9U Wall-Mount Rack Enclosure RK920WALM *actual product may vary from photos FR: Guide de l’utilisateur - fr.startech.com DE: Bedienungsanleitung - de.startech.com ES: Guía del usuario - es.startech.com NL: Gebruiksaanwijzing - nl.startech.com PT: Guia do usuário - pt.startech.com IT: Guida per l’uso - it.startech.com For the latest information, technical specifications, and support for this product, please visit www.StarTech.com/RK920WALM.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question.
Warning statements 注意 Make sure that you assemble this product according to the instructions. 必ず取扱説明書に従って本製品の組み立てを行って下さい。 Read the entire manual and make sure that you understand the instructions before you start to assemble and use this product. 最初に取扱説明書を最後まで読み、本製品の組み立て方をすべて理解してから組み立て作業を 始めて下さい。 Wall structures vary, and it is important to make sure that the type of wall structure and mounting hardware that you are using will properly support the mounted equipment.
Mensagens de aviso Certifique-se de que monta este produto de acordo com as instruções. Leia todo o manual e certifique-se de que entende as instruções antes de começar a montar e a utilizar este produto. As estruturas de parede variam e é importante certificar-se de que o tipo de estrutura de parede e hardware de montagem que está a usar irá suportar devidamente o equipamento montado. O incumprimento pode resultar em ferimentos pessoais e/ou danos no equipamento.
Table of Contents Warnings....................................................................................................................................................... i Introduction.............................................................................................1 Product diagram......................................................................................................................................... 1 Product dimensions...................................................
Introduction Product diagram 4 6 7 5 3 2 2 1 8 5 3 4 1 Front door 2 Side panel 3 Vents 4 Cable access cover 5 Cable access opening 6 Mounting plate 7 Top panel 8 Bottom panel Instruction manual 1
Product dimensions Top and bottom panels 65 mm 270 mm 30 mm 550 mm 600 mm Front door Side panels 550 mm 600 mm 503.65 mm 503.65 mm Enclosure Back of enclosure 70 mm 600 mm 406.5 mm 406.5 mm 503.65 mm 503.
Package contents • 1 x wall-mount enclosure • 1 x 1U shelf • 1 x roll of hook-and-loop fastener • 36 x 12-24 cage nuts • 36 x 12-24 screws • 2 x door keys • 2 x side panel keys • 1 x instruction manual Requirements • Phillips™ type screwdriver • Appropriate tools and mounting hardware for the type of wall you’re using Requirements are subject to change. For the latest requirements, please visit www.StarTech.com/RK920WALM. Note: The images in this manual depict RK9WALM.
Ground the enclosure Warning! This product must be grounded. Do not use this product without an earth ground connection. 1. Use an M6 screw to attach a grounding wire to the front or rear grounding point on the enclosure. 2. Route the wire under the frame of the enclosure and connect the wire to your facility’s earth ground connection.
Lock or unlock the front door • To lock or unlock the front door of the enclosure, insert one of the provided door keys in the lock on the door and turn the key clockwise or counterclockwise. Remove the side panels 1. If the side panels are locked, use the provided side panel keys to unlock the panels. 2. Pull the two tabs on the side panel towards the center of the panel.
3. Lift the side panel free from the enclosure. (figure 3) 4. Repeat steps 1 to 3 to remove the other side panel. figure 3 To put the side panels back on the enclosure, place one of the side panels in the groove at the bottom of the enclosure. Pull the two tabs on the side panel towards the center of the panel, push the top part of the side panel into the enclosure, and release the tabs. Use one of the provided side panel keys to lock the side panel.
Access your cables Both the top and bottom panels of the enclosure have cable access covers that you can remove to access and manage your cables. 1. To take off a cable access cover, use a Phillips type screwdriver to remove the two screws on both ends of the cable access cover. 2. Pull the cable access cover away from the enclosure.
Reverse the front door To accommodate different rack configurations, you can reverse the front door of the enclosure so that it opens to the left or right of the enclosure. The front door of the enclosure is attached to the enclosure with levers that are located at the top and bottom of the front door. 1. In the top corner of the inside of the front door, pull the lever down and move the top corner of the front door away from the enclosure. 2.
3. Flip the front door so that the levers are located on the opposite side. 4. Position the front door so that the top and bottom levers are aligned with the washers located in the hinge area of the enclosure. 5. In the top corner of the front door, pull the lever down and release it into the washer and hole in the enclosure. 6. In the bottom corner of the front door, pull the lever up and release it into the washer and hole in the enclosure.
Adjust the depth of the mounting rails The mounting rails come preinstalled in the enclosure. Both the front and back sets of mounting rails can be adjusted independently in 3/4 inch (20 mm) increments to accommodate different sizes of equipment. Warning! Do not attempt to adjust the mounting rails when equipment is installed in the enclosure. Remove the equipment first before you adjust the mounting rails. 1.
Use the mounting rail tapped holes The mounting rails come preinstalled in the enclosure but you can adjust the mounting rails so that you can use the tapped holes to install your equipment. Warning! Do not attempt to adjust the mounting rails when equipment is installed in the enclosure. Remove the equipment first before you adjust the mounting rails. 1. Each of the mounting rails is connected to the enclosure with a screw and cage nut in the upper and lower corners of the mounting rail.
Mount the enclosure to the wall Warning! Remove all equipment from the enclosure before you attempt to mount the enclosure to the wall. Warning! Wall structures vary and it is important to make sure that the type of wall structure and mounting hardware that you are using will properly support the mounted equipment. Failure to do so might result in personal injury and/or equipment damage. The wall structure should be capable of supporting at least four times the weight of the mounted equipment.
Install equipment Warning! Do not add equipment to the enclosure until the enclosure is securely attached to the wall. Warning! When you load equipment into this product, load the heaviest equipment in the bottom rails first. Continue loading equipment in a descending order of weight, so that the lighter equipment is installed in the upper sections of this enclosure and the heavier items are on the bottom.
Technical support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. For the latest drivers/software, please visit www.startech.com/downloads Warranty information This product is backed by a five-year warranty. StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.