User Guide

Erase a Drive
Warning! Backup data prior to erasing any drives.
1. Navigate to Erase Mode and press the Enter Button.
Warning! Do not disconnect the drive until erase process has completed. Doing so
may result in damage to the drive or lost data.
2. When the Green LED Indicator is no longer ashing and has become solid the
erasing process is complete.
Erase and Copy Modes
Mode Denition
Erase modes
Quick erase The partition table is quickly erased
Full erase Erases entire device(s), complying with NIST 800-88
Standards
3 Pass This method erases the drive three times. The rst time
with zeros, the second time with ones, and the third time
with random characters
Secure Erase Erases the non-loadable areas complying with NIST 800-88
Standards
Enhanced Secure Erase Erases devices that supports this feature
Copy modes
Copy system and les Only the data area of the 2.5”/3.5” SATA Drive is copied and
the empty space isn’t copied
Copy all partitions The partition areas of the HDD are copied and the non-
partition, empty space isn’t copied
Copy the whole HDD The entire HDD is copied, including empty space
Copy a percentage A specied percentage range of the HDD is copied
2. Remove the Drive-Tray Screw, using a Phillips Head Screwdriver.
3. Adjust the position of the Rubber Drive Holder to the appropriate position on the
Drive Tray.
4. Insert the Drive-Tray Screw through the screw hole in the Drive Tray and tighten,
using a Phillips Head Screwdriver. Do not over-tighten.
5. Gently slide the Connector on the M.2 SATA or NVMe Drive(s) at a 30-degree
angle into the corresponding M.2 SATA or NVMe Drive Connector(s) on the Drive
Duplicator and Secure Eraser.
Note: The Connector on the M.2 SATA or NVMe Drive(s) is keyed so that it only ts
one way.
6. Lightly push the M.2 SATA or NVMe Drive(s) down, ensuring the Rubber Drive
Holder connects with the mounting notch on the M.2 SATA or NVMe Drive(s).
Operation
Copy a Drive
Note: The Drive Duplicator and Secure Eraser is capable of 1 to 1 duplication from
M.2 to SATA, SATA to M.2, SATA to SATA, and M.2 to M.2 drives.
1. Navigate to the Setup LCD Display, using the LCD Display Buttons, and press the
Enter Button.
2. Navigate to the Copy Area LCD Display and press the Enter Button.
3. Select a Copy Mode and press the Enter Button.
4. Navigate back to the Main Menu.
5. Select Copy and press the Enter Button.
Warning! Do not disconnect either drive or interrupt the process until the copy process
has completed. Doing so may result in damage to the drive or lost data.
6. When the Green LED Indicator is no longer ashing and has become solid the
copying process is complete.
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. Changes or modications not expressly approved by StarTech.com could void
the user’s authority to operate the equipment.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two
conditions:
(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-
party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only
and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to
which this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks,
registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related
documents are the property of their respective holders.
PHILLIPS® is a registered trademark of Phillips Screw Company in the United States or other countries.
Warranty Information
This product is backed by a two-year warranty.
For further information on product warranty terms and conditions, please refer to www.startech.com/warranty.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)
for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss
of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the
product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the
limitations or exclusions contained in this statement may not apply to you.
Safety Measures
• If product has an exposed circuit board, do not touch the product under power.
FR: startech.com/fr
DE: startech.com/de
ES: startech.com/es
NL: startech.com/nl
IT: startech.com/it
JP: startech.com/jp
StarTech.com Ltd.
45 Artisans Crescent
London, Ontario
N5V 5E9
Canada
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Road
Brackmills,
Northampton
NN4 7BW
United Kingdom
StarTech.com LLP
4490 South Hamilton
Road
GroveConnector, Ohio
43125
U.S.A.
StarTech.com Ltd.
Siriusdreef 17-27
2132 WT Hoofddorp
The Netherlands