3.5in eSATA USB Black SATA External Hard Drive Enclosure SAT3510BU2E SAT3510BUEGB SAT3510BUEEU *actual product may vary from photos DE: Bedienungsanleitung - de.startech.com FR: Guide de l'utilisateur - fr.startech.com ES: Guía del usuario - es.startech.com IT: Guida per l'uso - it.startech.com NL: Gebruiksaanwijzing - nl.startech.com PT: Guia do usuário - pt.startech.com For the most up-to-date information, please visit: www.startech.
FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Table of Contents Introduction ............................................................................................1 Features......................................................................................................................................................... 1 Package Contents...................................................................................................................................... 1 Hardware Guide.......................................................
Introduction Thank you for purchasing a StarTech.com InfoSafe 3.5” eSATA/USB 2.0 Removable SATA HD Enclosure. Supporting the latest generation of hard drive storage (up to 1TB SATA hard drives), this enclosure allows the use of any 3.5” SATA II (SATA /300) or SATA (SATA /150) and can be connected to a host computer using either eSATA or USB.
Hardware Guide Rear Panel Power Button DC Power Adapter Input USB Output eSATA Output Fan Hardware Installation Inserting a Hard Drive 1. Unlock the keylock situated on the front of the SAT3510BU2E.
2. Lift the handle on the front panel and pull the front panel door out from the body (as shown below). 3. Place the hard drive into the SAT3510BU2E, SAT3510BUEGB, SAT3510BUEEU. The printed label on the hard drive should be on the right hand side, with the SATA connector on the lower half of the drive. 4. Push the door to slide the hard drive into place. Do not push the hard drive into the enclosure by hand, otherwise it may not be properly installed. 5.
Removing a Hard Drive 1. Unlock the key lock. 2. Lift the handle on the front panel and pull the front panel door out from the body. 3. Carefully remove the hard drive from the enclosure.
4. Close the door. It is suggested that you lock the key lock. Recognizing the Hard Drive Windows XP USB 2.0 If you are using the USB 2.0 interface to connect the hard drive to your computer, no setup is required. Simply plug the hard drive into an available USB port and turn the power on to the SAT3510BU2E. When you open My Computer the drive should be visible under the heading Devices with Removable Storage.
1. Right-click My Computer and click Manage. 2. In the left pane, select Device Manager. 3. In the Device Manager window, click the “+” next to Disk Drives. Since the drive was not powered on during the boot up process, it should not yet be visible. 4. Turn on the SAT3510BU2E, SAT3510BUEGB, SAT3510BUEEU. Once the power indicator is illuminated, click the Scan button. 5. The Device Manager will scan for plug and play hardware.
Windows Vista™ / 7 USB 2.0 If you are using the USB 2.0 interface to connect the hard drive to your computer, no setup is required. Simply plug the hard drive into an available USB port and turn the power on to the SAT3510BU2E, SAT3510BUEGB, SAT3510BUEEU. Open My Computer and the drive should be visible under the heading “Devices with Removable Storage.” eSATA If you are using the eSATA interface to connect the hard drive to your computer, there are two setup processes you can follow.
2. In the left pane of the Computer Management window, select “Device Manager.” 3. Turn on the SAT3510BU2E. Once the power indicator is illuminated, click the “Scan” button. Scan button 4. The Device Manager will begin an installation of the necessary driver software. Once it has completed the scan, your drive should be visible below the Disk Drives heading. Safe Drive Removal Ensure that any programs that have accessed the drive are closed.
Specifications SAT3510BU2E / SAT3510BUEGB / SAT3510BUEEU 1 x eSATA Plug 1 x USB B Female Connector Types Chipset INIC 1611 Data Transfer Rate 3Gb/s (eSATA) 480Mbps (USB 2.0) Drive Capacity Support Up to 1 TB Drive Type Compatibility SATA 300 (SATA II) SATA 150 (SATA I) O/S Compatibility Windows 98SE, ME, 2000 XP, Vista™, 7 Mac OS 8.6, 10.
Technical Support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. For the latest drivers/software, please visit www.startech.com/downloads Warranty Information This product is backed by a two year warranty. In addition, StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.