Vertical Dual Monitor Stand - Aluminum User Manual SKU#: ARMDUOVS For the latest information and specifications visit www.startech.
Compliance Statements Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.
Safety Statements • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines. • Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards. Mesures de Sécurité • L’installation et/ou le montage du produit doit être réalisé par un professionnel certifié et dans le respect des normes locales et du code de construction local.
Warning Statements • Make sure to assemble this product according to the instructions. Failure to do so might result in personal injury or property damage. • Make sure that the weight of the monitors doesn’t exceed the weight capacity of this product. If you exceed the weight capacity, you might experience personal injury or damage to the equipment. This product can support the following weight: 17.6 lb. (8 kg) per monitor mount. • Never operate this product if parts are missing or damaged.
Dichiarazioni di Avvertenza • Assemblare il prodotto rispettando le istruzioni. Il mancato rispetto delle istruzioni potrebbe causare danni a persone o proprietà. • Verificare che il peso del monitor non superi la capacità di supporto del prodotto. In caso di superamento della capacità di supporto potrebbero verificarsi danni a persone o apparecchiature. Il prodotto è in grado di supportare i seguenti pesi: 8 kg per monitor. • Non utilizzare il prodotto in presenza di parti mancanti o danneggiate.
注意 • 必ず取扱説明書に従って本製品の組み立てを行って下さい。取り扱いを誤 った場合に、傷害を負う恐れや物的損害が発生する恐れがあります。 • 取り付けるモニターの重量が、本製品で定められた最大積載重量を超えな いようにして下さい。最大積載重量をオーバーした場合、傷害を負う恐れや モニターや本製品に損害が発生する恐れがあります。本製品は、モニター1 台あたり10kgまで支持できます。 • 本製品で使用している部品の一部が紛失していたり損傷している状態で使 用するのは絶対に止めて下さい。 To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Table of Contents Compliance Statements.........................................................................i Safety Statements...................................................................................ii Warning Statements...............................................................................iii Product Information...............................................................................1 Package Contents..............................................................................
Product Information Package Contents VESA Mounts x 2 Lower Pole x 1 Upper Pole x 1 Base x 1 CableManagement Hooks x 2 CableManagement Hook Screws x 2 Washers x 8 M4 x 30 Screws x8 M5 x 14 Screws x8 Pole Connector x1 M4 x 14 Screws x8 M5 x 30 Screws x8 3 mm Hex Key x1 Spacers x 16 3 mm Hex Key with Screwdriver Tip x 1 4 mm Hex Key x1 User Manual x 1 To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Product Diagram VESA Mount HeightAdjustment Knob Collar Cable-Management Hook Cable-Management Clip Upper Pole Pole Connector VESA Mount HeightAdjustment Knob Cable-Management Hook Cable-Management Clip Collar Lower Pole Base To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Product Dimensions To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Technical Specifications Type of Measurement Measurement VESA Mounting Hole Pattern 75x75 100x100 Weight Capacity Up to 17.6 lb. (8 kg) Per Monitor kg Tilt +150 to -150 Maximum Screen Size 27” (686 mm) Rotate 3600 Swivel +150 to -150 To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Requirements For the latest requirements, please visit www.StarTech.com/ ARMDUOVS. • Two Monitors Note: Both Monitors must conform to the size, weight, and VESA pattern requirements (see Technical Specifications). • Phillips Head Screwdriver • (Optional) Two People for Installation To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Assembly Warning! Make sure that the weight of the Monitors does not exceed the weight capacity of this product. If you exceed the weight capacity, you might experience personal injury or damage to the product. Attach the Cable-Management Hooks 1. Place the two VESA Mounts upside down on your Desk. 2. Place the Cable-Management Hooks onto the corresponding circular indentations on the VESA Mounts. 3. Insert the Cable-Management Hook Screws through the Cable-Management Hooks and into the VESA Mounts.
4. Tighten the Cable-Management Hook Screws using a Phillips Head Screwdriver. Note: There is a slight indentation in the Cable-Management Hooks that allows you to fit a Phillips Head Screwdriver into the heads of the Cable-Management Hook Screws. Attach the Lower Column 1. Loosen the Hex Screws that are located on the Base using the 3 mm Hex Key. 2. Screw the Lower Pole onto the Base. Tighten the Hex Screws that are located on the Base using the 3 mm Hex Key. (Figure 2) Figure 2 3.
Attach the Lower VESA Mount 1. Loosen the Height-Adjustment Knob on one of the VESA Mounts. 2. Slide one VESA Mount over the Lower Pole. (Figure 3) Note: Do not tighten the Height-Adjustment Knob yet. Figure 3 Attach the Upper VESA Mount 1. Loosen the Hex Screws on the Pole Connector using the 3 mm Hex Key. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
2. Connect the Lower Pole to the Upper Pole using the Pole Connector: Screw the Pole Connector onto the Lower Pole. (Figure 4) Figure 4 3. Screw the Upper Pole into the Pole Connector. (Figure 5) 4. Tighten the Hex Screws on the Pole Connector using the 3 mm Hex Key. 5. Loosen the Height-Adjustment Knob on the second VESA Mount. 6. Slide the second VESA Mount over the Upper Pole. (Figure 6) Note: Do not tighten the Height-Adjustment Knob yet.
