6U Wall-Mount Rack Enclosure Actual product may vary from photos User Manual SKU#: RK616WALM For the latest information and specifications visit www.startech.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question.
Warning Statements Read the entire manual and make sure that you understand the instructions before you start to assemble and use this product. Wall structures vary, and it is important to make sure that the type of wall structure and mounting hardware that you are using will properly support the mounted equipment. Failure to do so might result in personal injury and/or equipment damage. The wall structure should be capable of supporting at least four times the weight of the mounted equipment.
utrustningen. Om du inte gör det kan skada på person och/eller utrustning uppstå. Väggstrukturen ska kunna klara av minst fyra gånger vikten av den monterade utrustningen. Detta skåp är extremt tungt. Försök aldrig flytta på skåpet eller lyfta det utan hjälp. Risk för vältning! Att förlänga flera komponenter från detta skåp ökar risken för att det välter. Förläng inte fler än en komponent från skåpet för att undvika risk. Placera inte saker ovanpå skåpet och ställ inte skåpet ovanpå ett annat skåp.
Plaats geen voorwerpen op deze behuizing en stapel de behuizing niet op een andere behuizing. Houd vloeistof uit de buurt van deze behuizing. Zorg dat u de behuizing installeert op een plaats die geschikt is voor het gecombineerde gewicht van de behuizing en de apparatuur die u in de behuizing wilt plaatsen. Dit product vereist een geaarde verbinding. Gebruik dit product niet zonder een geaarde verbinding.
この製品にはアースが必要です。 アース接続をしていない状態で本製品を使 用しないでください。 本製品に装置を積載する前に、組み立て、設置、壁面への取り付けが適切に行 われているか確認して下さい。 本製品に装置を積載する際は、最初に最も重い装置を一番下のセクションに 入れて下さい。重い装置から順に積載し、重いものが下のセクション、軽いも のが上のセクションに配置されるようにして下さい。 Dichiarazioni di avvertenza Leggere l’intero manuale e assicurarsi di aver compreso tutte le istruzioni prima di iniziare ad assemblare e a utilizzare questo prodotto. La struttura dei muri può variare.
l’operazione in ordine decrescente di peso, in modo che le apparecchiature più leggere siano installate nelle parti superiori del prodotto e quelle più pesanti nella parte inferiore. Avertissements Assemblez ce produit conformément aux instructions. Lisez tout le manuel et assurez-vous que vous comprenez les instructions avant de commencer à assembler et utiliser ce produit. Les structures des murs varient.
Mensagens de aviso Leia todo o manual e certifique-se de que entende as instruções antes de começar a montar e a utilizar este produto. As estruturas de parede variam e é importante certificar-se de que o tipo de estrutura de parede e hardware de montagem que está a usar irá suportar devidamente o equipamento montado. O incumprimento pode resultar em ferimentos pessoais e/ou danos no equipamento. A estrutura de parede deve ser capaz de suportar pelo menos quatro vezes o peso do equipamento montado.
montaje que se va a utilizar para soportar debidamente el equipo. De lo contrario, se pueden producir lesiones personales o daños del equipo. La estructura de la pared debe ser capaz de soportar al menos cuatro veces el peso del equipo instalado. La caja es extremadamente pesada. Nunca intente mover o alzar esta caja sin la debida asistencia de otra persona. ¡Peligro de vuelco! Añadir a esta caja varios componentes aumenta las posibilidades de peligro de vuelco de la caja.
Hilfe zu bewegen oder anzuheben. Kippgefahr! Das Ausziehen mehrerer Komponenten aus diesem Gehäuse erhöht die Chance, dass das Gehäuse umkippt. Um dies zu vermeiden, ziehen Sie niemals mehr als eine Komponente aus diesem Gehäuse aus. Platzieren Sie keine Gegenstände auf dem Gehäuse und stapeln Sie das Gehäuse nicht auf einem anderen Gehäuse. Halten Sie Flüssigkeiten von diesem Gehäuse fern.
Table of Contents Warning Statements...............................................................................2 Product Diagram.....................................................................................11 Product Information ..............................................................................12 Package Contents...................................................................................................................................... 12 Requirements.........................
Product Diagram 7 6 4 5 2 3 1 2 8 5 3 4 1 Front Door 5 Cable Access Openings (x 2) 2 Side Panels (x 2) 6 Mounting Plate 3 Vents 7 Top Panel 4 Cable Access Covers (x 2) 8 Bottom Panel To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Product Information Package Contents • • • • • • • • • Wall-Mount Enclosure x 1 1U Shelf (CABSHELFV1U) x 1 Roll of Hook-and-Loop Fastener x 1 12-24 Cage Nuts x 24 12-24 Screws x 24 Door Keys x 2 Side Panel Keys x 2 Cup Washers x 24 User Manual x 1 Requirements • • Phillips™ type screwdriver Appropriate tools and mounting hardware for the type of wall you’re using Note: The images in this manual depict RK920WALM. This product features a different rack height and depth, and has two posts instead of four.
