5U Knock-Down Server Rack Cabinet with Casters | 32 in. Deep Actual product may vary from photos User Manual SKU#: RK1536BKF For the latest information and specifications visit www.startech.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question.
Warning Statements • Make sure that you assemble this product according to the instructions. • Do not exceed the weight capacity of this product. Overloading this product might result in injury or property damage. This product can support the following weight: Stationary = 1763.7 lb. (800 kg) Rolling = 330 lb. (150 kg). • This product is intended for indoor use only and should not be used outdoors. • This enclosure is extremely heavy. Never attempt to move or lift this enclosure without assistance.
• Produkten behöver en jordad anslutning. Använd inte produkten utan en jordad anslutning. Avertissements • Assemblez ce produit conformément aux instructions. • Ne dépassez pas la capacité pondérale de ce produit. Une surcharge de ce produit peut entraîner des dommages corporels ou matériels. Ce produit peut supporter le poids suivant, stationnaire = 800 kg, roulant = 150 kg. • Ce produit est uniquement destiné à une utilisation en intérieur et ne doit pas être utilisé à l’extérieur.
• Platzieren Sie keine Gegenstände auf dem Gehäuse und stapeln Sie das Gehäuse nicht auf einem anderen Gehäuse. • Halten Sie Flüssigkeiten von diesem Gehäuse fern. • Vergewissern Sie sich, dass der Untergrund, auf dem das Gehäuse aufgestellt wird, in der Lage ist, das Gesamtgewicht des Gehäuses und der Geräte, die Sie darin platzieren möchten, zu tragen. • Dieses Produkt erfordert einen Schutzleiteranschluss. Verwenden Sie das Produkt nicht ohne einen Schutzleiteranschluss.
• Perigo de queda! Estender vários componentes desta caixa aumenta a probabilidade desta caixa cair. Para evitar este risco, não expandir mais de um componente desta caixa. • Não colocar nenhum artigo nesta caixa e não empilhar a caixa em cima de outra caixa. • Manter líquidos afastados desta caixa. • Certifique-se de que instala a caixa numa área que pode suportar o peso combinado da caixa e o equipamento que pretende colocar dentro da caixa. • Este produto requer uma ligação à terra.
• Dit product is alleen bedoeld voor binnengebruik en mag niet buiten worden gebruikt. • Deze behuizing is enorm zwaar. Probeer nooit deze behuizing te verplaatsen of op te tillen zonder hulp. • Kantelgevaar! Wanneer meerdere componenten uit deze behuizing steken, bestaat de kans dat deze zal kantelen. Om dit risico te voorkomen, mag niet meer dan één component uit de behuizing steken. • Plaats geen voorwerpen op deze behuizing en stapel de behuizing niet op een andere behuizing.
設置して下さい。 • この製品にはアースが必要です。 アース接続をしていない状態で本製品 を使用しないでください。 To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Safety Statements Safety Measures • Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.
Table of Contents Warning Statements...............................................................................2 Safety Statements...................................................................................8 Product Diagram.....................................................................................10 Front View..................................................................................................................................................... 10 Product Dimensions........
Product Diagram Front View 1 2 8 3 4 7 5 6 1 Top Panel 5 Caster/Leveling Feet 2 Plastic Corner Caps 6 Bottom Panel 3 Center Beam 7 Side Panel 4 Front Door 8 Rear Door To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Product Dimensions Front To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Side To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Product Information Package Contents • • • • • • • • • • • • • • • • • • • • • • Side Panels x 2 Center Beams x 4 Bottom Panels w/ Cable Management Slot x 2 Bottom Panel x 1 Front Door x 1 Rear Door x 1 Plastic Corner Caps x 8 M8 x 20 mm Hex Screws x 8 M8 Spring Washers x 8 M4 x 10 mm Flat Head Screws x 8 M6 x 12 mm Hex Screws x 4 M5 x 12 mm Screws x 6 M6 Hex Key x 1 M8 Hex Key x 1 M6 x 12 mm Phillips Screws x 24 M6 Cage Nuts x 24 M6 Plastic Cap Washers x 24 Casters x 2 Caster w/Brakes x 2 M6 x 10 mm Phill
• • • Side Panel Keys x 2 Phillips Head Screwdriver x 1 Door Hinge Pin x 2 Requirements • • • Spirt/Bubble Level x 1 14 mm Wrench x 1 (Optional) Cage Nut Tool x 1 To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Assembling the Server Rack 1. Align the Screw Holes on the corners of the Side Panel with the Screw Holes on the ends of the Center Beam. Ensure that the Lip on the Center Beams lines up with the Lip on the inner side of the Side Panel. 2. Slide an M8 Spring Washer over the M8 x 20 mm Hex Screw. 3. Insert the M8 x 20 mm Hex Screws through the Screw Hole on the Side Panel and into the Screw Holes on the Center Beam. 4.
