardware Installation/Assembly..........................................................................
Introduction Packaging Contents • • • • • • 1 x 1U LCD Rack Console 1 x KVM Module 2 x KVM Module Extension Bracket 2 x Rear Bracket 1 x Universal Power Adapter 1 x Instruction Manual Installation Hardware Installation/Assembly 1. Note the safety stopper on the console drawer. The safety stopper is designed to prevent the drawer from sliding out during transportation. Do not remove until the console has been properly installed. 2.
3. The rear brackets, and slide rails have a tight fit. Carefully slide the rear brackets into the front rails, then fasten the brackets to the cabinet/rack posts. 4. Attach the extensions brackets to both sides of the KVM switch module. Please note the length of the extensions and mount them as shown. NOTE: The orientation of the wide side of the extension 5. Push the KVM switch module evenly toward the drawer: 6.
7. Remove the safety stoppers on both sides of the rack console by unfastening the small screws. Please note that once the Safety Stopper is removed, the drawer is free to slide out when the console is tilted. Be cautious, as this could cause injury. Ensure the console is properly installed before removing the safely stoppers. 8. Slide the console out slightly until the stoppers along the sides are accessible. Remove the stopper by unfastening the small screws holding it in place. 9.
Please note: You can only connect to a computer using either the PS/2 or USB port not both simultaneously. Connecting to a USB Controlled Computer Connect the standard VGA cable and a USB A-B cable to the computer and KVM Module as shown below. The computer can be a USB-ready PC, Sun, HP server, or a Mac. Connecting to a PS/2 Controlled Computer Connect the standard VGA cable and two mini-DIN6 male-to-male cables to the computer and KVM Module as shown below.
Operation Front Panel Controls KVM Control and Status: (This section is effective only when a multi-port KVM switch module, not included, is connected.) • Computer Selection Buttons - Press one of these push buttons to select a computer. For 16 port models, 1~8 represent the lower 8 ports, while A~H indicates the higher 8 ports. Port 1 and A share the same push button; if port 1 is already selected, tap its push button to select port A.
Alternative Input Devices In addition to the built-in keyboard and touchpad, this rack console also supports using an external keyboards and mouse, including wireless (cordless) keyboards and mice. A USB port is accessible on the rack console that allow for connecting input devices, as well as controls that can disable the touchpad in favour of an external mouse. The USB port is hidden under the removable cover located in the upper right hand corner of the keyboard tray.
Keyboard Replacement The keyboard is replaceable in the event of language changes or maintenance. To replace the keyboard, pull out the keyboard tray, and remove 6 screws from the underside of the tray. There is a small hole on the bottom of the tray as well, that can be used to lift the keyboard out of the tray. Tilt the keyboard up, locate the mini-USB cable underneath the keyboard and unplug it gently.
Touchpad Replacement The built-on Touchpad offers “wheel mouse” functionality. The area of the Touch Pad to the right side of the two small triangular marks is the simulated “wheel” as shown below: With the keyboard removed, to remove the Touch Pad, pull the small tab underneath it upward to release the latch (1). Slide the touchpad unit forwards (2) until the Touch Pad can be lifted up clear from the notches, as shown in the figure below (3). The Touchpad is connected by a mini-USB cable.
Specifications Display Size Panel Type Maximum Screen Resolution Supported Colors Response Time Back Lighting Contrast Ratio Brightness Pixel Pitch 17.3” Active Matrix TFT LCD 1920x1080 (60/70/75 Hz) 262K (RGB 6-bit) 8ms LED 500:1 300 cd/m2 0.199mm x 0.199mm Horizontal: -70 ~ 70 Vertical: -60 ~ 60 105-key USB keyboard with touchpad 1 x DE-15 VGA female 1 x USB type B female 2 x PS/2 female 2 x USB type A female 100 ~ 240 VAC 13.2 W Heavy duty steel 600mm (23.6in) / 1150mm (45.
Technical Support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industryleading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. Warranty Information This product is backed by a one year warranty. In addition, StarTech.
StarTech.com has been making “hard-to-find easy” since 1985, providing high quality solutions to a diverse IT and A/V customer base that spans many channels, including government, education and industrial facilities to name just a few. We offer an unmatched selection of computer parts, cables, A/V products, KVM and Server Management solutions, serving a worldwide market through our locations in the United States, Canada, the United Kingdom and Taiwan. Visit www.startech.
