Mobile Media Center for Flat-Screen TV One-Touch Height Adjustment STNDMTV70 *actual product may vary from photos FR: Guide de l’utilisateur - fr.startech.com DE: Bedienungsanleitung - de.startech.com ES: Guía del usuario - es.startech.com NL: Gebruiksaanwijzing - nl.startech.com PT: Guia do usuário - pt.startech.com IT: Guida per l’uso - it.startech.com For the latest information, technical specifications, and support for this product, please visit www.StarTech.com/STNDMTV70.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols PHILLIPS® is a registered trademark of Phillips Screw Company in the United States or other countries. This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.
te gebruiken. Warning statements Dit product is alleen bedoeld voor binnengebruik en mag niet buiten worden gebruikt. Make sure that you assemble this product according to the instructions. Draai de schroeven niet te strak vast wanneer u dit product in elkaar zet. Als u weerstand voelt tijdens het vastdraaien van de schroeven, stop dan. Read the entire manual and make sure that you understand the instructions before you start to assemble and use this product.
Durante l’assemblaggio del prodotto, non stringere troppo le viti. Se si incontra resistenza mentre si stringono le viti, interrompere l’operazione. Perigo de energia armazenada! A coluna neste produto contém um mecanismo de elevação que pode mover rapidamente quando remover o equipamento descarregado. Antes de remover equipamento ou fazer ajustes na tensão de elevação, mover o ecrã para a posição mais alta na coluna. O incumprimento destas instruções pode resultar em ferimentos ou danos de propriedade.
Table of Contents Warnings....................................................................................................................................................... i Introduction.............................................................................................1 Product dimensions.................................................................................................................................. 1 Product diagram..........................................................
Adjusting the STNDMTV70....................................................................39 Change the orientation of the TV......................................................................................................... 39 Adjust the angle of the TV...................................................................................................................... 40 Adjust the height of the multimedia shelf........................................................................................
Introduction Product dimensions Support plate rotation: 0° to +90° TV tilt: +5° to -12° 723 mm min 200 mm to max 600 mm 230 mm 285 mm m 0m 15 min 1110 mm to max 1510 mm max 2140 mm 145 mm 440 mm min 200 mm to max 404 mm 290 mm m 430 mm 5m 33 m 0m 70 828 mm Instruction manual 1
Product diagram Camera shelf Connecting plate Support plate Adapter bracket Crossbar Column Multimedia shelf Right leg Plastic cover Pedal lock Left leg Base Caster Instruction manual 2
Technical specifications Unless otherwise indicated, the technical specifications in the table below apply to the TV. Type of measurement Measurement VESA mounting hole pattern on the TV mount 200x200 300x300 400x200 400x400 600x400 40 kg (88 lb.) Weight capacity of TV mount 8 to 25 kg (18 to 55 lb.) Note: If you exceed the lift capacity, you will require additional manual force to raise the TV. Lift capacity of TV mount Weight capacity of multimedia shelf 5 kg (11 lb.
Package contents 1 2 Base Left leg Qty: One Qty: One 4 3 Right leg Left base cover Qty: One Qty: One 5 6 Right base cover Left support bracket Qty: One Qty: One Instruction manual 4
8 7 Right support bracket Column cover Qty: One Qty: One 9 10 Column Multimedia shelf Qty: One Qty: One 12 11 Instruction manual Camera shelf Connecting plate Qty: One Qty: One 5
13 14 Plastic cover Cable clips Qty: One Qty: Three 15 16 Adapter brackets Crossbars Qty: Two Qty: Two 17 Instruction manual 18 End caps Support plate Qty: Four Qty: One 6
19 20 Wrench Hook-and-loop ties Qty: One Qty: Two 22 21 M6x16 mm screws M6x25 mm screws Qty: Four Qty: Two 23 24 Support plate nuts Countersunk screws Qty: Two Qty: Three Instruction manual 7
25 26 M4x6 mm screws M6x8 mm screws Qty: Two Qty: Six 27 28 M6x14 mm screws M8x25 mm screws Qty: Ten Qty: Four 29 Instruction manual 30 Washers Shelf spacers Qty: Four Qty: Four 8
31 32 Hex key Caster wrench Qty: One Qty: One 33 34 M5x14 mm screws M6x14 mm screws Qty: Four Qty: Four 35 36 M6x30 mm screws M8x30 mm screws Qty: Four Qty: Four Instruction manual 9
37 38 M8x50 mm screws TV washers Qty: Four Qty: Four 40 39 Small spacers Large spacers Qty: Eight Qty: Eight 41 Instruction manual Qty: One Requirements • A TV that is compatible with one of the VESA mounting hole patterns STNDMTV70 supports • A Phillips™ type screwdriver Requirements are subject to change. For the latest requirements, please visit www.StarTech.com/STNDMTV70.