11. Align the Leveling Feet with the Pre-Threaded Holes on the bottom of the Server Rack Frame. 12. Using a 14 mm Wrench, tighten the Leveling Feet so that the four Leveling Feet are all at the same height and are shorter than the height of the Casters. 13. Align the Notch in the Plastic Corner Caps (x 4) with the Screw Hole on each of the corners on the Server Rack. 14. Insert an M4 x 10 mm Flat Head Screw through the Screw Holes in the Plastic Corner Cap and into the Screw Hole on the Server Rack.
20. Align the Screw Holes on the Bottom Plate w/ Cable Management Slot with the Screw Holes on the interior of the Side Panel, located on the front and back on the Side Panel. 21. Insert two M6 x 12 mm Phillips Screws through the Screw Holes on the Bottom Plate w/ Cable Management Slot and into the Screw Holes on the interior of the Side Panel. 22. Using a Phillips Head Screwdriver, tighten the M6 x 12 mm Phillips Screws, being careful not to over-tighten. 23.
29. Angle the bottom corner of the Front Door towards the Door Hinge Pin. 30. Insert the Door Hinge Pin into the bottom Hinge Pin Hole on the Front Door. 31. In the top corner on the Front Door, pull the Spring- Loaded Hinge Pin down. 32. While holding down the Spring-Loaded Hinge Pin, angle the top corner of the Front Door towards the top corner of the Server Rack, aligning the Spring-Loaded Hinge Pin with the Hinge Pin Hole. 33. Release the Spring-Loaded Hinge Pin into the Hinge Pin Hole. 34.
2. Using an 14 mm Open-Ended Wrench, lower the Leveling Feet (4 located next to each Casters) by turning it clockwise until the base of the Leveling Feet are tightly pressed against the surface, supporting the weight of the Server Rack. Grounding the Enclosure Note: This product must be grounded. Do not use this product without an earth ground connection. 1.
1. Decide where in the Server Rack you want to install the equipment and insert the M6 Cage Nuts in the Mounting Rails. 2. Line up the Mounting Holes on the equipment with the M6 Cage Nuts. 3. Insert the Screws through the Mounting Holes on the equipment and into the M6 Cage Nuts. 4. Using a Phillips Head Screwdriver tighten the Screws, being careful not to over-tighten. Adjusting the Mounting Rails 1. Each Mounting Rail has four M6 Screws securing the Mounting Rail to two Depth Adjustment Rails.
5. Insert the Cage Nuts into the Square Mounting Holes on the Depth Adjustment Rails. Insert one side of the Cage Nut into the Square Mounting Hole and push the other side into the Square Mounting Hole, until it locks into place. Note: Use a Cage Nut Tool if you are having issues installing the Cages Nuts into the Depth Adjustment Rails. 6. Insert the M6 Screws through the Mounting Rail and into the Depth Adjustment Rails. 7. Using a Phillips Head Screwdriver to tighten the M6 Screws.
Warranty Information This product is backed by a lifetime warranty. For further information on product warranty terms and conditions, please refer to www.startech.com/warranty. Limitation of Liability In no event shall the liability of StarTech.com Ltd. and StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
