Triple-Monitor Stand ARMBARTRIO2 *actual product may vary from photos FR: Guide de l’utilisateur - fr.startech.com DE: Bedienungsanleitung - de.startech.com ES: Guía del usuario - es.startech.com NL: Gebruiksaanwijzing - nl.startech.com PT: Guia do usuário - pt.startech.com IT: Guida per l’uso - it.startech.com For the latest information, technical specifications, and support for this product, please visit www.StarTech.com/ARMBARTRIO2.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols PHILLIPS® is a registered trademark of Phillips Screw Company in the United States or other countries. This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.
Warning statements Mensagens de aviso Make sure that you assemble this product according to the instructions. Certifique-se de que monta este produto de acordo com as instruções. Read the entire manual and make sure that you understand the instructions before you start to assemble and use this product. Leia todo o manual e certifique-se de que entende as instruções antes de começar a montar e a utilizar este produto. Do not exceed the weight capacity of this product.
Table of Contents Warnings....................................................................................................................................................... i Product diagram.....................................................................................1 Product dimensions................................................................................1 Technical specifications.........................................................................2 Package contents..............
Product diagram VESA monitor mount VESA monitor mount VESA monitor mount Crossbar Right monitor arm Pole Left monitor arm Baseplate Product dimensions in.) m (55.6 1412 m in.) .4 m (52 1330 m in.) 35 mm (1.4 75 mm (2.9 in.) 463 mm (18.2 in.) 300 Instruction manual .5 in.) m (20 520 m 1 100 mm (3.9 in.) mm (11 .8 in .
Technical specifications Type of measurement Measurement 75x75 100x100 VESA LB kg 17.6 lb. (8 kg) per monitor RATED LOAD 3600 ROTATION -300 to +300 TILT Up to 686 mm (27 in.
Package contents 1 2 Crossbar VESA monitor mounts Qty: One Qty: Two 4 3 Left monitor arm Right monitor arm Qty: One Qty: One 5 Instruction manual 6 Arm caps Pole Qty: Two Qty: One 3
7 Baseplate End caps Qty: One Qty: Two 9 10 Cable-management clips Thumbscrews Qty: Four Qty: Two 12 11 Instruction manual 3 mm hex key 5 mm hex key Qty: One Qty: One 4
13 14 M4x14 mm screws M5x14 mm screws Qty: Twelve Qty: Twelve 15 16 Washers Instruction manual Qty: Twelve Qty: One Requirements • Three monitors that are compatible with one of the VESA mounting hole patterns that ARMBARTRIO2 supports • A Phillips type screwdriver Requirements are subject to change. For the latest requirements, please visit www.StarTech.com.ARMBARTRIO2.
Assembling the triple-monitor stand Assemble the base 1. Screw the pole into the baseplate. (figure 1) figure 1 Pole Baseplate 2. Use the 3 mm hex key to tighten the set screws to secure the pole to the baseplate.
Attach a monitor to the crossbar Warning! Make sure that the weight of the monitor that you attach to the crossbar does not exceed the weight capacity of this product. If you exceed the weight capacity, you might experience personal injury or damage to the product. This product can support up to 17. 6 lb. (8 kg) per monitor. 1. To accommodate different monitor designs, the ARMBARTRIO2 comes with two sets of screws that are different lengths and diameters.
Attach the VESA monitor mounts Warning! Make sure that the weight of the monitors that you are using does not exceed the weight capacity of this product. If you exceed the weight capacity, you might experience personal injury or damage to the product. This product can support up to 17.6 lb. (8 kg) per monitor. 1. Position one of the VESA monitor mounts over the mounting holes on the back of one of the monitors.
Attach the monitors to the monitor arms 1. Slide the left monitor arm through the VESA monitor mount attached to one of the monitors. 2. Slide the right monitor arm through the VESA monitor mount attached to the other monitor. (figure 5) figure 5 VESA monitor mount Right monitor arm VESA monitor mount Left monitor arm 3. Place an end cap on the end of each of the monitor arms. (figure 6) Note: Make sure that you line up the hole on the end cap with the corresponding hole on the end of the monitor arms.
4. Insert a thumbscrew through the hole in each of the end caps and into the monitor arms, and tighten the thumbscrews in place.
Attach the crossbar and monitor arms Warning! Attaching the crossbar and monitor arms is a two-person job. Do not attempt to complete this task by yourself. 1. Use the 3 mm hex key to loosen the screw in the collar on the pole. 2. Slide the collar to the height that you want the monitors to sit at, and use the 3 mm hex key to tighten the screw in the collar. (figure 8) figure 8 Pole Collar 3 mm hex key 3. Carefully slide the crossbar over the end of the pole so that it’s sitting against the collar.
4. Use the 5 mm hex key to tighten the four screws at the back of the crossbar. (figure 10) figure 10 5 mm hex key 5. Carefully place the left and right monitor arms over the projections on each end of the crossbar.
6. Place the arm caps into the two monitor arm joints. (figure 12) figure 12 Arm cap Arm joint Arm joint 7. If you’re assembling the ARMBARTRIO2 for the first time, you need to tighten the two screws in the monitor arm joints. Use the 5 mm hex key to tighten the screws.
Attach the cable-management clips 1. Snap the four cable-management clips over both of the monitor arms and the crossbar. (figure 14) figure 14 Cable-management clip 2. Route the monitor cables through the cable-management clips on the monitor arms and crossbar, down the pole, and through the cable-management clip on the pole.
Adjust the position of the monitors Tipping hazard warning Warning! The most stable configuration of the ARMBARTRIO2 is in the “flat” position with all three of the monitors positioned in a straight line. ARMBARTRIO2 can become unstable depending on how you position the monitors. If you adjust the position of the monitors, you should exercise caution and test the stability of the ARMBARTRIO2 before you use it in the adjusted configuration.
+300 to -300 +300 to -300 +300 -300 +300 -300 3600 3600 3600 1. To position the monitors in the way that works best for your setup, complete any of the following: • To adjust the angle of the left and right monitor arms, use the 5 mm hex key to loosen the two screws at each of the monitor arm joints. Position the monitors at the angle that you want them in, and use the 5 mm hex key to tighten the screws.
• To adjust the tilt angle of the left and right monitors, use the 5 mm hex key to loosen the screw in the sides of the VESA monitor mounts. Position the monitors at the angle that you want them in, and use the 5 mm hex key to tighten the screws. (figure 18) figure 18 Monitor arm 5 mm hex key • To raise or lower the left and right monitors minutely, use the adjustment screws located on the top of the VESA monitor mounts.
• To move the monitors along the monitor arms, use a Phillips screwdriver (not provided) to loosen the screw located on the underside of each of the VESA monitor mounts. Move the monitors left or right on the monitor arms, and tighten each of the screws when the monitors are in the locations that you want them in. (figure 20) Warning! Make sure that you loosen the screw on the underside of the VESA monitor mounts before you move them along the monitor arms.
Technical support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. For the latest drivers/software, please visit www.startech.com/downloads Warranty information This product is backed by a five-year warranty. StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.