Grounding the Wall-Mount Enclosure Warning! This product must be grounded. Do not use this product without an earth ground connection. 1. Use an M6 Screw to attach a Grounding Wire to the front or rear Grounding Point on the Wall-Mount Enclosure. Installing the Grounding Wire 2. Route the Grounding Wire under the frame of the WallMount Enclosure and connect the Grounding Wire to your facility’s earth ground connection. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.
Locking or Unlocking the Front Door • To lock or unlock the front door of the enclosure, insert one of the provided Door Keys in the Lock on the Front Door on the Wall-Mount Enclosure and turn the key clockwise or counterclockwise. Removing the Side Panels 1. If the Side Panels are locked, use one of the provided Side Panel Keys to unlock the Side Panels. 2. Pull the two Tabs on the Side Panel towards the center of the panel.
3. While pulling the two Tabs, lift the Side Panel free from the Wall-Mount Enclosure. Be careful and use proper lifting techniques when removing the Side Panels from the WallMount Enclosure. 4. Repeat steps 1 to 3 to remove the other Side Panel. Replacing the Side Panels 1. Place one of the Side Panels in the groove at the bottom of the Wall-Mount Enclosure. 2. Pull the two Tabs on the Side Panel towards the center of the panel. 3.
2. Pull the Cable Access Cover away from the Wall-Mount Enclosure. Removing the Cable Access Cover Replacing the Cable Access Cover 1. Align the Cable Access Cover with the Cable Access Opening. 2. Use a Phillips Head Screwdriver to insert the four Screws through the Cable Access Cover and into the Wall-Mount Enclosure. 3. Tighten the Screws, being careful not to over-tighten. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Reversing the Front Door To accommodate different rack configurations, you can reverse the Front Door of the Wall-Mount Enclosure so that it opens to the left or right of the Wall-Mount Enclosure. The Front Door is attached to the Wall-Mount Enclosure with Levers that are located at the top and bottom of the Front Door. 1. In the top corner of the inside of the Front Door, pull the lever down and move the top corner of the Front Door away from the Wall-Mount Enclosure. 2.
5. In the top corner of the Front Door, pull the Lever down and release it into the washer and hole in the Wall-Mount Enclosure. 6. In the bottom corner of the Front Door, pull the Lever up and release it into the washer and hole in the Wall-Mount Enclosure. Adjust the Depth of the Mounting Rails The Mounting Rails come pre installed in the Wall-Mount Enclosure. The Mounting Rails can be adjusted independently in 3/4 inch (20 mm) increments to accommodate different sizes of equipment.
Adjusting the Mounting Rails Use the Mounting Rail Tapped Holes The Mounting Rails come pre installed with the Cage Nut Holes facing outward. However, the Mounting Rails can be adjusted so that you can use the Tapped Holes to install your equipment. Warning! Remove all equipment before adjusting the Mounting Rails. 1. Use a Phillips Head Screwdriver to remove the Screw and Cage Nut located in the upper and lower corners of the Mounting Rails. 2.
Flipping the Mounting Rails 3. To reattach the Mounting Rails to the Wall-Mount Enclosure, use a Phillips Head Screwdriver to install and tighten the screws that you removed in step 1. Mount the Enclosure to the Wall Warnings! Remove all equipment from the enclosure before you attempt to mount the enclosure to the wall. Wall structures vary and it is important to make sure that the type of wall structure and mounting hardware that you are using will properly support the mounted equipment.
If you lack the necessary expertise to attach this product to the wall that you’re using, contact a construction professional to install the enclosure or to provide specific mounting instructions for your wall structure. 1. Follow the appropriate steps for the type of wall that you’re attaching the Wall-Mount Enclosure to and attach the Mounting Plate to the Wall. 2. Hang the Wall-Mount Enclosure onto the Mounting Plate.
2. Line up the Mounting Holes on the equipment with the Cage Nuts. 3. Insert the Screws through the Mounting Holes on the equipment and into the Cage Nuts. 4. Tighten the Screws being careful not to over-tighten. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Warranty Information This product is backed by a five-year warranty. For further information on product warranty terms and conditions, please refer to www.startech.com/warranty. Limitation of Liability In no event shall the liability of StarTech.com Ltd. and StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