Asssembly Warning! Assembling this product requires multiple people. DO NOT attempt to assemble this product and install equipment without assistance. Assemble the base 1. Insert the base into the left leg, aligning the holes in the base with the holes in the left leg. 2. Insert two M6x16 mm screws through the left leg and into the base. 3. Use the hex key to tighten the M6x16 mm screws. 4. Repeat steps 1 to 3 to attach the right leg.
Adjust the height of the casters You can adjust the height of each of the four casters so that the casters are balanced and the assembly doesn’t rock. 1. Use the caster wrench to loosen the nuts above the casters. 2. Rotate the casters counterclockwise or clockwise to raise or lower the casters to the desired height. 3. Use the caster wrench to tighten the nuts.
Attach the column to the base 1. Snap the column cover onto the top of the column. (figure 3) figure 3 Column cover Column 2. Press the pedal locks down on each of the casters to lock them in place and prevent the legs from moving as you attach the column.
3. Line up the holes in the bottom of the column with the holes in the base. 4. While another person holds the column upright, insert the four M8x25 mm screws through the base and into the column. 5. Use the hex key to tighten the M8x25 mm screws.
6. Snap the left base cover and the right base cover onto the base and legs.
Assemble the TV mount 1. Slide the crossbars through the top and bottom openings in the support plate. (figure 7) figure 7 Support plate Crossbar 2. Position the crossbars so that they are centered on the support plate and the holes on the crossbars are aligned with the holes in the support plate. 3. Insert four of the M6x14 mm screws through the crossbars and into the support plate. (figure 8) 4. Use a Phillips type screwdriver to tighten the M6x14 mm screws.
5. Snap an end cap onto each of the four ends of the crossbars. (figure 9) figure 9 Crossbar End cap Attach the support plate to the column 1. Lift up the support plate and hook the top of the support plate onto the protrusion and the studs on the column.
2. Place the support plate nuts over the studs on the column and use your fingers to tighten the support plate nuts. 3. Use the wrench to finish tightening the support plate nuts.
Move the support plate to the lowest position When the spring-loaded pin is positioned in one of the holes in the side of the spool at the bottom of the column, the vertical position of the TV is locked and you can’t move the TV up or down the column. (figure 12) If you pull the pin out of the spool and turn it to the unlocked position (figure 12), the TV is no longer locked in place and can be moved up or down the column. Caution! You should avoid leaving the pin in the unlocked position.
1. To unlock the vertical position of the support plate, at the bottom of the column, next to the spool, pull the pin out and turn it to the unlocked position. (figure 13) figure 13 Column Spool Pin 2. Pull the support plate and adapter brackets down until they are at the bottom of the column. 3. Pull the pin and turn it to the locked position. 4. To make sure that the pin is properly aligned in one of the holes, pull up or push down on the support plate.
Attach the adapter brackets to a flush mounting surface To accommodate different TV designs, the STNDMTV70 comes with five sets of screws of different lengths and diameters, TV washers with two hole sizes, and two sizes of spacers. Warning! Make sure that the weight of the TV doesn’t exceed the weight capacity of this product. If you exceed the weight capacity, you might experience personal injury or damage to the product. This product can support the following weight: 40 kg (88 lb.
figure 14 M5x14 mm screw M6x14 mm screw TV washer Adapter bracket Top of TV Instruction manual 22
Attach the adapter brackets to a recessed mounting surface To accommodate different TV designs, the STNDMTV70 comes with five sets of screws of different lengths and diameters, TV washers with two hole sizes, and two sizes of spacers. Warning! Make sure that the weight of the TV doesn’t exceed the weight capacity of this product. If you exceed the weight capacity, you might experience personal injury or damage to the product. This product can support the following weight: 40 kg (88 lb.
M8x50 mm combined with or or 2 large spacers 1 small spacer 2 small spacers 2 large spacers 2 large spacers combinations available, and select the one that works best with the TV. 3. Position the adapter brackets so that the hooks on the adapter brackets are pointed towards the bottom of the TV and are aligned with the mounting holes on the back of the TV. 4.
figure 15 M6x30 mm screw M8x30 mm screw M8x50 mm screw TV washer Spacers Adapter bracket Top of TV Instruction manual 25
the TV. Attach the TV to the column Warning! Attaching the TV requires multiple people. Do not attempt to complete this task by yourself. Warning! Make sure that you move the support plate to the lowest position on the column before you attach the TV. For more information, see the “Move the support plate to the lowest position” section. 1. If you haven’t done so already, press the pedal locks down on each of the casters to prevent the legs from moving as you attach the TV to the column. 2.
adapter brackets over the crossbars. (figure 16) 3. Center the TV on the crossbars, and insert four M6x14 mm screws through the crossbars and into the adapter brackets.
