USB Dual VGA Cat5 KVM Console Extender - 650ft/200m SV565DUTPU *actual product may vary from photos DE: Bedienungsanleitung - de.startech.com FR: Guide de l'utilisateur - fr.startech.com ES: Guía del usuario - es.startech.com IT: Guida per l'uso - it.startech.com NL: Gebruiksaanwijzing - nl.startech.com PT: Guia do usuário - pt.startech.com For the most up-to-date information, please visit: www.startech.
FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Table of Contents Introduction.............................................................................................1 Features......................................................................................................................................................... 1 System Requirements............................................................................................................................... 1 Packaging Contents........................................................
Introduction The SV565DUTPU USB Dual VGA KVM Console Extender over CAT5 UTP lets you Operate a Dual VGA PC or KVM switch up to 650ft (200 m) away, as if it was installed locally, at high-definition 1920x1200 resolution. PC connection cables are included with this product for a ready to use solution.
NOTE: The total length of cable between the Local and Remote Units cannot exceed 650 feet (200 meters), including patch cables (if used). It is suggested using Cat5 cables with identical brand and length when connected simultaneously. Category 5e and 6 cabling is compatible with this product and may improve performance. NOTE: Long cable lengths between the Local and Remote Units may adversely affect image quality at high resolutions and refresh rates.
Connecting Your KVM Extender Preparing Your Site Before you can install the product, you need to prepare your site. 1. Determine where the local computer will be located and set up the computer. 2. Determine where the console devices (mouse, keyboard, monitor) will be located and place them appropriately. 3.
Installation Installing the Local Unit 1. Place the Local Unit near the computer. 2. Switch off the computer and disconnect any connected devices. 3. Using the provided StarTech.com integrated KVM cable, connect the end of the cable that has the USB or PS/2 + VGA connectors to the VGA Out connectors and the USB or mouse and keyboard PS/2 connectors on the computer as appropriate. (The PS/2 version of the cable is color-coded.
7. Connect a USB mouse, keyboard, and a VGA monitor to the indicators marked as CONSOLE on the Remote Unit. 8. Connect the UTP cable connections for Remote Unit to the NETWORK RJ-45 connector on the Remote Unit. Connect the opposite end to a terminated wall outlet (if using premises cabling). CAUTION: The UTP network cables that connect the Local and Remote Units carry electrical current and should not be plugged in to other devices, as they may cause damage.
Push-Button Control and LEDs A push-button on the respective top panel of Local Unit and Remote Unit can be used to select the control mode. Push-Button on Remote Unit The button on the top panel of Remote Unit can be used to switch mode between Local and Remote in the sequence as the diagram shown below: Local On Remote On Local On: When the LED “Local” lights up, the system controls its local computer. Remote On: When the LED “Remote” lights up, the system remotely controls the Local Unit.
Video Compensation Video Compensation allows the user to adjust the equalization from the Remote Unit console to optimize video performance based on the length of cable being used, as well as other factors that may affect the display, with adjustments available for Equalizer (Sharpness), Gain (Brightness) and Skew (RGB).
Hotkey Commands A hotkey command is a short key sequence to select a computer, activate computer scan, and so forth. The KVM Extender interprets keystrokes for hotkeys all the time. And the built-in buzzer generates a high-pitched beep for correct hotkey command; otherwise, one short and one long beep are generated for a bad command, in which the bad key command won’t be sent to the extender unit or the selected computer.
NOTE: The hotkey command will be automatically time-out if • There is no activity detected by the keyboard within 3 seconds after the leading code input (when Mask Hotkey OFF) or within 6 seconds after [BTN] (2sec.) (when Mask Hotkey ON). • Press the button Esc once to escape from the hotkey mode. • Press the Push-Button once to escape from the hotkey mode and switch to either the Local or Remote mode.
Hotkey Commands for both Remote Unit and Local Unit Before inserting the hotkey commands, it’s required to launch the leading code ( [Ctrl] + [Ctrl] or [Ctrl] + [Ctrl] + [E] ) depending on Cascade Architecture. Hotkey Commands Keyboard Function Descriptions Push Button Cascading status selection * [both Units] One beep: Enable Standard Mode * [Remote Unit] [Alt] + [E] N/A Two beeps: Enable Compatibility Mode, and the user at Remote Unit accessing to the KVM switch that is connecting to Local Unit.
Hotkey Commands Keyboard Function Descriptions Push Button [2] Remote mode selection Enable the user at the Remote Unit exclusive accessing to computer (KVM Switch) that connects to the Local Unit. (only if the Local Unit is in Remote or Auto mode). Disable Local Unit user accessing to the Local Unit during this mode.
Hotkey Commands for Local Unit Hotkey Commands Keyboard Push-Button [3] N/A Function Descriptions Auto Mode Selection Latch Time Selection [F3] [F6] Auto Mode latch time setting: The extender generates 1 to 4 beeps to indicate the duration of latch time: 5, 15, 30, 60 seconds respectively.
Hotkey Commands for Remote Unit The Video Adjustment function is on Remote Unit only. To launch its hotkey command, also start with the specific leading code depending on situation, and then press F11 to enter Video Adjustment Mode. After adjustment, just press Esc to escape from this Mode. Hotkey Commands Keyboard Push-Button Function Descriptions Video Adjustment Equalizer / Gain Adjustment Equalizer (Sharpness): (Num Lock LED + Caps Lock LED) Flashing 1. For both 1st and 2nd monitors 1.
Hotkey Commands Keyboard Push-Button Function Descriptions Blue/Green/Red Color Adjustment Caps Lock LED Flashing [B](Blue) [G](Green) [R](Red) * Choose one color at a time for adjustment 1. For both 1st and 2nd monitors 1.1 Press or to coarse tune; 8 levels for adjustment 1.2 Press and Hold Shift + or to fine tune 2. For 1st monitor 2.1 Press F1 or F2 to coarse tune; 8 levels for adjustment 2.2 Press and Hold Shift + F1 or F2 to fine tune 3. For 2nd Monitor 3.
Specifications Maximum Resolution 1920 x 1200 at maximum UTP cable length Maximum Range 650 feet (200 meters) Network Cabling Type Straight-through Unshielded Twisted Pair (UTP) Cat 5 Connectors Each, Local and Remote Unit 4 x HD-15 female (2 x KVM, 2 x console VGA) 2 x RJ-45 2 x USB keyboard/mouse (for console) 1 x Power (optional) Power Adapter 9V DC, 600mA, center positive (per unit) (Optional; only required when connected using a conventional KVM switch) Instruction Manual 15
RJ-45 Connector Pinout Instruction Manual Pin Wire Color Pair Function 1 White/ Orange 2 T 2 Orange 2 R 3 White/ Green 3 T 4 Blue 1 R 5 White/ Blue 1 T 6 Green 3 R 7 White/ Brown 4 T 8 Brown 4 R 16
Troubleshooting If you encounter problems with the KVM Extender during the installation or operations, please check through this section for a possible solution. If your problem is not listed here and you can not resolve the issue, please contact your local dealer for the fastest assistances. Symptom Solution •Verify that all the cables are qualified according to the hardware requirement section. •Verify that all the cables are properly connected to their ports and are firmly seated.
Symptom Keyboard hotkeys are inoperable when the KVM Extender connects with the KVM Switch Solution •Apply compatibility mode hotkey commands. •Verify if the Extender has enough power. Computer units are inoperable •Verify if the units have enough power. If the power is insufficient for the needs, purchase a power adapter from your local dealers.
Technical Support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. For the latest drivers/software, please visit www.startech.com/downloads Warranty Information This product is backed by a three year warranty. In addition, StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.