Mobile Projector Cart - Height Adjustable Actual product may vary from photos User Manual SKU#: ADJPROJCART For the latest information and specifications visit www.startech.
Compliance Statements Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.
Safety Statements Safety Measures • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines. Mesures de sécurité • L’installation et/ou le montage du produit doit être réalisé par un professionnel certifié et dans le respect des normes locales et du code de construction local.
Warning Statements • Assemble this product according to the instructions. • Read the entire manual and ensure the instructions are fully understood before assembling and/or using this product. • Do not exceed the weight capacity of this product. Overloading this product might result in injury or property damage. • Weight capacity: 10 kg (22 lb.) per platform. • Do not allow children to climb on this product, or use this product without proper supervision.
du lägger till. • Se till att all utrustning är korrekt installerad innan du börjar justera produkten. • Flytta inte vagnen över kablar eller ojämna ytor. • Innan du börjar flytta på vagnen, se till att hjulen är upplåsta. Waarschuwingen • Zorg dat u dit product volgens de instructies in elkaar zet. • Lees de gehele handleiding en zorg dat u de instructies begrijpt voordat u dit product in elkaar zet en gebruikt. • Overschrijd de maximale capaciteit van dit product niet.
• 本製品を組み立てる際、ネジを締めすぎないようにして下さい。ネジを締め ているうちに手応えを感じたら、締めるのを止めてください。 • 本製品は、二人がかりでの組み立てを想定しています。手助けなしに単独で 組み立てと設置を行わないで下さい。 • 本製品に装置を積載する前に、組み立てと設置が適切に行われたか確認し て下さい。 また、積載する装置の重量に本製品が対応しているか確認して 下さい。 • 転倒注意！モニタが一番高い位置にある状態でカートを動かさないで下さ い。 また、モニタを押してカートを動かすのはやめて下さい。 • コードやケーブルの上、 または凹凸のある床面でカートを移動させないで 下さい。 Dichiarazioni di avvertenza • Assicurarsi di Assemblare il prodotto secondo le istruzioni.
Avertissements • Assemblez ce produit conformément aux instructions. • Lisez tout le manuel et assurez-vous que vous comprenez les instructions avant de commencer à assembler et utiliser ce produit. • Ne dépassez pas la capacité pondérale du produit. Une surcharge du produit peut entraîner des blessures ou des dommages matériels. • Capacité de poids : 10 kg par étagère • N’autorisez pas les enfants à grimper sur ce produit ni à l’utiliser sans surveillance.
• Antes de adicionar o equipamento a este produto, certifique-se de que o montou e instalou devidamente e de que o produto pode suportar o peso do equipamento que está a adicionar ao mesmo. • Certifique-se de que instala devidamente todo o seu equipamento antes de começar a ajustar este produto. • Não mova o carro pelos fios, cabos ou superfícies irregulares. • Antes de começar a mover o carro, certifique-se de que desbloqueia os rodízios.
Warnhinweise • Beachten Sie bei der Montage dieses Produkts die Montageanweisungen. • Bevor Sie dieses Produkt montieren und verwenden, lesen Sie das gesamte Handbuch und vergewissern Sie sich, dass Sie die Anweisungen verstanden haben. • Überschreiten Sie nicht die Tragkraft dieses Produkts. Ein Überladen dieses Produkts kann zu Verletzungen oder zur Beschädigung des Produkts führen.
Table of Contents Compliance Statements.........................................................................i Safety Statements...................................................................................ii Warning Statements...............................................................................iii Product Diagram.....................................................................................1 Front Angle View............................................................................
Product Diagram Front Angle View Projector Platform Laptop Platform Knobs Support Pole Base Cross Member Base Feet Casters To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Product Dimensions Front Angle View To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Product Information Package Contents Projector Platform Qty: 1 Base Feet Qty: 2 Laptop Platform Knobs Support Pole Qty: 1 Qty: 3 Qty: 1 Base Cross Member Cable Clips Type One Washers Qty: 2 Qty: 1 Type Two Washer Nuts Qty: 1 Qty: 8 Casters without Brakes Qty: 9 Casters with Brakes 2 visit www.startech.
M6 x 65mm Bolts Qty: 5 M6 x 50 mm Screws Qty: 2 M6 x 12 mm Screws M6 x 30 mm Screws Qty: 4 Qty: 2 Wrench Hex Key Qty: 1 Qty: 1 User Manual Qty: 1 4 M6 x 50 mm Button Head Screws Qty: 3 Mounting Brackets Qty: 2
Technical Specifications Type of Measurement Measurement Weight Capacity Up to 22 lb. (10 kg) per platform Tilt Range +12° ~ -12° Requirements For the latest requirements, please visit www.startech.com/ADJPROJCART • Laptop x 1 • Projector x 1 • Phillips Head Screwdriver x 1 To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Installation Attach the Base Base Cross Member Base Foot Figure 1 1. Flip the Base Cross Member and both Base Feet upside down and place onto a clean and flat surface. (Figure 1) Note: Cover hard floors with a soft cloth to prevent scratching. 2. Place one of the Base Feet into one of the grooves in the Base Cross Member. Align the holes in the sides of the Base Foot with the holes in the sides of the Base Cross Member. 3.
