Dual Monitor Mount with Built-In 2-Port USB Pass-Through ARMSLIMDUO *actual product may vary from photos FR: Guide de l’utilisateur - fr.startech.com DE: Bedienungsanleitung - de.startech.com ES: Guía del usuario - es.startech.com NL: Gebruiksaanwijzing - nl.startech.com PT: Guia do usuário - pt.startech.com IT: Guida per l’uso - it.startech.com For the latest information, technical specifications, and support for this product, please visit www.startech.com/ARMSLIMDUO.
Table of Contents Introduction.............................................................................................1 Packaging contents................................................................................................................................... 1 Product diagram.....................................................................................2 Product dimensions..................................................................................................................
Introduction You can use the ARMSLIMDUO to mount two displays on your desk and take advantage of the full-motion articulation and the cable-management system that comes with the ARMSLIMDUO. The ARMSLIMDUO features two 3.5 mm audio ports and two USB pass-through ports, and comes with a desk-clamp mount.
Product diagram VESA monitor mounts Cable cover Cable cover Mounting arms Cable cover Cable cover Close-up view of the base Audio port Microphone port USB A pass-through ports Instruction manual 2
Product dimensions Instruction manual 3
Technical specifications The ARMSLIMDUO can support up to 8.0 kg (17.6 lb) of weight per mounting arm. The desk clamp can support a maximum thickness of 90 mm (3.54 in.). Assemble the ARMSLIMDUO Warning! Make sure that all of the hardware is assembled securely and checked for stability before you load the monitors. Note: You will need a Phillips screwdriver to assemble the ARMSLIMDUO. Attach the desk clamps to the mounting arms 1.
8. Repeat steps 5 to 7 for the second desk clamp (lower bracket). figure 2 11 2 9 3 Attach the mounting arm to a desk or table 1. Turn the hand screws on the desk clamps (lower bracket) (3) counterclockwise until you reach the thickness of the desk or table (figure 3). 2. Slide the desk clamp over the edge of the desk or table and turn the hand screws on the desk clamps clockwise until the mounting arm is securely fastened to the desk or table.
Attach the monitors to the VESA monitor mounts Warning! To prevent scratching during the installation process, you should handle the surface of the monitors with care. Do one of the following: • To install monitors that have a flush installation surface, insert four of the M4x12 mm screws (5) through one of the VESA monitor mounts (4) and into the mounting holes on the back of the monitor. Use a Phillips screwdriver to tighten the screws.
Attach the VESA monitor mounts to the mounting arm 1. Slide one of the VESA monitor mounts (4) with the monitor attached into the slot on one of the mounting arms (1) (figure 6). 2. Repeat step 1 for the second monitor that you’re attaching. figure 6 4 1 3. If the monitor doesn’t stay in place or the movement is stiff, do one of the following: • To increase the tension, use the M5 Allen key (9) to turn the screws in the monitor arms clockwise (figure 7).
4. To change the tilt tension, use the M5 Allen key to turn the screws closest to the VESA monitor mounts clockwise or counterclockwise (figure 8). figure 8 4 9 5. To change the swivel tension, use the M5 Allen key to turn the second screws from the VESA monitor mounts clockwise (figure 9). figure 9 9 4 To remove a VESA monitor mount from the mounting arm, press the metallic tab on the back of the monitor mount and pull it up off of the mounting arm.
Route the cables Make sure that the cables that you’re routing are unplugged before you complete the following steps. 1. Remove the cable covers from the spring mounting arms. 2. Run the cables along one of the spring mounting arms and hold the cables in place while you snap the cable covers back onto the spring mounting arm (figure 10). 3. Repeat step 2 for the second set of cables. figure 10 Spring mounting arm Cable cover 4.
Manage your cables You can use the integrated pass-through ports on the ARMSLIMDUO to conveniently extend your computer connections to the base of the monitor mount and keep your cables organized. To avoid cluttering your desk with cables, you can plug your devices into the monitor mount instead of directly into your computer system. • Do any of the following: • Plug the green audio cable jack located at the back of the monitor mount into the appropriate audio port on your computer.
Technical support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. For the latest drivers/software, please visit www.startech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.