Lockable Floor Stand for iPad STNDTBLT1FS *actual product may vary from photos FR: Guide de l’utilisateur - fr.startech.com DE: Bedienungsanleitung - de.startech.com ES: Guía del usuario - es.startech.com NL: Gebruiksaanwijzing - nl.startech.com PT: Guia do usuário - pt.startech.com IT: Guida per l’uso - it.startech.com For the latest information, technical specifications, and support for this product, please visit www.startech.com/STNDTBLT1FS.
Table of Contents Introduction.............................................................................................1 Product diagram......................................................................................................................................... 1 Tablet holder dimensions....................................................................................................................... 1 Tablet stand dimensions...............................................................
Introduction The STNDTBLT1FS is a rugged and durable fixed-height tablet stand that you can use as a stand-alone kiosk or as an informational display. The tablet stand features a lockable tablet holder for increased security, and a base that you can screw into the floor to create a stationary holder. The tablet stand is designed to display tablets in either a portrait or landscape position. The STNDTBLT1FS can support up to two pounds of weight.
Tablet stand dimensions Tablet base dimensions Instruction manual 2
Package contents 1 2 3 Tablet holder Keys Base Qty: One Qty: Two Qty: One 4 5 6 Base connector Connecting block Pole Qty: One Qty: One Qty: One 7 8 9 x4 x4 Rubber feet M6 screws Qty: Four Qty: Eight 10 11 M4 screws Qty: Four 12 Allen key Anchor screws Anchors Qty: One Qty: Four Qty: Four 13 14 15 Foam pads Foam blocks Instruction manual Qty: Six Qty: Six Qty: One Instruction manual 3
Installation requirements • The STNDTBLT1FS is designed for 9.7 in. iPad, iPad Air, and iPad Pro tablets. • A USB charging cable at least 6 feet in length. • A Phillips screwdriver. • A drill with a 1/4 in. drill bit (if you attach the tablet stand to the floor). • A hammer (if you attach the tablet stand to the floor). For the latest requirements, please visit www.startech.com/STNDTBLT1FS.
2. Run the USB cable that you intend to use to supply power to the tablet through the pole (6) (figure 2). figure 2 Pole Bottom end of pole USB cable 3. Insert the four countersunk M6 screws (8) through the holes on the bottom of the base, into the base connector (4), and into the pole (figure 3). 4. To tighten the screws, use the Allen key (10) to turn the screws clockwise.
Attach the tablet holder to the pole 1. Place the connecting block (5) on top of the pole (6) so that the four holes on the connecting block line up with the four holes in the pole. 2. Insert the remaining four M6 screws (8) through the connecting block and into the pole (figure 4). 3. To tighten the screws, use a Phillips screwdriver to turn the screws clockwise. figure 4 Screwdriver M6 screws Connecting block Pole 4.
figure 5 Tablet holder Connecting block Pole USB cable (sold separately) 5. Place the tablet holder (1) on top of the connecting block so that the four holes on the tablet holder line up with the four holes on the collecting block. Note: You can attach the tablet holder in a portrait or a landscape position. 6. Insert the four M4 screws (9) through the tablet holder and into the connecting block (figure 6). 7. To tighten the screws, use a screwdriver to turn the screws clockwise.
Assemble the tablet holder The tablet holder is designed for iPad, iPad Air, and iPad Pro tablets, however, you can use the foam pads and blocks in order to fit other types of tablets. The opening in the tablet holder measures 198 mm by 149 mm. iPad If you intend to use an iPad in the tablet holder, place the foam pads and blocks in the formation described below. 1. Use one of the keys (2) to unlock the tablet holder (1) (figure 7). figure 7 Tablet holder Key 2.
3. Remove the backing from three of the foam pads (13). 4. On the left side of the tablet holder, stick two of the foam pads to the inside of the metal tabs. 5. On the right side of the tablet holder, stick one of the foam pads to the inside of the metal tab (figure 9). figure 9 Stick the foam pads to the inside of the metal tabs. Foam pads Tablet holder 6. Remove the backing from three of the foam blocks (14). 7.
When you’re done affixing the pads and blocks, the tablet holder should look like this: iPad Air and iPad Pro If you intend on using an iPad Air or an iPad Pro in the tablet holder, place the foam blocks in the formation described below. 1. Use one of the keys (2) to unlock the tablet holder (1) (figure 11). figure 11 Tablet holder Key 2. Open the front panel of the tablet holder (figure 12).
figure 12 Tablet holder 3. Remove the backing from the six foam blocks (14). 4. On the left side of the tablet holder, stick two of the foam blocks to the inside of the metal tabs. 5. On the right side of the tablet holder, stick one of the foam blocks to the inside of the metal tab. 6. On the top of the tablet holder, stick one of the foam blocks to the inside of the metal tab. 7. On the bottom of the tablet holder, stick two of the foam blocks to the inside of the metal tabs (figure 13).
When you’re done affixing the pads and blocks, the tablet holder should look like this: Place the tablet in the tablet holder To avoid scratching the surface of the tablet, handle the tablet carefully when you insert it into the tablet holder. The weight capacity of the STNDTBLT1FS is up to two pounds. 1. If the tablet holder (1) is locked, use one of the keys (2) to unlock the tablet holder and open the front panel. 2. Carefully place the tablet into the tablet holder (figure 14).
3. Attach the USB cable to the charging port on the tablet. 4. Close the front panel of the tablet holder. 5. To lock the tablet holder, press the lock button on the side of the tablet holder (figure 15). figure 15 Tablet holder Lock button Pole Attach the tablet stand to the floor You can secure the STNDTBLT1FS to the floor or leave it as a free-standing tablet stand. To attach the tablet stand to the floor, complete the following: 1. Place the tablet stand where you want it to go. 2.
3. Use a drill to drill 1/4 inch holes in the areas that you marked with the pencil. 4. Hammer the four anchors (12) into the holes that you drilled. 5. Place the tablet stand so that the four holes on the base are on top of the anchors. 6. Insert the four anchor screws (11) through the holes in the base and into the anchors (figure 17). 7. Turn the screws clockwise to tighten them.
Technical support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. For the latest drivers/software, please visit www.startech.com/downloads Warranty information This product is backed by a two-year warranty. StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
