UNI3510U2E / UNI3510U2EGB UNI3510U2EB / UNI3510UEBGB Instruction Manual 3.5” External Hard Drive Enclosure 3.5” eSATA/USB 2.0 to IDE/SATA External Hard Drive Enclosure with One-Touch Backup Manual Revision:06/17/2010 For the most up-to-date information, please visit www.startech.
FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Table of Contents Introduction...................................................................... 1 Packaging Contents.....................................................................1 System Requirements..................................................................1 Hardware Guide................................................................ 2 Front Panel...................................................................................2 Rear Panel.............................................
Introduction This enclosure lets you turn almost any high capacity 3.5” Serial ATA (SATA) or IDE hard drive into an eSATA (SATA only) or USB (SATA or IDE) external hard drive, allowing you to customize your external storage solution based on your preference of hard drive model and manufacturer.
Hardware Guide Front Panel 1 2 1. Power Button/LED 2. Backup Button Rear Panel 1 1. DC In Port 2 2. eSATA Port 3 3. Mini USB Port 4.
Installation Hardware Installation 1. Open the hard drive enclosure by pushing the rear panel release button to the right and sliding the hard drive bracket out of the external casing from the front. 2. If using an IDE/ATA hard drive, ensure that the hard drive you are using is set to MASTER. 3. Pull the two tabs on either side of the hard drive holding mechanism up, then connect the provided SATA or IDE data and power supply cables to the rear ports of the drive. 4.
CN6 J1 CN5 CN1 IDE HDD: Only the USB 2.0 interface is available for connecting an IDE hard drive to the host computer. Plug the 40-pin IDE data cable into the port labelled CN1 on the enclosure’s PCB board. Plug the included 4-pin SP4 to LP4 power adapter cable into the J1 connector. 5. To mount the hard drive, place it into the holding tray and press the tabs on either side down to secure the drive in the enclosure. 6.
1. Insert the Drivers CD into your computer’s CD-ROM. Open the DRIVERS.exe application to begin the installation process. 2. Once the installer is running, there are a number of options available to you from the DRIVERS.exe home screen. To install the backup software, click Install Backup Program under the heading that corresponds with your drive-type (IDE or SATA). 3. The PCClone EX Lite Installer window will appear. Click Install to proceed with the installation process. 4.
5. Click Browse to designate the directory in which the software will be installed. Once you have made your selection, click Install to continue. 6. The installation will now take place. Once the installation is complete, you may exit the DRIVERS.exe application. Recognizing the Hard Drive Windows XP USB 2.0 If you are using the USB 2.0 interface to connect the hard drive enclosure to your computer, no setup is required.
eSATA If you are using the eSATA interface to connect the hard drive enclosure to your computer, there are two setup processes you can follow. If the hard drive enclosure is powered on upon booting up the computer, it will automatically detect the drive. Otherwise, if you connect and power on the hard drive enclosure once the computer has already been booted up, you will need to open the Device Manager to scan for it.
eSATA If you are using the eSATA interface to connect the hard drive enclosure to your computer, there are two setup processes you can follow. If the hard drive enclosure is powered on upon booting up the computer, it will automatically detect the drive. Otherwise, if you connect and power on the hard drive enclosure once the computer has already been booted up, you will need to open the Device Manager to scan for it.
Specifications SATA 3.0Gb/s Bus Interface USB 2.0 Chipset ID JMicron JMB20337 1 x eSATA connector* External Connectors 1 x USB Mini B connector 1 x DC Power connector 2 x SATA 7-pin 1 x SATA Power 15-pin Internal Connectors 1 x 40-pin IDE/ATA 1 x LP4 Power 4-pin 3.0 Gb/s (eSATA) Maximum Data Transfer Rate 480 Mb/s (USB 2.0) Fans 1 x 80mm Power Adapter 12VDC, 2000mA, type M plug Enclosure Material Aluminum Operating System Support Windows® 2000/XP/Vista/Server 2008 R2/7, Mac OS® 9.x/10.
Technical Support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. Warranty Information This product is backed by a one year warranty. In addition, StarTech.
StarTech.com has been making “hard-to-find easy” since 1985, providing high quality solutions to a diverse IT and A/V customer base that spans many channels, including government, education and industrial facilities to name just a few. We offer an unmatched selection of computer parts, cables, A/V products, KVM and Server Management solutions, serving a worldwide market through our locations in the United States, Canada, the United Kingdom and Taiwan. Visit www.startech.
