2U Hinged Wall-Mount Rack Enclosure Actual product may vary from photos User Manual SKU#: RK1232WALHM For the latest information and specifications visit www.startech.
Compliance Statements FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Safety Statements Safety Measures • Wiring terminations should not be made with the product and/or electric lines under power. • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines. • Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.
Säkerhetsåtgärder • Montering av kabelavslutningar får inte göras när produkten och/eller elledningarna är strömförda. • Installation och/eller montering får endast göras av behöriga yrkespersoner och enligt gällande lokala förordningar för säkerhet och byggnormer. • Kablar (inklusive elkablar och laddningskablar) ska dras och placeras på så sätt att risk för snubblingsolyckor och andra olyckor kan undvikas. Warning Statements • Make sure that you assemble this product according to the instructions.
• • • • för att det välter. Förläng inte fler än en komponent från skåpet för att undvika risk. Placera inte saker ovanpå skåpet och ställ inte skåpet ovanpå ett annat skåp. Håll vätskor borta från skåpet. Se till att du installerar skåpet på en plats som kan hantera den kombinerade vikten av skåpet och utrustningen som du tänker placera inuti. Produkten behöver en jordad anslutning. Använd inte produkten utan en jordad anslutning. Avertissements • Assemblez ce produit conformément aux instructions.
• • • • erhöht die Chance, dass das Gehäuse umkippt. Um dies zu vermeiden, ziehen Sie niemals mehr als eine Komponente aus diesem Gehäuse aus. Platzieren Sie keine Gegenstände auf dem Gehäuse und stapeln Sie das Gehäuse nicht auf einem anderen Gehäuse. Halten Sie Flüssigkeiten von diesem Gehäuse fern. Vergewissern Sie sich, dass der Untergrund, auf dem das Gehäuse aufgestellt wird, in der Lage ist, das Gesamtgewicht des Gehäuses und der Geräte, die Sie darin platzieren möchten, zu tragen.
• Perigo de queda! Estender vários componentes desta caixa aumenta a probabilidade desta caixa cair. Para evitar este risco, não expandir mais de um componente desta caixa. • Não colocar nenhum artigo nesta caixa e não empilhar a caixa em cima de outra caixa. • Manter líquidos afastados desta caixa. • Certifique-se de que instala a caixa numa área que pode suportar o peso combinado da caixa e o equipamento que pretende colocar dentro da caixa. • Este produto requer uma ligação à terra.
of op te tillen zonder hulp. • Kantelgevaar! Wanneer meerdere componenten uit deze behuizing steken, bestaat de kans dat deze zal kantelen. Om dit risico te voorkomen, mag niet meer dan één component uit de behuizing steken. • Plaats geen voorwerpen op deze behuizing en stapel de behuizing niet op een andere behuizing. • Houd vloeistof uit de buurt van deze behuizing.
Table of Contents Compliance Statements.........................................................................1 Safety Statements...................................................................................2 Warning Statements...............................................................................3 Product Diagram.....................................................................................9 Product Information............................................................................
Product Diagram 5 5 6 7 8 6 8 2 4 1 7 3 1 Front Door 5 Cable Access Cover 2 Rear Door 6 Cable Access Opening 3 Horizontal Mounting Rail 7 Side Panel 4 Vertical Mounting Rail 8 Vent To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Product Information Package contents • • • • • • • • Wall-mount enclosure x 1 1U shelf x 1 Roll of hook-and-loop fastener x 1 12-24 cage nuts x 48 12-24 screws x 48 Door keys x 2 Side panel keys x 2 Instruction manual x 1 Requirements Phillips type screwdriver • Appropriate tools and mounting hardware for the type of wall you’re using Requirements are subject to change. For the latest requirements, please visit www.StarTech.com/RK1232WALHM.
Ground the Enclosure Warning! This product must be grounded. Do not use this product without an earth ground connection. 1. Use an M6 screw to attach a grounding wire to the front or rear grounding point on the enclosure. 2. Route the wire under the frame of the enclosure and connect the wire to your facility’s earth ground connection. Grounding Wire To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Lock or unlock the front or rear door For additional security, the front and rear door of the enclosure can be locked with the provided door keys. • To lock or unlock the front or rear door of the enclosure, insert one of the provided door keys in the lock on the door and turn the key clockwise or counterclockwise. Remove the side panels 1. If the side panels are locked, use the provided side panel keys to unlock the panels. 2. Pull the two tabs on the side panel towards the center of the panel.
3. While using proper lifting techniques, remove the side panel from the enclosure. Removing the Side Panel from the Enclosure 4. Repeat steps 1 to 3 to remove the other side panel. Installing the Side Panels To put the side panels back on the enclosure: 1. Place one of the side panels in the groove at the bottom of the enclosure. 2. Pull the two tabs on the side panel towards the center of the panel, push the top part of the side panel into the enclosure, and release the tabs.
3. Use one of the provided side panel keys to lock the side panel. Access your cables There are two cable access covers on the enclosure that you can remove to access and manage your cables. 1. To take off a cable access cover, use a Phillips type screwdriver to remove the two screws on both ends of the cable access cover. 2. Pull the cable access cover away from the enclosure. (figure 4) Removing the Cable Covers To view manuals, videos, drivers, downloads, technical drawings, and more visit www.
Replacing the Cable Covers To put the cable access cover back on: 1. Place the cover over the cable access opening 2. Use a Phillips type screwdriver to insert the screws through the cover and into the enclosure. 3. Tighten the screws. Reverse the front door To accommodate different rack configurations, you can reverse the front door of the enclosure so that it opens to the left or right of the enclosure. 1.
Door Release Levers 3. Flip the front door so that the levers are located on the opposite side. 4. Position the front door so that the top and bottom levers are aligned with the washers located in the hinge area of the enclosure. 5. In the top corner of the front door, pull the lever down and release it into the washer and hole in the enclosure. 6. In the bottom corner of the front door, pull the lever up and release it into the washer and hole in the enclosure.
Adjust the depth of the mounting rails The mounting rails come pre installed in the enclosure. Both the front and back set of mounting rails can be adjusted independently in 3/4 inch (20 mm) increments. Warning! Do not attempt to adjust the mounting rails when equipment is installed in the enclosure. Remove the equipment first before you adjust the mounting rails. 1. Each of the mounting rails is connected to the enclosure with a screw and cage nut in the upper and lower corners of the mounting rail.
Mount the enclosure to the wall Warning! Remove all equipment from the enclosure before you attempt to mount the enclosure to the wall. Wall structures vary and it is important to make sure that the type of wall structure and mounting hardware that you are using will properly support the mounted equipment. Failure to do so might result in personal injury and/or equipment damage. The wall structure should be capable of supporting at least four times the weight of the mounted equipment.
Install equipment Warning! Do not add equipment to the enclosure until the enclosure is securely attached to the wall. When you load equipment into this enclosure, load the heaviest equipment in the bottom section of this enclosure first. Continue loading equipment in a descending order of weight, so that the lighter equipment is installed in the upper sections of this enclosure and the heavier items are on the bottom.
Warranty Information This product is backed by a two-year warranty. For further information on product warranty terms and conditions, please refer to www.startech.com/warranty. Limitation of Liability In no event shall it be the liability of StarTech.com Ltd. and StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
