Monitor Wall Mount - Aluminum ARMWALL *actual product may vary from photos FR: Guide de l’utilisateur - fr.startech.com DE: Bedienungsanleitung - de.startech.com ES: Guía del usuario - es.startech.com NL: Gebruiksaanwijzing - nl.startech.com PT: Guia do usuário - pt.startech.com IT: Guida per l’uso - it.startech.com For the latest information, technical specifications, and support for this product, please visit www.StarTech.com/ARMWALL.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols PHILLIPS® is a registered trademark of Phillips Screw Company in the United States or other countries. This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.
Warning statements Mensagens de aviso Make sure to assemble this product according to the instructions. Failure to do so might result in personal injury or property damage. Certifique-se de que monta este produto de acordo com as instruções. O incumprimento pode resultar em ferimentos pessoais ou danos de propriedade. Make sure that the weight of the TV doesn’t exceed the weight capacity of this product. If you exceed the weight capacity, you might experience personal injury or damage to the equipment.
Table of Contents Warnings....................................................................................................................................................... i Introduction.............................................................................................1 Product diagram......................................................................................................................................... 1 Technical specifications.............................................
Introduction Product diagram Display mount Mounting plate 90° +45° -45° Instruction manual 1
Technical specifications Type of measurement Measurement VESA mounting hole pattern 50x50 75x75 100x100 Rated load Up to 15 kg (33 lb.) kg Tilt +450 to -450 Screen size Between 330 mm and 686 mm (13 in. and 27 in.
Package contents 1 2 Display mount Hex key Qty: One Qty: One 4 3 Wrench M4x14 mm screws Qty: One Qty: Four 5 6 M5x14 mm screws Washers Qty: Four Qty: Four Instruction manual 3
7 Mounting screws Screw anchors Qty: Two Qty: Two 9 Instuction manual Qty: One Requirements • A monitor or display that is compatible with one of the VESA mounting hole patterns that ARMWALL supports • A Phillips screwdriver Requirements are subject to change. For the latest requirements, please visit www.StarTech.com/ARMWALL.
Installation Attach the display mount to a wall Warning! Wall structures vary, and it is important that you make sure that the type of structure and mounting hardware that you are using will properly support the mounted equipment. Failure to do so may result in personal injury and/or equipment damage. The wall structure should be capable of supporting at least four times the weight of the mounted equipment.
3. Use the holes in the mounting plate as a template and use a pencil to mark the location on the wall where you want to attach the display mount. (figure 2) 4. Follow the appropriate steps for the type of wall that you’re using and attach the mounting plate to the wall. figure 2 Mounting plate Attach a monitor to the display mount To accommodate different monitor sizes, the ARMWALL comes with two sets of screws that are different lengths and diameters.
4. Use a Phillips screwdriver to tighten the screws.(figure 3) Warning! Do not over-tighten the screws. If you encounter resistance while you’re tightening the screws, stop tightening. Failure to do so could result in damage to the monitor.
Adjust the tilt tension 1. Use the hex key to prevent the screw on the display mount from moving as you tighten the nut. 2. Use the wrench to tighten the nut on the side of the display mount.
Attach the display mount to the mounting plate Warning! Attaching the monitor is a two-person job. Do not attempt to complete this task by yourself. 1. Carefully pick up the display mount with the monitor attached and slide it onto the mounting plate. 2. Insert the screw into the display mount and mounting plate. 3. Use a Phillips screwdriver to tighten the screw.
Technical support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. For the latest drivers/software, please visit www.startech.com/downloads Warranty information This product is backed by a two-year warranty. StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