4. Use a Phillips type screwdriver to tighten the M6x14 mm screws. 5. To secure the TV in the landscape position, insert two of the M6x8 mm screws into the support plate and use a Phillips type screwdriver to tighten the screws.
section. Counterbalance the weight of the TV When you add a TV to the STNDMTV70, you need to adjust the lift capacity of the TV cart to support the weight of the TV. If the lift capacity of the STNDMTV70 isn’t set correctly, when you let go of the TV, it could free fall down the column or move up the column unaided, resulting in damage to the TV or personal injury. Warning! Counterbalancing the weight of the TV requires multiple people. Do not attempt to complete this task by yourself. 1.
Note: To counterbalance the weight of the TV, you may need to turn the knob near the spool up to 80 full revolutions. 3. Repeat step 2 until the weight of the TV is counterbalanced. Note: When the weight of the TV is properly counterbalanced, the TV will remain stationary on the column when you loosen your hold on it, and you will be able to move the TV up or down the column with minimal effort. 4. When the weight of the TV is counterbalanced, move the TV to the desired height. 5.
1. Carefully separate the two halves of the plastic cover. (figure 20) 2. Place the two halves of the plastic cover around the spool and snap the two sides together. 3.
tabs on the top of the plastic cover into the slots on the column. 4. Press the plastic cover down towards the base and snap the tabs on the plastic cover into the holes on the column and the base. (figure 21) Attach the cable clips 1. Remove the backing from the cable clips.
2. Attach the cable clips along the column. 3. Route the cables down the column and through the cable clips. 4. Snap the cable clips closed. (figure 22) Install the multimedia shelf 1. Place the shelf spacers over the projections on the underside of the multimedia shelf. 2. Position the right and left support brackets over the washers so that the holes are aligned and the scalloped edges of the adapter brackets are pointed towards the outside edges of the multimedia shelf. 3.
screws through the washers, adapter brackets, and into the projections on the multimedia shelf. 4. Use a Phillips type screwdriver to tighten the M6x8 mm screws.
5. Turn the knob on the shelf bracket counterclockwise to loosen it. 6. Move the shelf bracket to the height that you want the multimedia shelf to be at, and turn the knob clockwise to tighten it. (figure 24) 7.
multimedia shelf downwards. 8. Insert two M6x14 mm screws into the multimedia shelf and into the shelf bracket. 9. Use a Phillips type screwdriver to tighten all four of the M6x14 mm screws. (figure 25) Attach the camera shelf figure 26 Countersunk screw Camera shelf Connecting plate 1. Line up the holes on the camera shelf with the holes on the end of the connecting plate. 2.
the connecting plate. 3. Use a Phillips type screwdriver to tighten the countersunk screws. (figure 26) 4. Insert the two M4x6 mm screws into the camera shelf and into the side of the connecting plate. (figure 27) 5. Use a Phillips type screwdriver to tighten the screws in place.
6. Determine the height that you want the camera shelf to be at and line it up with the mounting slots on the back of the column. 7. Insert the two M6x25 mm screws through the connecting plate and into the column. (figure 28) 8. Use a Phillips type screwdriver to tighten the screws in place. Attach the wrench figure 29 1. Thread the two hook-and-loop ties through the hole in one of the support brackets under the multimedia shelf. 2.
Adjusting the STNDMTV70 Change the orientation of the TV You can position the TV in either landscape or portrait orientation on the STNDMTV70. 1. To display the TV in portrait orientation, if present, remove the two M6x8 mm screws from the back of the support plate. 2. Rotate the TV 90° clockwise. 3. Reinsert the M6x8 mm screws you removed in step 1, and use a Phillips type screwdriver to tighten them.
Adjust the angle of the TV 1. Turn the knobs on either side of the support plate counterclockwise to loosen them. 2. Push or pull the top or bottom of the TV to adjust the angle of the TV. 3. Turn the knobs on either side of the support plate clockwise to tighten them.
Adjust the height of the multimedia shelf 1. Under the multimedia shelf, turn the knob counterclockwise. 2. Move the multimedia shelf to the desired height, and turn the knob clockwise to tighten it into place.
Adjust the height of the camera shelf 1. Loosen the two M6x25 mm screws attaching the connecting plate to the column. 2. Move the connecting plate to the desired height, and use a Phillips type screwdriver to tighten the M6x25 mm screws into place.
Lock the vertical position of the TV When the TV is at the height that you want it to be at, you should lock the vertical position of the TV to prevent the TV from moving up or down the column. Warning! Exercise caution when you pull the pin out of the spool and turn it to the unlocked position. The weight of the TV may not be counterbalanced and the TV could free fall down the column or spring upwards, resulting in damage to the TV or personal injury. 1.
Technical support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. For the latest drivers/software, please visit www.startech.com/downloads Warranty information This product is backed by a five-year warranty. StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
