Quad Monitor Stand - Silver *actual product may vary from photos User Manual SKU#: ARMQUADSS For the latest information and specifications visit www.startech.
Compliance Statements Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.
Safety Statements • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines. • Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards. Mesures de Sécurité • L’installation et/ou le montage du produit doit être réalisé par un professionnel certifié et dans le respect des normes locales et du code de construction local.
Warning Statements • Make sure to assemble this product according to the instructions. Failure to do so might result in personal injury or property damage. • Make sure that the weight of the monitors doesn’t exceed the weight capacity of this product. If you exceed the weight capacity, you might experience personal injury or damage to the equipment. This product can support the following weight: 17.6 lb. (8 kg) per monitor mount. • Never operate this product if parts are missing or damaged.
Dichiarazioni di Avvertenza • Assemblare il prodotto rispettando le istruzioni. Il mancato rispetto delle istruzioni potrebbe causare danni a persone o proprietà. • Verificare che il peso del monitor non superi la capacità di supporto del prodotto. In caso di superamento della capacità di supporto potrebbero verificarsi danni a persone o apparecchiature. Il prodotto è in grado di supportare i seguenti pesi: 8 kg per monitor. • Non utilizzare il prodotto in presenza di parti mancanti o danneggiate.
注意 • 必ず取扱説明書に従って本製品の組み立てを行って下さい。取り扱いを誤 った場合に、傷害を負う恐れや物的損害が発生する恐れがあります。 • 取り付けるモニターの重量が、本製品で定められた最大積載重量を超えな いようにして下さい。最大積載重量をオーバーした場合、傷害を負う恐れや モニターや本製品に損害が発生する恐れがあります。本製品は、モニター1 台あたり8 kgまで支持できます。 • 本製品で使用している部品の一部が紛失していたり損傷している状態で使 用するのは絶対に止めて下さい。 To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Table of Contents Compliance Statements.................................................................................... i Safety Statements............................................................................................... ii Warning Statements........................................................................................... iii Product Information........................................................................................... 1 Package Contents...........................
Adjusting the Monitors..................................................................................... 22 Tilt Adjustment........................................................................................................................................... 22 Swivel Adjustment..................................................................................................................................... 23 Rotation Adjustment......................................................................
Product Information Package Contents Swivel Arms VESA Mounts Shoulders Upper Pole Qty: 4 Qty: 4 Qty: 2 Qty: 1 Lower Pole Pole Connector Base Qty: 1 Qty: 1 Qty: 1 CableManagement Clips Qty: 2 Screws: Screws: M4x12 mm M5x12 mm M4x16 mm M5x16 mm Spacers Washers M4x20 mm M5x20 mm Qty: 32 Qty: 16 Qty: 16 (of each) Qty: 16 (of each) 1
3 mm Hex Key with Screwdriver Tip Qty: 1 6 mm Hex Key User Manual Qty: 1 Qty: 1 To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Product Diagram Dimensions To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Front View 1 2 3 4 1 VESA Mounts 2 Swivel Arms 3 Pole Connector 4 Base To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Rear View 5 6 5 Shoulder 6 Cable-Management Clip To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Side View 7 8 7 Upper Pole 8 Lower Pole To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Technical Specifications Type of Measurement Measurement VESA Mounting Hole Pattern 75x75 100x100 Weight Capacity Up to 17.6 lb. (8 kg) Per Monitor kg Tilt +900 to -400 Maximum Screen Size 32” (813 mm) Rotate 3600 Swivel 3600 To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Requirements For the latest requirements, please visit www.startech.com/ARMQUADSS. • Four Monitors Note: All four Monitors must conform to the size, weight, and VESA pattern requirements (see Technical Specifications). • Phillips Head Screwdriver • Two People for Installation • (Optional) Two People for Adjustments To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Assembly Warning! Make sure that all of the hardware is assembled properly and checked for stability before you load the Monitors. Warning! Make sure that the weight of the Monitors does not exceed the weight capacity of this product. If you exceed the weight capacity, you might experience personal injury or damage to the product. Assemble the Base 1. Loosen the Hex Screws that are located on the Base using the 3 mm Hex Key with Screwdriver Tip. 2. Slide the Cable-Management Clip onto the Lower Pole.
Figure 1 Collar 3 mm Hex Key with Screwdriver Tip Lower Pole Cable-Management Clip Base Adjust the Collar on the Lower Pole 1. Loosen the Flat-Head Screws on the Collar, using the 3 mm Hex Key with Screwdriver Tip. 2. Slide the Collar up or down the Lower Pole so that it sits at the desired height for your Monitors. 3. Tighten the two Flat-Head Screws that are located on the Collar, using the 3 mm Hex Key with Screwdriver Tip.
Figure 2 Collar 3 mm Hex Key with Screwdriver Tip Attach the Shoulder to the Lower Pole 1. 2. 3. Rotate the Lever on the Shoulder down/counterclockwise to loosen the Shoulder. Freely rotate the Lever by pulling it away from the Shoulder and rotating it to the top position, then rotate the Lever down/counterclockwise to loosen the Shoulder. Note: The Lever has a ratchet feature.
