Sit-Stand Workstation Wall Mount - Single Monitor WALLSTS1 *actual product may vary from photos FR: Guide de l’utilisateur - fr.startech.com DE: Bedienungsanleitung - de.startech.com ES: Guía del usuario - es.startech.com NL: Gebruiksaanwijzing - nl.startech.com PT: Guia do usuário - pt.startech.com IT: Guida per l’uso - it.startech.com JP: 取扱説明書 - jp.startech.com For the most up-to-date information, please visit: www.startech.
Warning statements Dichiarazioni di avvertenza Make sure that you assemble this product according to the instructions. Assicurarsi di Assemblare il prodotto secondo le istruzioni. Read the entire manual and make sure that you understand the instructions before you start to assemble and use this product. Leggere l’intero manuale e assicurarsi di aver compreso tutte le istruzioni prima di iniziare ad assemblare e a utilizzare questo prodotto. Never operate this product if parts are missing or damaged.
Advertencias de uso Asegúrese de ensamblar este producto según las instrucciones. Lea todo el manual y asegúrese de haber comprendido bien las instrucciones antes de proceder con el ensamblaje y el uso de este producto. Nunca opere o ponga en funcionamiento este producto si faltan piezas o hay daños en las mismas. El uso de este producto es solo para interiores y no debe utilizarse en exteriores. Cuando ensamble este producto, no apriete los tornillos más de lo debido.
Table of Contents Warnings....................................................................................................................................................... i Product dimensions................................................................................1 Product diagram.....................................................................................3 Technical specifications.........................................................................4 Package contents..............
Clean the keyboard tray.........................................................................33 Technical support....................................................................................34 Warranty information.............................................................................
Product dimensions 175 mm (6.9 in.) 333 mm (13.1 in.) 672 mm (26.4 in.) 395 mm (15.5 in.) 1073 mm (42.2 in.) 16 mm (0.6 in.) 79 mm (3.1 in.) 1 160 mm (6.3 in.) 124 mm (4.9 in.) 210 mm (8.3 in.) Instruction manual 7 mm (0.3 in.) 104 mm (4.1 in.) 13 mm (0.5 in.) 50 mm (2 in.
8 mm to 217 mm 449 mm (17.7 in.) (0.3 in. to 8.5 in.) (0.3 in. to 8.5 in.) 668 mm (26.3 in.) Instruction manual 8 mm to 217 mm 2 255 mm (2.2 in.) 207 mm (8.1 in.) 213 mm (8.4 in.) 926 mm (36.5 in.) 436 mm (17.2 in.) 956 mm (37.6 in.) 369 mm to 548 mm (14.5 in. to 21.6 in.) 124 mm (4.9 in.) 50.5 mm (1.9 in.
100 mm (3.9 in.) 4.5 mm (0.2 in.) 75 mm (2.9 in.) 75 mm (2.9 in.) 100 mm (3.9 in.) 64 mm (2.5 in.) 44 mm (1.7 in.
Technical specifications Type of measurement Measurement 75 x 75 mm 100 x 100 mm VESA -5° to +35° Tilt (monitor) 0° to +90° Tilt (keyboard) 360° Pivot (monitor) +/-90° Swivel (monitor arm) Instruction manual 4
Type of measurement Measurement 24 in. or less Supported monitor size LB kg 4 to 17.6 lb. (2 to 8 kg) Supported weight (monitor) LB kg 5.5 lb. (2.
Package contents 1 2 Monitor arm Keyboard tray Qty: One Qty: One 3 4 Column Vesa monitor mount Qty: One Qty: One 5 Instruction manual 6 Wall Plate Adhesive strip Qty: One Qty: One 6
7 8 Socket driver 6 mm hex key Qty: One Qty: Four 9 10 M6x10 mm screws M8x20 mm screw Qty: Three Qty: One 11 Instruction manual 12 Metal washer Plastic washer Qty: One Qty: One 7
14 Mounting screws Concrete anchors Qty: Four Qty: Four 15 16 5 mm hex key M6x12 mm screws Qty: One Qty: Four 17 18 2.
19 20 M6x8 mm screw Instruction manual Qty: One Qty: One Requirements • Monitor that is compatible with one of the VESA mounting hole patterns that WALLSTS1 supports • Pencil or pen to mark the wall • Phillips type screwdriver • ¹/₄ inch drive ratchet Requirements are subject to change. For the latest requirements, please visit www.StarTech.com/WALLSTS1.
Assembly Attach the wall plate to the wall Warning! Wall structures vary, and it is important to make sure that the type of structure and mounting hardware that you are using will properly support the mounted equipment. Failure to do so may result in personal injury and/or equipment damage. The wall should be capable of supporting at least four times the weight of the mounted equipment. Warning! The mounting hardware included with this product might not be adequate for some wall structures.
3. Position the wall plate where you want to hang the WALLSTS1 and make sure that the plate is vertical. 4. Use the four mounting holes in the wall plate as a template and mark the wall. 5. Follow the appropriate steps for the type of wall that you’re attaching the WALLSTS1 to and attach the wall plate to the wall.
Attach the monitor arm to the wall plate 1. Place the monitor arm onto the projection on the wall plate.
2. Place the plastic washer into the joint in the monitor arm. 3. Place the metal washer onto the plastic washer. 4. Insert the M8x20 mm screw through the washers and into the joint in the monitor arm. 5. Use the 6 mm hex key to tighten the screw.
