Quad-Monitor Arm ARMQUAD *actual product may vary from photos FR: Guide de l’utilisateur - fr.startech.com DE: Bedienungsanleitung - de.startech.com ES: Guía del usuario - es.startech.com NL: Gebruiksaanwijzing - nl.startech.com PT: Guia do usuário - pt.startech.com IT: Guida per l’uso - it.startech.com For the latest information, technical specifications, and support for this product, please visit www.StarTech.com/ARMQUAD.
Warning statements Waarschuwingen Make sure to assemble this product according to the instructions. Failure to do so might result in personal injury or property damage. Zorg dat dit product volgens de instructies in elkaar wordt gezet. Indien dit niet goed gebeurt kan lichamelijk letsel of materiële schade ontstaan. Make sure that the weight of the monitor doesn’t exceed the weight capacity of this product.
Table of Contents Warnings....................................................................................................................................................... i Introduction.............................................................................................1 Product diagram......................................................................................................................................... 1 Product dimensions...................................................
Introduction Use the ARMQUAD to mount four monitors, and use the cable-management clips to keep your cables organized. Adjust the position of the monitors to set up your work station in the way that works best for you.
Product dimensions Instruction manual 2
Technical specifications Type of measurement Measurement VESA mounting hole pattern 75x75 100x100 Weight capacity Up to 17.6 lb. (8 kg) per monitor mount kg Tilt +300 to -300 Screen size 330 to 686 mm (13 to 27 in.
Package contents 1 2 Monitor arms VESA monitor mounts Qty: Four Qty: Four 4 3 Lower pole Upper pole Qty: One Qty: One 5 6 Pole connector Cable-management clips Qty: One Qty: Four 8 7 Instruction manual End caps Thumbscrews Qty: Four Qty: Four 4
9 10 Desk clamp 3 mm hex key Qty: One Qty: One 12 11 5 mm hex key M4x14 mm screws Qty: One Qty: Sixteen 13 14 M5x14 mm screws Washers Qty: Sixteen Qty: Sixteen 16 15 Grommet collar Grommet plate Qty: One Qty: One Instruction manual 5
17 18 Rubber pads Instruction manual Qty: Five Qty: One Requirements • Four monitors or displays that are compatible with a VESA mount • A Phillips screwdriver Requirements are subject to change. For the latest requirements, please visit www.StarTech.com/ARMQUAD.
Assembly Attach the ARMQUAD to your mounting surface There are two ways that you can attach the ARMQUAD to your mounting surface: a desk clamp or a grommet mount. The desk clamp ships preassembled. Use the desk clamp to attach the ARMQUAD Warning! Make sure that the weight of the monitors doesn’t exceed the weight capacity of this product. If you exceed the weight capacity, you might experience personal injury or damage to the product. This product can support the following weight: Up to 8 kg (17.6 lb.
3. Screw the lower pole and cap into the top of the desk clamp. (figure 3) 4. Use the 3 mm hex key (10) to tighten the screws in the desk clamp. (figure 4) figure 3 figure 4 Lower pole Desk clamp 3 mm hex key 5. Push down the cap so that it sits flush against the top of the desk clamp.
6. Remove the backing from the five rubber pads (17) and attach them underneath the top of the desk clamp. 7. Turn the knob on the desk clamp counterclockwise until you reach the thickness of the desk or table that you’re attaching the ARMQUAD to. Note: The desk mount can accommodate a desk or table that’s between 10 and 80 mm (0.4 and 3.1 in.) thick. 8. Slide the desk clamp over the edge of the desk or table (figure 6). 9. Turn the knob clockwise to tighten the desk clamp.
2. Thread a Phillips screwdriver through the top of the desk clamp and unscrew the screw and remove the washer and plate. (figure 8) Tip! Keep the screw, washer, and plate in a safe place so that you can use them again if you want to switch back to the desk clamp. 3. Remove the rod from the bottom of the desk clamp. (figure 8) figure 8 Screwdriver Desk clamp Screw Plate Rod 4. Thread the lower pole (3) through the cap that you removed from the desk clamp.
5. Remove the backing from the five rubber pads (17) and affix them to the bottom of the grommet collar (15). (figure 10) figure 10 Grommet collar Rubber pads 6. Screw the lower pole and cap into the top of the grommet collar. (figure 11) figure 11 Pole Cap Grommet collar 7. Use the 3 mm hex key (10) to tighten the screw in the grommet collar, and push down the cap so that it sits flush again the grommet collar.
8. Thread the grommet plate (16) onto the rod. 9. Place the assembled lower pole and grommet collar over the grommet hole in your mounting surface. On the underside of the mounting surface, thread the rod up through the grommet hole and into the lower pole. 10. Turn the knob clockwise to tighten the grommet mount. (figure 13) figure 13 Lower pole Grommet plate Rod Attach monitor arms to the lower pole 1. Use the 3 mm hex key (10) to loosen the screw in the collar on the lower pole (3). 2.
