Flat-Screen TV Ceiling Mount - Short Pole - Full Motion FPCEILPTBSP *actual product may vary from photos FR: Guide de l’utilisateur - fr.startech.com DE: Bedienungsanleitung - de.startech.com ES: Guía del usuario - es.startech.com NL: Gebruiksaanwijzing - nl.startech.com PT: Guia do usuário - pt.startech.com IT: Guida per l’uso - it.startech.com For the latest information, technical specifications, and support for this product, please visit www.StarTech.com/FPCEILPTBSP.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols PHILLIPS® is a registered trademark of Phillips Screw Company in the United States or other countries. This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.
Warning statements Mensagens de aviso Make sure to assemble this product according to the instructions. Failure to do so might result in personal injury or property damage. Certifique-se de que monta este produto de acordo com as instruções. O incumprimento pode resultar em ferimentos pessoais ou danos de propriedade. Make sure that the weight of the monitor doesn’t exceed the weight capacity of this product.
Table of Contents Warnings....................................................................................................................................................... i Introduction.............................................................................................1 Product diagram......................................................................................................................................... 1 Product dimensions...................................................
Introduction Product diagram Ceiling mount and pole Extension pole Horizontal bracket Vertical bracket Vertical bracket Instruction manual 1
Product dimensions 200 mm 48 mm min 560 mm to max 910 mm -3° +3° 360° min 200 mm to max 600 mm 680 mm Instruction manual 2 435 mm 40 mm min 200 mm to max 400 mm min 778 mm to max 1128 mm -60° +60° 0° -25°
Technical specifications Type of measurement Measurement VESA mounting hole pattern 200x200 300x300 400x200 400x400 600x400 Rated load 50 kg (110 lb.) kg Tilt +00 to -250 Screen size Between 813 mm and 1905 mm (32 in. and 75 in.
Package contents 1 2 Ceiling mount and pole Extension pole Qty: One Qty: One 4 3 Horizontal bracket Vertical brackets Qty: One Qty: Two 5 Instruction manual 6 Bolts Nuts Qty: Two Qty: Two 4
8 7 Wrench Hex key Qty: One Qty: One 9 10 Mounting template M5x14 mm screws Qty: One Qty: Four 12 11 M6x14 mm screws M6x30 mm screws Qty: Four Qty: Four Instruction manual 5
13 14 M8x30 mm screws M8x50 mm screws Qty: Four Qty: Four 15 16 Rectangular washers Small spacers Qty: Four Qty: Eight 17 Instruction manual 18 Large spacers 6.
19 20 Concrete anchors Circular washers Qty: Four Qty: Four 21 Instruction manual Qty: One Requirements • A display or TV that is compatible with one of the VESA mounting hole patterns that FPCEILPTBSP supports • A Phillips screwdriver Requirements are subject to change. For the latest requirements, please visit www.StarTech.com/FPCEILPTBSP.
Installation Warning! Make sure that the weight of the TV does not exceed the weight capacity of this product. If you exceed the weight capacity, you might experience personal injury or damage to the product. This product can support the following weight: Up to 50 kg (110 lb.). Attach the ceiling mount and pole to the ceiling Warning! Ceiling structures vary, and it is important to make sure that the type of structure and mounting hardware that you are using will properly support the mounted equipment.
2. Follow the appropriate steps for the type of ceiling that you’re attaching the mount to and attach the ceiling mount and pole to the ceiling. 3. To adjust the vertical position of the pole, use the wrench and the hex key to adjust the nut at the side of the mounting base. (figure 2) figure 2 Ceiling mount and pole Hex key Wrench Attach the extension pole to the ceiling mount and pole 1. Place one end of the TV cable through the top hole in the ceiling mount and pole. 2.
3. Slide the extension pole into the ceiling mount and pole, until the extension pole is at the desired height. 4. Line up the holes on the extension pole with the holes on the ceiling mount and pole. 5. Insert the two bolts through the holes in the ceiling mount and pole and the extension pole. 6. Attach the two nuts to the bolts, and use the wrench and the hex key to tighten the nuts in place.
Attach the horizontal bracket 1. Use a wrench to remove the retainer nut from the back of the horizontal bracket. (figure 5) figure 5 Wrench Horizontal bracket Retainer nut 2. Loosen the two nuts at the back of the horizontal bracket. 3. Attach the horizontal bracket onto the mounting bracket at the end of the extension pole. 4. Reattach the retainer nut that you removed in step 1 and use a wrench to tighten the nut in place. (figure 6) 5. Tighten the two nuts that you loosened in step 2.
Prepare the vertical brackets 1. Use a screwdriver to remove the screw from the mounting hardware on each of the two vertical brackets. 2. Put the screws to the side; you will need to use them when you hang the TV. 3. Flip down the smaller piece of the mounting hardware.
Mount a TV with a flush mounting surface To accommodate different TV designs, the FPCEILPTBSP comes with five sets of screws of different lengths and diameters, and two sizes of spacers. 1. To select the combination of mounting hardware that you need to use to attach the vertical brackets to the TV, complete the following: • Determine the depth of the mounting holes on the TV. • Determine the diameter of the mounting holes on the TV.
Mount a TV with a recessed mounting surface To accommodate different TV designs, the FPCEILPTBSP comes with five sets of screws of different lengths and diameters, and two sizes of spacers. 1. To select the combination of mounting hardware that you need to use to attach the vertical brackets to the TV, complete the following: • Determine the depth of the mounting holes on the TV. • Determine the diameter of the mounting holes on the TV.
2. Line up the vertical brackets with the mounting holes on the back of the TV. 3. Place the rectangular washers over the vertical brackets. 4. Insert the M6x30 mm screws, M8x30 mm screws, or M8x50 screws through the washers, vertical brackets, spacers, and into the back of the monitor. 5. Use a Phillips screwdriver to tighten the screws. (figure 9) Warning! Do not over-tighten the screws. If you encounter resistance while you’re tightening the screws, stop tightening.
Attach the TV to the horizontal bracket Warning! Make sure that the weight of the TV doesn’t exceed the weight capacity of this product. If you exceed the weight capacity, you might experience personal injury or damage to the product. This product can support the following weight: Up to 50 kg (110 lb.) Warning! Attaching the monitors is a two-person job. Do not attempt to complete this task by yourself. 1.
2. Flip up the mounting hardware and reinsert the screws that you removed from the mounting hardware on each of the vertical brackets. (figure 11) 3. Use a Phillips screwdriver to tighten the screws in place.
4. Make any necessary adjustments to the angle of the TV.
Technical support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. For the latest drivers/software, please visit www.startech.com/downloads Warranty information This product is backed by a five-year warranty. StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.