Dual-Monitor Desk Mount - with Grommet/Desk-Clamp Mount *actual product may vary from photos User Manual SKU#: ARMBARDUOG For the latest information and specifications visit www.startech.
Compliance Statements Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.
Safety Statements Safety Measures • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines. Mesures de sécurité • L’installation et/ou le montage du produit doit être réalisé par un professionnel certifié et dans le respect des normes locales et du code de construction local.
Table of Contents Compliance Statements.........................................................................i Safety Statements...................................................................................ii Warning Statements...............................................................................iii Product Information...............................................................................1 Package Contents..............................................................................
Product Information Package Contents Column x 1 VESA Adapter x 2 CableManagement Clips (Column) x 2 End Caps x 2 CableManagement Clips (Monitor Arm) x 2 End-Cap Screws x2 Desk-Mount Clamp x 1 Hex Key x 1 Hex Key Screwdriver x 1 M4x14 mm Screws x 8 (narrow) M5x14 mm Screws x 8 (wide) Flat Washers x 8 GrommetMounting Adapter x1 GrommetMounting Plate x 1 Rubber Pads x 5 User Manual 1 Monitor Arms x 2 Instruction Manual x1
Product Dimensions Front View 1 1 2 3 4 1. Monitor Arms 2. Cable-Management Clips (Column) 3. Column 4. Desk-Mount Clamp Side View 1 1.
Top View 1 1 1. Cable-Management Clips (Monitor Arm) 368mm (14.
Grommet Mount 1 2 3 1. Mounting Cover 2. Grommet-Mounting Adapter 3. Grommet-Mounting Plate VESA Mount 1 1.
Technical Specifications Type of Measurement Measurement VESA mounting hole pattern 75x75 100x100 Weight capacity Up to 17.6 lb. (8 kg) per monitor mount kg Tilt +300 to -300 Screen size 330 to 686 mm (13 to 27 in.
Requirements • Two People for Installation • Mounting Surface • Desk-Mount Clamp (on Desk Edge) or Grommet Mount (in Desktop Grommet) • Two Monitors Note: Both Monitors must conform to the size, weight and VESA pattern requirements (see Technical Specifications).
Installation Attach the ARMBARDUOG to Your Mounting Surface There are two ways that you can attach the ARMBARDUOG to a mounting surface: a Desk-Mount Clamp or a Grommet Mount. The Desk-Mount Clamp ships preassembled. Use the Desk Clamp to Attach the ARMBARDUOG Warning! Ensure that the weight of the Monitors does not exceed the weight capacity of this product. If you exceed the weight capacity, you may experience personal injury or damage to your Monitors and ARMBARDUOG.
3. Screw the Column into the top of the Desk-Mount Clamp. (Figure 3) 4. Use the Hex Key Screwdriver to tighten the screws in the Desk-Mount Clamp. (Figure 4) Figure 3 Figure 4 Column Desk Clamp Hex Key Screwdriver 5. Seat the Mounting Cover so that it is flush with the top of the Desk-Mount Clamp.
6. Remove the backing from the five Rubber Pads and attach them underneath the top of the Desk-Mount Clamp, on the surface touching the table. (Figure 6) Figure 6 7. Turn the knob on the Desk-Mount Clamp counterclockwise until it reaches the thickness of the Desk. Note: The Desk-Mount Clamp can accommodate a Mounting Surface that is between 10 and 80 millimeters (0.4 and 3.1 inches) thick. 8. Slide the Desk-Mount Clamp over the edge of the Mounting Surface (Figure 7). 9.
Use the Grommet Mount to Attach the ARMBARDUOG Warning! Ensure that the weight of the Monitors does not exceed the weight capacity of this product. If you exceed the weight capacity, you may experience personal injury or damage to your Monitors and ARMBARDUOG. This product can support the following weight capacities: Up to 8 kg (17.6 lb.) per monitor mount, for a total of 16 kg (35.2 lb.). 1. Remove the Mounting Cover from the top of the Desk-Mount Clamp.
