Single-Module Conference Table Box Actual product may vary from photos User Manual SKU#: BEZ4MOD For the latest information and specifications visit www.startech.
Compliance Statements Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.
Mesures de sécurité • Les terminaisons de câblâge ne doivent pas être effectuées lorsque le produit et/ou les câbles électriques sont sous tension. • L’installation et/ou le montage du produit doit être réalisé par un professionnel certifié et dans le respect des normes locales et du code de construction local.
Table of Contents Compliance Statements.........................................................................1 Safety Statements...................................................................................1 Warning Statements...............................................................................2 Product Diagram.....................................................................................4 Product Information............................................................................
Product Diagram Installation Holes Mounting Slot Lacing Bar Mounting Holes (2) To view manuals, videos, drivers, downloads, and more visit www.startech.
Product Information Package Contents BOX4MODULE • Modular Table Box x 1 • Installation Kit • Wing Fastener x 2 • Die Cut Outline x 1 • Lacing Bar x 1 • Lacing Bar Screws (M4 x 4 mm) x 4 • Cable Management Module • Cable Management Bracket x 1 • Cable Management Top Plates x 2 • Cable Management Plate Screws (#6-32 x 3/8”) x 4 • Cable Management Bracket Mounting Screws (#6-32 x 3/8”) x 4 • Small Cable Bushing x 1 • Large Cable Bushing x 1 • User Manual x 1 To view manuals, videos, drivers, downloads, and mo
Requirements Installation: Installation requirements are sold separately. • Surface for Installation • Cable Ties • Tools • 3/8 Wood Drill Bit x 1 • Phillips Head Screwdriver x 1 • Jigsaw x 1 • Drill x 1 • Writing Utensil x 1 • Painter’s Tape x 1 Module: Module requirements are optional and will depend on the configuration needed for the Conference Table setup.
Installation For additional information on installing the Modular Table Box, please visit www.startech.com/BEZ4MOD to watch the installation video. Notes: StarTech.com is not responsible for any damages related to the installation of this product. Prior to installation, please test the product’s port compatibility with all devices and displays intended for use with this product. The thickness of the table surfaced used for installation should not exceed 2.25 inches.
3. Using a Writing Utensil, trace around the Surface Cut-Out Area to create a guide on the table’s surface. Surface Cut-Out Area 4. Carefully remove the Surface Cut-Out Area from the table’s surface. To view manuals, videos, drivers, downloads, and more visit www.startech.
5. Using a Drill with a 3/8” Wood Drill Bit, carefully drill pilot holes in each of the four corners of the guide. Drill Pilot Holes To view manuals, videos, drivers, downloads, and more visit www.startech.
6. Insert the Jigsaw Blade into one of the pilot holes and carefully cut into the surface, along the guide lines to connect the four pilot holes, cutting the installation hole out of the table’s surface. Installation Hole Installing the Module in the Modular Table Box Notes: Modules can be mounted using three different mounting depths depending on your conference table setup.
Notes: Before installing a Module into the Modular Table Box, connect each of the conference room devices to the bottom of the Module (see Connecting Devices to the Bottom of the Module or Connecting Devices to the Top of the Module sections in the Module’s User Manual). Connect the Universal Power Adapter to the bottom of the Module (see Powering the Module section in the Module’s User Manual). 2.
4. Align the Module with the Installation Holes on both sides of the Modular Table Box. 5. Insert the Module Screws (x 8, 4 per side) through the Installation Holes on the Modular Table Box and into the Mounting Holes on the Module. Note: The eight Module Screws are packaged with the Module. Inserting Module Screws To view manuals, videos, drivers, downloads, and more visit www.startech.
6. Using a Phillips Head Screwdriver, tighten the Module Screws. Be careful not to overtighten. Installing the Lacing Bar (Cable Organization) 1. On the Modular Table Box or Single Modular Table Box, align the Mounting Holes on the Lacing Bar with the Mounting Holes on the Modular Table Box. 2. Insert the Lacing Bar Screws (2 per side) through the Mounting Holes on the Lacing Bar and into the Modular Table Box. Note: The Modular Table Box has three Lacing Bar mounting options (left, center, and right).
3. Using a Phillips Head Screwdriver, tighten the Lacing Bar Screws. Be careful not to overtighten. 4. Using Cable Ties (sold separately), attach the cables connected to the Module(s) to the Lacing Bar. Note: The Lacing Bar is used for cable management and can help reduce cable strain, bend radius, unintentional cable disconnects and improve organization. Installing the Modular Table Box into a Surface 1.
3. Secure the Modular Table Box in place by tightening each of the Wing Fasteners until the top of the nut comes in contact with the bottom of the table’s surface, creating a tight seal between the table’s surface and the Modular Table Box. Be careful not to overtighten the Wing Fasteners. Modular Table Box To view manuals, videos, drivers, downloads, and more visit www.startech.
Assembling the Cable Management Module The Cable Management Module is used to organize up to 2 cables in the Modular Table Box. Assembly Requirements: • • • • • • • • • 1. 2. 3. 4. 5.
6. Align the other Cable Management Plate with the Plate Screw Holes and Bushing Holes on the top of the Cable Management Bracket. Insert 2 of the Plate Screws, through the Cable Management Plate and into the Cable Management Bracket. 7. Using the Phillips Head Screwdriver tighten the 2 Plate Screws, securing the Cable Management Plate in place. Be careful not to over tighten the Plate Screws. 8. Carefully push the Cable Bushings into the designated Bushing Holes, snapping them into place.
Technical Support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. For the latest drivers/software, please visit www.startech.com/downloads Warranty Information This product is backed by a two-year warranty. StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
