Desk-Mount Dual Monitor Arm | Full Motion | Silver Actual product may vary from photos User Manual SKU#: ARMDUALPS For the latest information and specifications visit www.startech.
Compliance Statements Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.
Warning Statements • Make sure that you assemble this product according to the instructions. • Do not exceed the weight capacity of this product. Overloading this product might result in injury or property damage. This product can support the following weight: 44.09 lb. (20 kg). • This product is intended for indoor use only and should not be used outdoors. Varningsmeddelanden • Se till att du monterar produkten i enlighet med instruktionerna. • Överskrid inte produktens viktkapacitet.
Mensagens de aviso • Certifique-se de que monta este produto de acordo com as instruções. • Não exceda a capacidade de peso deste produto. Sobrecarregar este produto pode resultar em ferimentos ou danos de propriedade. Este produto pode suportar o seguinte peso: 20 kg. • Este produto destina-se apenas a uma utilização no interior e não deve ser utilizado no exterior. Advertencias de uso • Asegúrese de ensamblar este producto según las instrucciones.
Safety Statements Safety Measures • Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.
Table of Contents Compliance Statements.........................................................................1 Warning Statements...............................................................................2 Safety Statements...................................................................................4 Product Diagram.....................................................................................6 Product Dimensions.............................................................................
Product Diagram 1 2 3 6 4 5 1 Monitor Mount (x 2) 4 Support Pole 2 Swivel Arm (x 4) 5 C-Clamp 3 Monitor Shoulder 6 Cable-Management Clip To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Product Dimensions To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Product Dimension To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Product Information Specifications Type of measurement Measurement VESA mounting hole pattern 75x75 100x100 Tilt +900 to -150 Screen size Maximum 30 in. (762 mm) Rotate 3600 Swivel 3600 Weight/Load Capacity 44.09 lb. (20 kg) Lift 6.3 in. (160 mm) To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Package Contents Swivel Arms VESA Monitor Mounts Qty: Four Qty: Two Monitor Shoulder Support Pole w/ C-Clamp Qty: One Qty: One To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
M3 Hex Key EVA Cushion Qty: Two Qty: One Thumb Screws Qty: Eight To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Installation Using the Grommet Mount 1. Turn the Desk Mount over so that the Support Pole faces downwards. Use the M3 Hex Keys to remove the four Hex Screws that are holding the base of the Support Pole to the C-Clamp. Removing the Four Hex Screws 2. Use a Phillips Screwdriver (not included) to remove the Screw from the Plate on the C-Clamp. 3. Remove the Plate, Two Washers, and the Knob from the bottom of the C-Clamp.
Removing the Plate from the C-Clamp 4. Remove the backing from the EVA Cushion and attach it to the bottom of the Support Pole. Make sure that you line up the hole on the Support Pole with the corresponding hole on the EVA Cushion. 5. Position the Support Pole over the Grommet Hole. 6. Slide the Plate (removed in step 3) through the Threaded Rod on the Knob. 7. Place the Knob through the Grommet Hole in the desk or table and into the Support Pole. 8. Turn the Knob clockwise to tighten it.
Using the C-Clamp By default, the Desk Mount comes with the C-Clamp preassembled. If you assembled the Grommet mount and want to switch back to a C-Clamp. Skip to step 5 if you do not have to reassemble the C-Clamp. 1. Insert the Knob through the hole in the C-Clamp. Attaching the Knob to the C-Clamp 2. Place a Washer onto the Knob. 3. Place a Phillips Screw through a Round Washer, Plate, and into the Washer on the Knob.
Assembling the C-Clamp 4. Turn the Desk Mount over and use one of the M3 Hex Keys to insert four Hex Screws through the C-Clamp and into the base of the Mount. Attaching the Hex Screws to the C-Clamp 5. Remove the backing from the EVA Cushion. 6. Align the adhesive side of the EVA Cushion with the bottom of the Support Pole. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Installing the EVA Cushion 7. While applying pressure fix the EVA Cushion to the bottom of the Support Pole. 8. Using your hand, tighten the Knob until the C-Clamp is pressed tightly against the mounting surface. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Securing the C-Clamp to the Mounting Surface Note: You can adjust the size of the C-Clamp by removing the two screws holding the upper and lower portions of the clamp together and re-installing the screws into the lower two screw holes. Adjusting the C-Clamp To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Attaching the Monitor Mount Once the Desk Mount has been mounted to the mounting surface either by using the C-Clamp or Grommet. 1. Slide the Monitor Shoulder onto the Support Pole, so that it is resting on the Cable-Management Clip. Installing the Swivel Arm 2. Tighten the Mounting Shoulder using the Adjustment Screw located on the side of the Monitor Shoulder, using the M3 Hex Key. Be careful not to over-tighten the Monitor Shoulder.
Tightening the Monitor Shoulder 3. Align the Mounting Hole on Swivel Arm 1 with the Mounting Peg on the top of the Monitor Shoulder. 4. Slide the Mounting Hole on Swivel Arm 1 over the Mounting Peg until it clicks into place. Sliding the Swivel Arm into Place To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
5. Repeat steps 8 - 9 to install Swivel Arm 2. 6. Align the Mounting Hole on Swivel Arm 3 with the Mounting Peg on the top of Swivel Arm 1. 7. Slide the Mounting Hole on Swivel Arm 3 over the Mounting Peg until it clicks into place. Attaching the Swivel Arm 8. Repeat steps 11 - 12 to install Swivel Arm 4. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Attaching a Monitor Using the VESA Mount 1. Align the Mounting Holes (x 4) on the Monitor Mount with the mounting holes on the back of the Monitor. Note: When mounting the VESA mount the orientation of the Monitor is important. 2. Insert the Thumb Screws through the Monitor Mount and into the back of the Monitor. Mounting the Monitor Using the VESA Mount 3. Using your fingers, tighten the Thumb Screws. Warning! Do not over-tighten the Thumb Screws.
Attaching the Monitor Mount Notes: Attaching the Monitor Mount may require two people. The Monitor Mount supports up to a maximum of 44.09 lb. (20 kg). 1. While supporting the weight of the Monitor, carefully align the Mounting Hole on the Monitor Mount with the Mounting Peg on the top Swivel Arm. 2. Slide the Mounting Hole on the Monitor Mount over the Mounting Peg until it clicks into place. 3.
Removing the Monitor Mount 1. Slide the Thumb Clip towards the Monitor Mount, disengaging the locking mechanism. Sliding the Thumb Clip towards the Monitor Mount 2. While holding the Thumb Clip and the weight of the Monitor Mount, lift the Monitor Mount up, sliding the Mounting Peg out of the Mounting Hole. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Adjusting the Monitor Tilt • While supporting the weight of the Monitor, use the Hex Key (included) to loosen or tighten the Hex Screw on the side of the Monitor Mount, until the tension can hold the weight of the Monitor but it is still adjustable. Note: The screw cap located on the opposite side of the Hex Screw is not used for tilt adjustments. Routing the Cables The Desk Mount comes with a Cable-Management System that can be used to run the monitor cables down the mounting arms.
Warranty Information This product is backed by a ten-year warranty. For further information on product warranty terms and conditions, please refer to www.startech.com/warranty. Limitation of Liability In no event shall the liability of StarTech.com Ltd. and StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.