Dual DVI USB KVM Switch SV231DD2DUA SV431DD2DUA DE: Bedienungsanleitung - de.startech.com FR: Guide de l'utilisateur - fr.startech.com ES: Guía del usuario - es.startech.com IT: Guida per l'uso - it.startech.com NL: Gebruiksaanwijzing - nl.startech.com PT: Guia do usuário - pt.startech.com For the most up-to-date information, please visit: www.startech.
FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Table of Contents Introduction .......................................................................................................................................................1 Packaging Contents.................................................................................................................................1 System Requirements.............................................................................................................................1 Installation.....................
Introduction Packaging Contents • 1 x SV231DD2DUA or SV431DD2DUA KVM switch • 1 x Power Adapter • 1 x Instruction Manual System Requirements • DVI enabled computer system/video card • USB enabled computer system • DVI enabled display devices (e.g. monitor, projector, TV, etc.) • A standard 104-key wired USB keyboard • A standard 3-button wired USB mouse Installation NOTE: Prior to the installation, please power off all devices that will be connected to this system.
Front View (SV431DD2DUA shown) Port Selection/Link LED Power LED Port Selection button Rear View (SV431DD2DUA shown) Console DVI connector (output) PCI connectors FUNC button DC Power connector 3.
* installation pictures are representation only 1. Plug 1 or 2 monitor(s) into the Console side DVI connector(s); plug a USB keyboard and a USB mouse into the dedicated USB keyboard and mouse ports on the KVM switch. 2. Use a male-to-male DVI video cable to connect the DVI connector(s) on the computer’s video card, to one of the KVM’s PC ports (ie. PC1). A dedicated DVI, USB and audio 4-in-1 KVM cable can be used (ie. StarTech.com ID: USBDVI4N1A6). 3.
Driver Installation No driver installation is required for the KVM switch, as the keyboard and mouse uses native USB keyboard/mouse drivers that are already installed on all operating systems that fully support USB. Operation Front Panel Port Selection/Link LED The LED turns green when the connected computer is powered-on. The corresponding LED will also illuminate red when that PC port is currently selected.
Rear Panel (SV431DD2DUA only) To adjust the video signal strength/equalization settings for the length or quality of DVI cable being used, the “FUNC” button combined with the front panel push buttons can be used. 1. Press “FUNC” button three times, and the LED for “POWER” will start to flash once per second. 2. Press front panel push button “1” one or two times to adjust the signal equalization with one beep (normal) or two beeps (enhance) respectively.
HotKey Control A Hotkey command is a short keyboard sequence for selecting a computer, activating computer scan, etc. A hotkey sequence starts with two left keystrokes (successively within 0.2 seconds) followed by one or two more keystrokes. A high-pitch beep will be generated for each correct hotkey command; otherwise, one low-pitch beep is generated for errors and the bad key sequence will not be forwarded to the selected computer.
Scan Time Four options are available for users to set the Scan Time duration, it Includes 3, 8, 15 and 30 seconds. Note: Scan Time is set to 3 seconds by default. To adjust Scan Rate, set the scan time of duration before switching to the next computer: Left + Left + The KVM Switch generates 1 to 4 beeps indicating a scan time duration for 3, 8, 15 or 30 seconds respectively. Audio Stick There are two options for Audio Stick: ON and OFF.
Alternative Hotkey Commands In addition to the Left + Left hotkeys, there are two alternative hotkey sequences available. 1. For the following operations, users may press twice instead of pressing left twice. To select a computer: + + <1> (Example: Select the computer at port 1.) + + <2> (Example: Select the computer at port 2.) NOTE: Do not use the keypad at the right of the keyboard. 2.
Specifications SV231DD2DUA SV431DD2DUA 2 4 Number of Ports Computer Connectors (per port) 2 x DVI-I female 1 x USB type B 2 x 3.5mm mini-jack Console Connectors 2 x DVI-I female 4 x USB type A 2 x 3.5mm mini-jack Maximum Video Resolution 1920x1200 @ 60Hz DDC2B Yes Audio Yes OSD No Cascadable No Switching Modes Front Panel Buttons, HotKeys Power Adapter 9-12VDC, 1.5A (included) Enclosure Material Metal Dimensions 100.0mm x 160.0mm x 57.0mm 130.0mm x 220.0mm x 60.
Technical Support StarTech.com’s lifetime technical support is an integral part of our commit-ment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/ support and access our comprehensive selection of online tools, documentation, and downloads. Warranty Information This product is backed by a three year warranty. In addition, StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
