4-Port KVM Switch for DisplayPort Computers - USB 3.0 SV431DPU3A2 *actual product may vary from photos FR: Guide de l’utilisateur - fr.startech.com DE: Bedienungsanleitung - de.startech.com ES: Guía del usuario - es.startech.com NL: Gebruiksaanwijzing - nl.startech.com PT: Guia do usuário - pt.startech.com IT: Guida per l’uso - it.startech.com For the latest information, technical specifications, and support for this product, please visit www.StarTech.com/SV431DPU3A2.
FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Table of Contents Introduction.............................................................................................1 Product diagram......................................................................................................................................... 1 Package contents....................................................................................................................................... 2 System requirements...........................................................
Technical support....................................................................................9 Warranty information.............................................................................
Introduction You can use the SV431DPU3A2 to control four DisplayPort computers with a single monitor, keyboard, mouse, and audio peripheral set. The KVM switch features a built-in two-port USB hub that’s separate from your keyboard and mouse, enabling you to share USB peripheral devices between each connected computer. The KVM switch also supports USB 3.0 technology, so you can achieve data transfer rates up to 5Gbps.
Package contents • 1 x 4-port DisplayPort KVM switch • 4 x rubber feet • 1 x universal power adapter (NA/EU/UK/AU) • 1 x quick-start guide System requirements • Host computer with a USB 2.0 or USB 3.0 port • Computer equipped with DisplayPort • Display device (for example, monitor, TV, and so on) equipped with DisplayPort • USB keyboard and mouse support The maximum resolution for this KVM switch is 4K at 30 Hz.
KVM switch setup Attach the rubber feet To affix the rubber feet to the bottom of the KVM switch, peel off the backing on each of the four rubber feet and stick them to the bottom of the KVM switch in the indicated areas. Connect a console to the KVM switch 1. Turn off your computer and any devices or peripherals that are connected to it (for example, printers, external hard drives, and so on). 2. Connect a monitor to the Console DisplayPort port on the KVM switch. 3.
7. To turn on the KVM switch, press the Power button. The LED indicator should illuminate to indicate that the KVM switch is receiving power. 8. Change the focus of the KVM switch to the computer or device that you connected to the KVM switch and turn on the computer or device. Wait for it to fully load and then test the keyboard and mouse functionality of the connected computer or device. 9. Repeat step 8 for all of the connected computers or devices.
Operating the KVM switch About the LED indicators The KVM switch features five LED indicators: One LED indicator for each of the four port connections and one power LED. LED Port selection/link LEDs Power LED Behavior Significance The green LED is illuminated. The port is active and the connected computer or device is turned on. The red LED is illuminated. The computer or device connected to the port is currently selected. The LED is blinking. The KVM switch is completing an auto scan.
Change the AutoScan interval time You can set the AutoScan interval time to one of four options: 3, 8, 15, or 30 seconds. By default, the AutoScan interval time is set to 3 seconds after a blackout or restart.
Using hotkey commands You can use hotkey commands to operate the KVM switch. All hotkey commands begin by pressing the left Ctrl key twice and then pressing one or two additional keys. The KVM switch emits a high-pitched beep when you enter a correct command and a low-pitched beep when you enter an incorrect command. Incorrect hotkey commands aren’t forwarded to the computer. Enable hotkey commands 1.
Number of beeps Corresponding AutoScan interval 1 3 seconds 2 8 seconds 3 15 seconds 4 30 seconds To change the AutoScan interval time, press left Ctrl, left Ctrl, F3 until you hear the number of beeps that corresponds to the duration of time that you want to set. Start a manual scan You can use the manual scan feature to manually switch between computers that are turned on and connected to the KVM switch. 1. To start a manual scan, press left Ctrl, left Ctrl, F2. 2.
Technical support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. For the latest drivers/software, please visit www.startech.com/downloads Warranty information This product is backed by a two-year warranty. StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
