HDMI® over Cat 5e/6 Extender - 50m ST121SHD50 *actual product may vary from photos DE: Bedienungsanleitung - de.startech.com FR: Guide de l'utilisateur - fr.startech.com ES: Guía del usuario - es.startech.com IT: Guida per l'uso - it.startech.com NL: Gebruiksaanwijzing - nl.startech.com PT: Guia do usuário - pt.startech.com For the most up-to-date information, please visit: www.startech.
FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Table of Contents Product Diagram.....................................................................................1 Top View........................................................................................................................................................ 1 Rear View....................................................................................................................................................... 1 Front View........................................................
Product Diagram Top View 1 1 2 2 1. LED Indicator 1. LED Indicator 2. EDID Copy Button 2. EQ Selector Rear View 1 2 1 1. Power Jack 1. Power Jack 2. HDMI In 2. HDMI Out 2 Front View 2 1 1. LINK OUT A (RJ-45 Connector) 2 1 1. LINK IN A (RJ-45 Connector) 2. LINK OUT B (RJ-45 Connector) 2.
Introduction The ST121SHD50 HDMI® over CAT5e/6 Video Extender kit lets you extend HDMI® video and audio up to 165 feet (50 Meters)(1080i) over 2 CAT5e Ethernet cables, or up to 130 Feet (40 Meters)(1080p) over 2 CAT6 Ethernet cables. For added versatility both the Transmitter and Receiver can be powered by the same single power source using Power Over Cable (POC).
LED Indicator Status Transmitter DVI EDID content configured *Emit blue with green flashing twice HDMI EDID content configured *Emit blue with green flashing three times HDCP syncing **Purple Status Receiver Video Linking ***Steady Blue Video unlinking Steady Red *It is suggested replacing cables with better quality ones if the LED emits blue without video displaying. **The emitting period of purple LED depends on connected device.
Installation Preparing Your Site 1. Determine where the local video source (i.e. computer, Blu-ray Player) will be located and set up the device. 2. Determine where the remote display will be located and place/ mount the display appropriately. NOTE: This HDMI® extender kit features Power over cable, allowing both the Transmitter and Receiver to be powered from a single power source that can be connected at either end of the connection.
c) Connect the other end of the Cat5e/6 cable (from LINK OUT A) to the LINK IN A (RJ-45 connector) on the Receiver Unit. d) Connect the other end of the Cat5e/6 cable (from LINK OUT B) to the LINK IN B (RJ-45 connector) on the Receiver Unit. NOTE: If using Cat6 cables, extension distance is limited to 40m (130 ft) 3. Install Receiver Unit a) Position the Receiver Unit near the video display (i.e. television, projector). b) Connect the video source to the HDMI® OUT on the Receiver Unit using an HDMI® cable.
The following is the test result while using different types of CATx cables Cable Type CAT6 CAT5 (solid) CAT5 (stranded) Resolution Cable Length (max.) 1080i 50M 1080p 40M 1080i 50M 1080p 20M 1080i 40M 1080p 16M EDID Configuration In some cases display problems may occur due to incorrect EDID communication between the display monitor and the unit or inappropriate EDID data programmed by display manufactures.
EDID Factory Default Setting To avoid confusion in which EDID information has been copied or for more purposes, this function enables to reset the state to factory default. Step 1. Use CATx cable for connection between Tx & Rx on Aux RJ-45 Jack. Apply power to Receiver Unit. Step 2. Press the button “EDID Copy” and release the button RIGHT AFTER the LED flashes red. Step 3. The LED flashes green & red indicating default setting successfully. DDC Pass Mode Press the button for more than 15 sec.
Specifications AV Input HDMI® AV Output HDMI® Cabling Cat 5e/6 UTP Audio Yes Local Unit Connectors 1x HDMI® (19 pin) Female 2x RJ-45 Female Remote Unit Connectors 1x HDMI® (19 pin) Female 2x RJ-45 Female Maximum Data Transfer Rate HDMI® - 1.656Gbps Max Distance 50 m / 165 ft(1080i) Maximum Digital Resolutions 1080p @ 60Hz, 24-bit Wide Screen Supported Yes Audio Specifications Supports Dolby® TrueHD, DTS-HD MA Input Voltage 110 ~ 240V AC Input Current 0.
Technical Support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. For the latest drivers/software, please visit www.startech.com/downloads Warranty Information This product is backed by a two year warranty. In addition, StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