Attach the column to the keyboard tray 1. Position the column with the cutout at the bottom half of the column. 2. Line up the assembly holes on the bottom of the column with the assembly holes between the holders on the keyboard tray.
3. On the underside of the keyboard tray, insert the four M6x12 mm screws through the keyboard tray and into the column. (figure 6) 4. Use the 5 mm hex key to tighten the screws in place.
Attach the column to the monitor arm 1. Insert one of the M6x10 mm screws into the top hole in the plate on the back of the column. (figure 7) Note: Do not tighten the M6x10 mm screw and make sure that you leave between 4 and 5 mm of space between the plate and the screw.
2. Hook the M6x10 mm screw attached to the column into the key-shaped hole at the top of the plate on the monitor arm.
3. Insert the M6x10 mm screws into the lower two holes on the plate on the monitor arm. (figure 9) 4. Use the 5 mm hex key to tighten all three of the screws.
Attach the VESA monitor mount to a monitor 1. If you want to be able to rotate your monitor 360°, use a Phillips type screwdriver to remove the screw from the VESA monitor mount.
2. Position the VESA monitor mount so that the projection on the back of the mount is pointing towards the bottom of the monitor. 3. Line up the VESA monitor mount with the mounting holes on the back of the monitor. 4. Insert the M4x10 mm screws through the VESA monitor mount and into the back of the monitor. 5. Use a Phillips type screwdriver to tighten the screws. (figure 11) Warning! Do not over-tighten the screws. If you encounter resistance while you’re tightening the screws, stop tightening.
Attach the monitor to the column 1. Carefully hook the back of the VESA monitor mount onto the plate on the column.
2. Insert the M6x8 mm screw through the bottom of the VESA monitor mount and into the plate on the column. 3. Use the 5 mm hex key to tighten the screw.
4. Slide the covers onto the wall plate.
Attach the adhesive strip 1. If necessary, cut the adhesive strip to fit the length of your keyboard. 2. Separate the two sides of the adhesive strip. 3. Remove the backing from one half of the adhesive strip and stick it to the back of your keyboard. 4. Remove the backing from the other half of the adhesive strip and stick it to the surface of the keyboard tray so that it lines up with the strip that you attached to your keyboard.
Route cables 1. Run your cable along the column and through the slot at the bottom of the column. 2. At the top of the cable cover, squeeze the tabs and gently pull the cable cover from the monitor arm. 3. Slide the cable cover up to unhook the tabs at the bottom of the cable cover from the slots in the monitor arm, and lift the cable cover off of the monitor arm. Caution! Be careful not to snap off the tabs from the cable cover when you remove it. 4. Run the cable along the inside of the cable cover.
Remove the monitor Warning: Stored energy hazard! The column contains a lift mechanism that could move up quickly when you remove the monitor from the product. Before you remove the monitor, move the monitor to the highest position. Failure to do so could result in injury or property damage. 1. Move the monitor to the highest position it can go. (figure 17) 2. Use the 5 mm hex key to remove the M6x8 mm screw from the bottom of the VESA monitor mount. 3. Carefully lift the monitor off of the monitor mount.
Adjusting the WALLSTS1 Adjust the tilt angle of the monitor • To increase or decrease the tilt, use the 2.5 mm hex key to adjust the screw in the top of the VESA monitor mount. (figure 18) figure 18 VESA monitor mount Adjustment screw 2.
Adjust the tilt angle of the keyboard tray • Pull up or push down on the keyboard tray to adjust it from 0 to 90°.
Counterbalance the weight of the monitor The WALLSTS1 features a one-touch height adjustment design that enables you to easily raise or lower your monitor. To use the one-touch height adjustment feature, you need to counterbalance the weight of your monitor. • If the monitor doesn’t stay in position when you move it or it’s difficult to raise or lower it, use the 5 mm hex key to turn the screw in the top of the column to the right or the left.
Counterbalance the weight of the workstation The WALLSTS1 features a one-touch height adjustment design that enables you to easily raise or lower the entire workstation, including the keyboard tray. To use the one-touch height adjustment feature, you need to counterbalance the weight of the workstation. Stored energy hazard! This product contains a lift mechanism that could move up quickly when you remove the mounted equipment. Before you remove the equipment, move the workstation to the highest position.
Adjust the swivel effort of the monitor arm • To increase or decrease the swivel effort of the monitor arm, use the 6 mm hex key to turn the screw in the plate on the back of the column to the right or left. (figure 22) Caution! When you loosen the screw, make sure that you don’t remove the screw from the joint. If you remove the screw, the column will fall off of the monitor arm and your equipment could be damaged or you could be injured.
Extend the keyboard tray You can adjust the keyboard tray so that it extends to the left or right. • Pull the extension to the left or right.
Clean the keyboard tray You can remove the extension and the plastic cover from the wrist rest to clean them. 1. To remove the plastic cover from the wrist rest, carefully peel it off of the keyboard tray. (figure 24) 2. To remove the keyboard tray extension, pull the extension all of the way out. On the underside of the keyboard tray, insert a blunt pin into one of the two holes, depress the clip, and pull the extension out of the keyboard tray. (figure 25) 3.
Technical support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. For the latest drivers/software, please visit www.startech.com/downloads Warranty information This product is backed by a two-year warranty. StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