Figure 5 Figure 6 To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Attach the Monitors ARMDUOVS is designed to be used with Monitors that are the same size and weight. If you attach Monitors that are different sizes and weights to the ARMDUOVS, you do so at your own risk. To accommodate different Monitor designs, ARMDUOVS comes with four sets of Screws that are different lengths and diameters.
2. Place the two Monitors screen side down, on a flat, bare surface. Ensure that the Monitors are stacked, with the top of the lower Monitor touching the bottom of the upper Monitor. This will ensure a seamless fit. 3. Lift, tilt, and place the entire Monitor Mount Assembly over the two Monitors. 4. Adjust the two VESA Mounts, up or down the Upper or Lower Poles, so that the Mounting Holes on the VESA Mount align with the VESA Mounting Hole Pattern on the back of your Monitors. (Figure 8) Figure 8 5.
Figure 9 6. (Optional) If the VESA Mount does not sit flush with your Monitor, use the Spacers to close the gap between your Monitor and the VESA Mount. 7. Insert four of the appropriately sized Screws through the Washers, the VESA Mounts, and into each of the Monitors. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
8. Use a Phillips Screwdriver to tighten all of the Screws. Warning! Do not over-tighten the Screws. If you encounter resistance while you’re tightening the Screws, stop tightening. Failure to do so could result in damage to the Monitors. 9. Tighten the Height-Adjustment Knob on each of the VESA Mounts. (Figure 10) Note: The Height-Adjustment Knob has a ratchet feature. Freely rotate the Height-Adjustment Knob by pulling it away from the VESA Mount and rotating it to the desired position. Figure 10 10.
Cable Management 1. Connect the Power and Video Cables to each Monitor. 2. Route the Power and Video Cables through the CableManagement Hooks. 3. Route the Power and Video Cables through the CableManagement Clips. (Figure 11) Figure 11 Monitor Placement Warning! Lifting the Monitor Mount Assembly is a twoperson job. Do not attempt to complete this task by yourself. Tipping hazard! ARMDUOVS is free-standing and when you attach Monitors to it, you increase the tipping hazard.
1. With Two People: Lift the Monitor Mount Assembly into an upright position. 2. Position the Monitor Mount Assembly on the desired location of your Desk. 3. Connect the Video Cables from each Monitor into your Computer, Laptop, or Docking Station. 4. Connect the Power Cables from each Monitor to an AC Electrical Outlet. Operation Adjust the Monitor Height Warning! Adjusting the Monitor height is a two-person job. Do not attempt to complete this task by yourself. 1.
6. Person two: Tighten the Height-Adjustment Knob on each of the VESA Mounts. Adjust the Swivel ARMDUOVS comes ready for swivel adjustments. Your Monitors can easily be adjusted by swivelling the Monitors from side to side. To increase or reduce the tension for the swivel adjustment, follow these steps: 1. Remove the Cap located on the VESA Mount to reveal the 4 mm Hex Screw. The Cap is located above the CableManagement Hook. (Figure 12) Figure 12 2. Loosen the 4 mm Hex Screw. 3.
5. Return the Cap to its original position. Adjust the Tilt and Rotation ARMDUOVS comes ready for tilt and rotation adjustments. Your Monitors can easily be adjusted by tilting the Monitors forwards or backwards, or side to side. You can also rotate your Monitors from portrait to landscape view. To increase or reduce the tension for the tilt and rotation adjustments, follow these steps: 1. Loosen the three Hex Screws on the rear of the VESA Mounts using the 3 mm Hex Key.
2. Tilt your Monitors to the desired viewing angle. Or Rotate your Monitors to portrait or landscape view. Note: Ensure that there is ample clearance to fit both Monitors. Some adjustments to the height of the VESA Mount will be necessary in order to tilt or rotate your Monitors. 3. Tighten the three Hex Screws on the rear of the VESA Mounts using the 3 mm Hex Key. Note: Do not over-tighten the Hex Screws. Quickly Removing a VESA Mount 1.
2. Slide the VESA Mount up to remove it from the VESA Mount Holder. (Figure 15) Figure 15 Quickly Attaching a VESA Mount 1. Align the VESA Mount with the VESA Mount Holder and slide the VESA Mount down aligning the Hex Screw Hole on the VESA Mount with the Hex Screw Hole on the VESA Mount Holder. 2. Insert the two Hex Screws through the Hex Screw Holes on the VESA Mount Holder and into the Hex Screw Holes on the VESA Mount. 3. Using the 3 mm Hex Key, tighten the Hex Screw.
Warranty Information This product is backed by a two-year warranty. For further information on product warranty terms and conditions, please refer to www.startech.com/warranty. Limitation of Liability In no event shall it be the liability of StarTech.com Ltd. and StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.