3. Affix the Rubber Pads to the bottom of the Grommet-Mounting Adapter. (Figure 10) Figure 10 GrommetMounting Adapter Rubber Pads 4. Slide the Mounting Cover over the Column and screw the Column into the top of the Grommet-Mounting Adapter. (Figure 11) Figure 11 Column Mounting Cover Grommet-Mounting Adapter 5. Use the hex side of the Hex Key Screwdriver to tighten the two Hex Screws in the Grommet-Mounting Adapter, and push down the Mounting Cover so that it sits flush with the Grommet-Mounting Adapter.
6. Thread the Grommet-Mounting Plate onto the Rod. 7. Place the assembled Column and Grommet-Mounting Adapter over the grommet hole in the Mounting Surface. On the underside of the Mounting Surface, insert the Rod up through the grommet hole and into the Column. Note: The Grommet-Mounting Adapter can accommodate a grommet hole that is between 10.5 and 50 millimeters (0.41 and 1.96 inches) in diameter.
3. Slide one of the Monitor Arms down the Column so that it sits against the Collar. 4. Slide a second Monitor Arm down the Column so that it sits against the first Monitor Arm. (Figure 15) Note: When you assemble the ARMBARDUOG for the first time, you need to use the Hex Key to tighten the Screws in each of the Monitor Arm joints.
Attach Monitors Warning! Attaching the Monitors is a two-person job. Do not attempt to complete this task by yourself. To accommodate different Monitor designs, the ARMBARDUOG comes with two sets of Screws that are different lengths and diameters. To select the appropriate Screws for the type of Monitors that you’re using, complete the following: • Determine whether the back of the Monitors are flush or inset. • Determine the depth of the mounting holes on the Monitors.
5. Complete steps 1 to 4 to add a VESA Adapter to a second monitor. 6. Slide one of the VESA Adapters with the Monitor attached over the end of one of the Monitor Arms attached to the Column. 7. Slide the second VESA Adapter and Monitor onto the other Monitor Arm. (Figure 18) 8. Place an End Cap over the end of each of the Monitor Arms attached to the Column.
9. Insert an End-Cap Screw through the hole in each of the End Caps and into the Monitor Arms, and tighten the End-Cap Screws in place.
Attach the Cable-Management Clips 1. Snap one of the Cable-Management Clips (Monitor Arm) over each of the two Monitor Arms. (Figure 21) Figure 21 Cable-Management Clip (Monitor Arm) Cable-Management Clip (Column) 2. Snap the two Cable-Management Clips (Column) over the Column. (Figure 22) Figure 22 Cable-Management Clips (Column) Column 3. Route the Monitor Cables through the Cable-Management Clips on the Monitor Arms and through the Cable-Management Clips on the Column.
Operation Adjust the Position of the Monitors You can configure the Monitors in many ways: (Figure 23 & 24): Figure 23 00 to 300 00 to 300 +300 to -300 +300 3600 3600 +300 -300 -300 Figure 24 +300 to to -300 -300 +300 +300 to -300 3600 +300 3600 -300 -300 User Manual +300 18
1. To position the Monitors: • To adjust the angle of the Monitor Arms, use the Hex Key to loosen the two Screws at each of the Monitor Arm joints. Position the Monitors as desired, and use the Hex Key to tighten the Screws and lock the Monitors into position. (Figure 25) Figure 25 Hex Key • To tilt the Monitors, use the Hex Key to loosen the Screw in the sides of the VESA Adapters. Position the Monitors as desired, and use the Hex Key to tighten the Screws and lock the Monitors into position.
• To raise or lower the Monitors minutely, use the Adjustment Screws located on the top of the VESA Adapters. (Figure 27) Figure 27 Adjustment Screw • To move the Monitors along the Monitor Arms, use a Phillips Head Screwdriver to loosen the Screw located on the underside of each of the VESA Adapters. Move the Monitors left or right on the Monitor Arms, and tighten each of the Screws when the Monitors are in the desired locations.
Warranty Information This product is backed by a three-year warranty. StarTech.com warrants its products against defects in materials and workmanship for the periods noted, following the initial date of purchase. During this period, the products may be returned for repair, or replacement with equivalent products at our discretion. The warranty covers parts and labor costs only. StarTech.com does not warrant its products from defects or damages arising from misuse, abuse, alteration, or normal wear and tear.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
