2/4 Port DVI VGA Dual Monitor USB KVM Switch with Audio & USB 2.0 Hub SV231DDVDUA SV431DDVDUA *SV431DDVDUA Shown DE: Bedienungsanleitung - de.startech.com FR: Guide de l'utilisateur - fr.startech.com ES: Guía del usuario - es.startech.com IT: Guida per l'uso - it.startech.com NL: Gebruiksaanwijzing - nl.startech.com PT: Guia do usuário - pt.startech.com For the most up-to-date information, please visit: www.startech.
FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Table of Contents Introduction.............................................................................................1 Packaging Contents.................................................................................................................................. 1 System Requirements............................................................................................................................... 1 Installation..........................................................................
Front View (SV431DDVDUA shown) Port Selection Button Port Selection/ Link LED Power Button Rear View (SV431DDVDUA shown) Console DVI/VGA connector (output) PC1 connectors Function Button DC Power connector 3.
Introduction The SV231DDVDUA 2-port or SV431DDVDUA 4-port Dual Monitor KVM Switch (DVI+VGA) offers a complete multimedia switching solution, letting users control two Dual Display computers using a single USB mouse and keyboard peripheral set. With support for high-resolution video interfaces, this dual view KVM switch provides one VGA (analog) and one DVI-I port per computer connection, as well as audio switching capability between connected computers.
Installation NOTE: Prior to the installation, please power off all devices that will be connected to this system. Ensure that all devices you will connect are properly grounded. Place cables away from fluorescent lights, air conditioners, and machines that are likely to generate electrical noise. If you experience any problems using a USB KVM switch, the following BIOS setup changes may be necessary for PC users and not necessary for Mac users: Set HALT ON ERROR to ALL BUT KEYBOARD.
OPTIONAL: Connect any other USB peripherals you wish to share between the connected computers/devices to the extra USB Hub ports on the Console side. 5. Connect the external power adapter from a wall outlet to the power connector on the rear panel of the KVM switch. The Power LED should light up solid and/or the LED for the selected PC port. 6. Power up the first computer/device and wait for it to fully boot and test keyboard/ mouse functionality. 7.
Operation Front Panel Port Selection/Link LED The LED turns green when the connected computer is powered-on. The corresponding LED will also illuminate red when that PC port is currently selected. Port Selection Button 2 Port: Pressing the front panel “Select” button toggles between the PC ports on the KVM switch. 4 Port: Each push button on the front panel corresponds with a PC port. Pressing the button will immediately select that port.
Rear Panel (SV431DDVDUA only) To adjust the video signal strength/equalization settings for the length or quality of DVI cable being used, the “FUNC” button combined with the front panel push buttons can be used. 1. Press “FUNC” button three times, and the LED for “POWER” will start to flash once per second. 2. Press front panel push button “1” one or two times to adjust the signal equalization with one beep (normal) or two beeps (enhance) respectively.
HotKey Control A Hotkey command is a short keyboard sequence for selecting a computer, activating computer scan, etc. A hotkey sequence starts with two left keystrokes (successively within 0.2 seconds) followed by one or two more keystrokes. A highpitch beep will be generated for each correct hotkey command; otherwise, one lowpitch beep is generated for errors and the bad key sequence will not be forwarded to the selected computer.
Scan Time Four options are available for users to set the Scan Time duration, it Includes 3, 8, 15 and 30 seconds. Note: Scan Time is set to 3 seconds by default. To adjust Scan Rate, set the scan time of duration before switching to the next computer: Left + Left + The KVM Switch generates 1 to 4 beeps indicating a scan time duration for 3, 8, 15 or 30 seconds respectively. Audio Lock There are two options for Audio Lock: ON and OFF. When ON, audio selection follows computer selection.
Alternative Hotkey Commands In addition to the Left + Left hotkeys, there are two alternative hotkey sequences available. 1. For the following operations, users may press twice instead of pressing left twice. To select a computer: + + <1> (Example: Select the computer at port 1.) + + <2> (Example: Select the computer at port 2.) NOTE: Do not use the keypad at the right of the keyboard. 2.
Change Leading Hotkey The default leading hotkey sequence involves pressing the left twice in succession (e.g. left + left ). This can be changed to the right key instead, to avoid accidental activation due to using the left key for functions such as Copy/Paste.
Specifications Number of Ports SV231DDVDUA SV431DDVDUA 2 4 1 x DVI-I female 1 x DE-15 VGA female Computer Connectors (per port) 1 x USB type B 2 x 3.5mm mini-jack 1 x DVI-I female 1 x DE-15 VGA female Console Connectors 4 x USB type A 2 x 3.5mm mini-jack Digital: 1920x1200@60Hz Maximum Video Resolution Analog: 1920x1440@60Hz DDC2B Yes Audio Yes OSD No Cascadable No Switching Modes Front Panel Buttons, Hotkeys Power Adapter 9~12VDC, 1.
Technical Support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. For the latest drivers/software, please visit www.startech.com/downloads Warranty Information This product is backed by a three year warranty. In addition, StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