Attach the Casters Wrench Caster Figure 2 1. Thread the two Casters with Brakes into the holes, located in the bottom of the Base Feet and tighten, using the Wrench. (Figure 2) 2. Insert the two Casters without Brakes into the holes on the other side of the Base Feet and tighten, using the Wrench. 3. Flip the Base upright so that the Casters are making contact with the surface. Note: For uneven surfaces, adjust the position of the Nut on each Caster.
Attach the Support Pole Hex Key Type One Washer Support Pole Wrench Nut M6 x 12 mm Screws Figure 4 M6 x 65 mm Bolt Figure 3 1. Slide the connecting end of the Support Pole over the center of the Base Cross Member. Align the holes in the Support Pole with the holes in the Base Cross Member. (Figure 3) 2. Insert the four M6 x 12 mm Screws through the four holes in the top of the connecting end of the Support Pole and into the Base Cross Member. 3.
4. Slide one M6 x 65mm Bolt through the square shaped holes located in the sides of the connecting end of the Support Pole. (Figure 4) 5. Slide one Type One Washer onto the M6 x 65mm Bolt. 6. Thread one Nut onto the M6 x 65mm Bolt and tighten, using Wrench. Attach the Laptop Platform Laptop Platform Phillips Head Screwdriver Support Pole M6 x 30 mm Screw Type One Washer Nut Wrench Figure 5 1. Place the Laptop Platform onto the ledge located on the side of the Support Pole.
2. Insert one M6 x 30 mm Screw through the hole in the top of the Laptop Platform and into the ledge portion of the Support Pole. 3. Slide one Type One Washer onto the M6 x 30 mm Screw. 4. Thread one Nut onto the M6 x 30 mm Screw and tighten by holding the Nut with the Wrench and by fastening the M6 x 30 mm Screw, using an appropriate size Phillips Head Screwdriver. Note: Two people may be required to complete the step 5. Repeat steps 2-4 for the second M6 x 30 mm Screw.
1. Determine the desired height setting for the Projector Platform. The Projector Platform can be adjusted from 37.4” (950 mm) to 57” (1450 mm) in pre-set increments. 2. Extend the inner portion of the Support Pole to the desired height setting. 3. Insert two M6 x 50 mm Button Head Screws through the two holes located in the outer portion of the Support Pole. (Figure 6) 4. Thread one Knob onto each one of the M6 x 50 mm Button Head Screws and hand tighten. Note: Do not overtighten the Knobs.
• Align the holes in the Mounting Brackets with the holes in the Support Pole and hold in place until the Screws are installed in the following steps. Attach the Projector Platform Type One Hex Key Washers Wrench M6 x 50 mm Screw Knob M6 x 50 mm Button Head Screw Figure 8 1. Slide the Projector Platform over the Mounting Brackets. Align the holes in the in the Projector Platform with the holes in the Mounting Brackets. (Figure 8) 2. Slide one Type One Washer over one M6 x 50 mm Screw. 3.
6. Slide one Type Two Washer over one M6 x 50 mm Button Head Screw. 7. Insert the M6 x 50 mm Button Head Screw through the lower hole in the Projector Platform. 8. Thread one Knob onto the M6 x 50 mm Button Head Screw and hand tighten. Operation Move the Mobile Projector Cart 1. (Optional) Disconnect and remove any Cables connecting the Mobile Projector Cart to the wall. 2. Secure the Projector and Laptop to the Mobile Projector Cart. 3. Disengage the Brakes on the Casters with Brakes. 4.
3. Loosen and remove the Knob on each one of the M6 x 50 mm Button Head Screws. 4. Remove the two M6 x 50 mm Button Head Screws from the two holes located in the outer portion of the Support Pole. 5. Adjust the inner portion of the Support Pole to the desired height setting. 6. Insert two M6 x 50 mm Button Head Screws through the two holes located in the outer portion of the Support Pole. 7. Thread one Knob onto each one of the M6 x 50 mm Button Head Screws and hand tighten.
Warranty Information This product is backed by a five-year warranty. For further information on product warranty terms and conditions, please refer to www.startech.com/warranty. Limitation of Liability In no event shall the liability of StarTech.com Ltd. and StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