Figure 3 Shoulder Shoulder Lever Attach the Swivel Arms to the Lower Pole 1. Insert the Swivel Arms into the Sockets of the Shoulder until each Swivel Arm clicks into place. (Figure 4) To remove the Swivel Arms: Locate the Clip on the bottom of the Swivel Arms. Toggle this Clip sideways and pull upwards. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Figure 4 Swivel Arms Swivel Arm Clip To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Attach the Upper Pole 1. Loosen the Hex Screws that are located on the Pole Connector using the 3 mm Hex Key with Screwdriver Tip. 2. Screw the Pole Connector onto the Lower Pole. 3. Slide the Cable-Management Clip onto the Upper Pole. 4. Screw the Upper Pole into the Pole Connector. 5. Tighten the Hex Screws that are located on the Pole Connector using the 3 mm Hex Key with Screwdriver Tip.
Adjust the Collar on the Upper Pole 1. Loosen the Flat-Head Screws on the Collar located on the Upper Pole, using the 3 mm Hex Key with Screwdriver Tip. 2. Slide the Collar up or down the Upper Pole so that it sits at the desired height for the two upper Monitors. 3. Tighten the two Flat-Head Screws that are located on the Collar, using the 3 mm Hex Key with Screwdriver Tip.
Attach the Shoulder to the Upper Pole 1. 2. 3. Rotate the Lever on the Shoulder down/counterclockwise to loosen the Shoulder. Freely rotate the Lever by pulling it away from the Shoulder and rotating it to the top position, then rotate the Lever down/counterclockwise to loosen the Shoulder. Note: The Lever has a ratchet feature. Freely rotate the Lever, without engaging the tightening mechanism, by pulling it away from the Shoulder and rotating it to the desired position.
Attach the Swivel Arms to the Upper Pole 1. Insert the Swivel Arms into the Sockets of the Shoulder, located on the Upper Pole, until each Swivel Arm clicks into place. (Figure 8) To remove the Swivel Arms: Release the Clip that is located on the bottom of the Swivel Arms, where the Swivel Arms connect to the Shoulder, and pull upwards. Figure 8 Swivel Arms Upper Pole Clip Lower Pole To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Attach the VESA Mounts to the Monitors ARMQUADSS is designed to be used with Monitors that are the same size and weight. If you attach Monitors that are different sizes and weights to ARMQUADSS, you do so at your own risk. To accommodate different Monitor designs, ARMQUADSS comes with six sets of Screws that are different lengths and diameters.
Figure 9 Screw Washer VESA Mount 5. Use a Phillips Head Screwdriver to tighten the Screws. Warning! Do not over-tighten the Screws. If you encounter resistance while you’re tightening the Screws, stop tightening. Failure to do so could result in damage to the Monitor. Figure 10 Screw Washer Spacers To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
6. Complete steps 1 to 4 to add a VESA Mount to the three remaining Monitors. Attach the VESA Mounts to the Swivel Arms Warning! Attaching the Monitors is a two-person job. Do not attempt to complete this task by yourself. Tipping hazard! ARMQUADSS is free-standing and when you attach Monitors to it, you increase the tipping hazard. A second person is required to keep ARMQUADSS upright as you attach the Monitors. 1.
Figure 11 VESA Mount To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Adjusting the Monitors Warning! The most stable configuration of ARMQUADSS is the “flat” position, with all four of the Swivel Arms positioned in a straight line. ARMQUADSS can become unstable depending on how you position the Monitors. If you adjust the position of the Monitors, you should exercise caution and test the stability of ARMQUADSS before you use it in the adjusted configuration.
Figure 12 Hex Screw 6 mm Hex Key Swivel Adjustment The Monitors can be adjusted on a 360-degree swivel. • Place one hand on the left side of the Monitor and the other hand on the right side of the Monitor. Apply light pressure to swivel the Monitors either left or right. Rotation Adjustment The Monitors can be adjusted to be configured in a portrait or landscape view. Note: Ensure that there is ample clearance to fit all four Monitors.
• Place one hand on the left side of the Monitor and the other hand on the right side of the Monitor. Apply light pressure to rotate the Monitors into a portrait or landscape view. Micro Height Adjustment 1. Insert the 6 mm Hex Key into the Height-Adjustment Knob that is located on the top of the VESA Mounts. 2. Turn the 6 mm Hex Key, or the Height-Adjustment Knob, clockwise to lower the Monitors or counterclockwise to raise the Monitors. (Figure 13) 3.
Cable Management The Power and Video Cables from your Monitors can be organized and contained within the Swivel Arms and alongside the Upper and Lower Poles. To manage the Cables running to your Monitors, complete the following steps: 1. Connect the Power and Video Cables to each Monitor. 2. Route the Cables for the Monitors along the bottom of the Swivel Arms. 3. Locate the integrated Cable-Management Channels within the Swivel Arms and gently press the Cables into the Channels.
Figure 14 Cable-Management Channel To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Warranty Information This product is backed by a five-year warranty. For further information on product warranty terms and conditions, please refer to www.startech.com/warranty. Limitation of Liability In no event shall the liability of StarTech.com Ltd. and StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