3. Slide one of the monitor arms (1) down the lower pole so that it sits against the collar. 4. Slide a second monitor arm down the lower pole so that it sits against the first monitor arm and extends in the opposite direction of the first monitor arm. (figure 15) figure 15 Monitor arm Monitor arm Collar Lower pole Note: When you assemble the ARMQUAD for the first time, you need to use the 5 mm hex key (11) to tighten the screws in each of the monitor arm joints.
Attach monitors to the monitor arms on the lower pole Warning! Attaching the monitors is a two-person job. Do not attempt to complete this task by yourself. To accommodate different monitor designs, the ARMQUAD comes with two sets of screws that are different lengths and diameters. To select the appropriate screws for the type of monitors that you’re using, complete the following: • Determine whether the back of the monitors are flush or inset. • Determine the depth of the mounting holes on the monitors.
5. Complete steps 1 to 4 to add a VESA monitor mount to a second monitor. 6. Slide one of the VESA monitor mounts with the monitor attached over the end of one of the monitor arms (1) attached to the lower pole (3). 7. Slide the second VESA monitor mount and monitor over the end of the other monitor arm attached to the lower pole. (figure 18) figure 18 Top of monitor Top of monitor Monitor arm Monitor arm VESA monitor mount Lower pole VESA monitor mount 8.
figure 20 End cap Thumbscrew Attach monitor arms to the upper pole 1. Screw the pole connector (5) onto the end of the lower pole (3).
2. Screw the upper pole (4) into the pole connector. (figure 22) figure 22 Upper pole Pole connector Lower pole 3. Use the 3 mm hex key (10) to tighten the two screws in the side of the pole connector.
4. Use the 3 mm hex key to loosen the screw in the collar on the upper pole. 5. Slide the collar to the height that you want the two monitors to sit at, and use the 3 mm hex key to tighten the screw in the collar. (figure 24) figure 24 Upper pole Collar 3 mm hex key 6. Slide one of the monitor arms (1) down the upper pole so that it sits against the collar. 7. Slide the fourth monitor arm down the upper pole so that it sits against the other monitor arm and extends in the opposite direction.
Attach monitors to the monitor arms on the upper pole Warning! Attaching the monitors is a two-person job. Do not attempt to complete this task by yourself. To accommodate different monitor designs, the ARMQUAD comes with two sets of screws that are different lengths and diameters. To select the appropriate screws for the type of monitors that you’re using, complete the following: • Determine whether the back of the monitors are flush or inset. • Determine the depth of the mounting holes on the monitors.
5. Complete steps 1 to 4 to add a VESA monitor mount to a second monitor. 6. Slide one of the VESA monitor mounts with the monitor attached over the end of one of the monitor arms (1) attached to the upper pole (4). 7. Slide the second VESA monitor mount and monitor over the end of the other monitor arm attached to the upper pole. (figure 27) figure 27 Top of monitor Top of monitor Monitor arm Monitor arm VESA monitor mount Upper pole VESA monitor mount 8.
9. Insert a thumbscrew (8) through the hole in each of the end caps and into the monitor arms, and tighten the thumbscrews in place.
Adjust the position of the monitors You can adjust the position and angle of your monitors in the following ways: 00 to 300 00 to 300 +300 to -300 +300 to -300 +300 3600 3600 +300 -300 -300 +300 to -300 +300 to -300 3600 +300 3600 -300 -300 Instruction manual +300 22
1. To position the monitors in the way that works best for your setup, do any of the following: • To adjust the angle of the monitor arms (1), use the 5 mm hex key (11) to loosen the two screws at each of the monitor arm joints. Position the monitors at the angles that you want them in, and use the 5 mm hex key to tighten the screws and lock the monitors into position.
• To raise or lower the monitors minutely, use the adjustment screws located on the top of the VESA monitor mounts (2). (figure 32) figure 32 Adjustment screw • To move the monitors along the monitor arms (1), use a Phillips screwdriver to loosen the screw located on the underside of each of the VESA monitor mounts (2). Move the monitors left or right on the monitor arms, and tighten each of the screws when the monitors are in the locations that you want them in.
Attach the cable-management clips 1. Snap one of the cable-management clips (6) over each of the four monitor arms (1). (figure 34) figure 34 Cable-management Monitor arm clip 2. Route the monitor cables through the cable-management clips on the monitor arms and through the cable-management clips on the poles.
Technical support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. For the latest drivers/software, please visit www.startech.com/downloads Warranty information This product is backed by a two-year warranty. StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
