Flat-Screen TV Wall Mount - Low Profile - Fixed - Anti-Theft FPWFXBAT *actual product may vary from photos FR: Guide de l’utilisateur - fr.startech.com DE: Bedienungsanleitung - de.startech.com ES: Guía del usuario - es.startech.com NL: Gebruiksaanwijzing - nl.startech.com PT: Guia do usuário - pt.startech.com IT: Guida per l’uso - it.startech.com JP: 取扱説明書 - jp.startech.com For the latest information, technical specifications, and support for this product, please visit www.StarTech.com/FPWFXBAT.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols PHILLIPS® is a registered trademark of Phillips Screw Company in the United States or other countries. This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.
Warning statements Mensagens de aviso Make sure to assemble this product according to the instructions. Failure to do so might result in personal injury or property damage. Certifique-se de que monta este produto de acordo com as instruções. O incumprimento pode resultar em ferimentos pessoais ou danos de propriedade. Make sure that the weight of the TV doesn’t exceed the weight capacity of this product. If you exceed the weight capacity, you might experience personal injury or damage to the equipment.
Table of Contents Warnings....................................................................................................................................................... i Introduction.............................................................................................1 Product dimensions.................................................................................................................................. 1 Product diagram..........................................................
Introduction Product dimensions 22 mm 985 mm 248 mm min 75 mm to max 404 mm 440 mm min 300 mm to max 810 mm 29 mm Product diagram Decorative cover Wall mount Level Decorative cover Safety bar Adapter bracket Adapter bracket Instruction manual 1
Technical specifications Unless otherwise indicated, the technical specifications in the table below apply to the TV or display. Type of measurement Measurement VESA mounting hole pattern on the TV mount 300x300 400x200 400x400 600x400 800x400 Weight capacity of TV mount 40 kg (88 lb.) kg Screen size Between 762 mm and 1905 mm (30 in. and 75 in.
Package contents 1 2 Wall mount Safety bar Qty: One Qty: One 4 3 Adapter brackets Level Qty: Two Qty: One 5 6 Decorative covers Decorative cover screws Qty: Two Qty: Four Instruction manual 3
7 M5x14 mm screws M6x14 mm screws Qty: Four Qty: Four 9 10 M6x30 mm screws M8x30 mm screws Qty: Four Qty: Four 12 11 M8x50 mm screws Rectangular washers Qty: Four Qty: Four Instruction manual 4
13 14 Large spacers Small spacers Qty: Eight Qty: Eight 15 16 Circular washers Screws Qty: Six Qty: Six 17 18 Concrete anchors Instruction manual Qty: Six Qty: One Instruction manual 5
Requirements • A display or TV that is compatible with one of the VESA mounting hole patterns FPWFXBAT supports • A Phillips screwdriver • A padlock if you want to secure the display or TV Requirements are subject to change. For the latest requirements, please visit www.StarTech.com/FPWFXBAT.
Installation Attach the decorative covers 1. Place a decorative cover over one end of the wall mount. 2. On the back of the wall mount, insert a decorative cover screw through the top hole in the wall mount and into the decorative cover. Tip! There are arrows on the front of the wall mount to indicate which side is the front. 3. Insert another decorative cover screw through the bottom hole in the wall mount and into the decorative cover. (figure 1) 4. Use a Phillips screwdriver to tighten the screws. 5.
Attach the wall mount to the wall Warning! The wall mount is designed to be installed on a wood stud, solid concrete, or cinder block wall. The wall structure should be capable of supporting at least four times the weight of the mounted equipment. The mounting hardware included with this product may not be adequate for installation on certain wall structures.
figure 4 Instruction manual 9
Attach the adapter brackets to a flush mounting surface To accommodate different TV designs, the FPWFXBAT comes with five sets of screws of different lengths and diameters, washers with two hole sizes, and two sizes of spacers. 1. To select the combination of mounting hardware that you need to use to attach the adapter brackets to the TV, complete the following: • Determine the depth of the mounting holes on the TV. • Determine the diameter of the mounting holes on the TV.
3. Line up the adapter brackets with the mounting holes on the back of the TV. 4. Place the rectangular washers over the adapter brackets. 5. Insert the M5x14 mm screws or M6x14 mm screws through the rectangular washers, adapter brackets, and into the back of the TV. 6. Use a Phillips screwdriver to tighten the screws. (figure 6) Warning! Do not over-tighten the screws. If you encounter resistance while you’re tightening the screws, stop tightening. Failure to do so could result in damage to the TV.
Attach the adapter brackets to a recessed mounting surface To accommodate different TV designs, the FPWFXBAT comes with five sets of screws of different lengths and diameters, washers with two hole sizes, and two sizes of spacers. 1. To select the combination of mounting hardware that you need to use to attach the adapter brackets to the TV, complete the following: • Determine the depth of the mounting holes on the TV. • Determine the diameter of the mounting holes on the TV. 2.
3. Position the adapter brackets so that the arrows on the flat side of the adapter brackets are pointing towards the top of the TV and the nuts on the adapter brackets are pointing towards the outside edges of the TV.
4. Line up the adapter brackets with the mounting holes on the back of the TV. 5. Place the rectangular washers over the adapter brackets. 6. Insert the M6x30 mm screws, M8x30 mm screws, or the M8x50 mm screws through the rectangular washers, adapter brackets, spacers, and into the back of the TV. 7. Use a Phillips screwdriver to tighten the screws. (figure 8) Warning! Do not over-tighten the screws. If you encounter resistance while you’re tightening the screws, stop tightening.
Hook the TV onto the wall mount Warning! Make sure that the weight of the TV doesn’t exceed the weight capacity of this product. If you exceed the weight capacity, you might experience personal injury or damage to the product. This product can support the following weight: Up to 40 kg (88 lb.) Warning! Attaching the TV is a two-person job. Do not attempt to complete this task by yourself.
Attach the safety bar 1. Slide the safety bar into the groove in the adapter brackets.
2. To prevent someone from removing the safety bar, attach a padlock (not provided) to the hole in the end of the safety bar.
Technical support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. For the latest drivers/software, please visit www.startech.com/downloads Warranty information This product is backed by a five-year warranty. StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
