Height Adjustable Mobile Workstation - Single Monitor Actual product may vary from photos User Manual SKU#: WKSTNCART For the latest information and specifications visit www.startech.
Compliance Statements Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.
Safety Statements Safety Measures • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines. Mesures de sécurité • L’installation et/ou le montage du produit doit être réalisé par un professionnel certifié et dans le respect des normes locales et du code de construction local.
Warning Statements • Assemble this product according to the instructions. • Read the entire manual and ensure the instructions are fully understood before assembling and/or using this product. • Do not exceed the weight capacity of this product. Overloading this product might result in injury or property damage. • Weight capacity of the monitor mount: 8 kg (17.6 lb.) • Weight capacity of the keyboard tray: 2 kg (4.4 lb.) • Weight capacity of the CPU mount: 5 kg (11 lb.
• Produkten är endast avsedd för användning inomhus och ska inte användas utomhus. • Dra inte åt skruvarna för hårt när du monterar produkten. Om du måste ta i när du skruvar åt kan du sluta skruva åt. • Det krävs Monitorå personer för att montera produkten. Försök inte montera produkten och installera utrustning utan hjälp. • Innan du lägger till utrustning på produkten, se till att produkten är korrekt monterad, installerad och att produkten klarar av vikten på utrustningen som du lägger till.
注意 • 必ず取扱説明書に従って本製品の組み立てを行って下さい。 • 最初に取扱説明書を最後まで読み、本製品の組み立て方をすべて理解して から組み立て作業を始めて下さい。 • 本製品で定められた最大積載重量を超えないようにして下さい。最大積載 重量をオーバーした場合、怪我をする恐れや器物破損の恐れがあります。 • モニターマウントの耐荷重：8 kg（17.6ポンド） • キーボードトレイの耐荷重：2 kg（4.
• Durante l’assemblaggio del prodotto, non stringere troppo le viti. Se si incontra resistenza mentre si stringono le viti, interrompere l’operazione. • L’assemblaggio di questo prodotto richiede la presenza di due persone. Non tentare di assemblare il prodotto e installare le apparecchiature senza assistenza. • Prima di aggiungere altre apparecchiature al prodotto, assicurarsi di averlo assemblato e installato correttamente e che sia in grado di sostenere il peso dell’apparecchiatura in questione.
Mensagens de aviso • Certifique-se de que monta este produto de acordo com as instruções. • Leia todo o manual e certifique-se de que entende as instruções antes de começar a montar e a utilizar este produto. • Não exceda a capacidade de peso deste produto. Sobrecarregar este produto pode resultar em ferimentos ou danos de propriedade. • Capacidade de peso do suporte do monitor: 8 kg (17,6 lb.) • Capacidade de peso da bandeja do teclado: 2 kg (4,4 lb.) • Capacidade de peso da montagem da CPU: 5 kg (11 lb.
• Cuando ensamble este producto, no apriete los tornillos más de lo debido. Si al apretar los tornillos siente resistencia, no los apriete más. • Se requieren dos personas para el ensamblaje de este producto. No intente ensamblar este producto e instalar otros equipos sin la debida asistencia de otra persona. • Antes de instalar equipos en este producto, asegúrese de haberlo ensamblado correctamente, a fin de que pueda soportar el peso del equipo que vaya a instalar.
• Bewegen Sie den Wagen nicht über Leitungen, Kabel oder unebenes Gelände. • Stellen Sie sicher, dass die Rollen entriegelt sind, bevor Sie den Wagen in Bewegung setzen. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Table of Contents Compliance Statements.........................................................................i Safety Statements...................................................................................ii Warning Statements...............................................................................iii Product Diagram.....................................................................................1 Front View..................................................................................
Mount the Monitor to the Column (B)................................................................................................ 18 Adjust the Height of the CPU Holder Bracket.................................................................................. 19 Adjust the Width of the CPU Holder (D)............................................................................................. 20 Attach the CPU Holder (D) to the CPU Holder Bracket on the Column (B)............................................
Product Diagram Front View Column Cap (G) VESA Mount (H) Cable Management Slot Handles Keyboard Platform (F) Column (B) CPU Holder (D) Base (A) Casters (C) To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Product Dimensions Front View To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Keyboard Platform (F) View To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
CPU Holder (D) and CPU Straps (E) View Note: The CPU Straps (E) are not pre-installed. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Product Information Package Contents Note: The following images are not to scale. Base (A) Column (B) Caster (C) CPU Holder (D) Qty: 1 Qty: 1 Qty: 4 Qty: 1 CPU Straps (E) Keyboard Platform (F) Column Cap (G) VESA Mount (H) Qty: 2 Qty: 1 Qty: 1 Qty: 1 M8 x 30 mm Washers (Small) M6 x 6 mm Qty: 6 Qty: 4 (J) technical drawings, Screws (K) visit www.startech.
5 mm Hex Key (M) 6 mm Hex Key (N) Wrench (O) M4 x 12 mm Screws (M-A) Qty: 1 Qty: 1 Qty: 1 Qty: 4 M4 x 16 mm Screws (M-B) M5 x 12 mm Screws(M-C) M5 x 16 mm Screws (M-D) Washers (Large) (M-E) Qty: 4 Qty: 4 Qty: 4 Qty: 4 Spacers (M-F) M6 Wrench (P) M6 Nuts (Q) User Manual Qty: 4 Qty: 1 Qty: 2 Qty: 1 6
Technical Specifications Type of Measurement Measurement Screen Size Up to 32” Weight Capacity Monitor -- Up to 17.6 lb. (8 kg) Keyboard Platform -- Up to 4.4 lb. (2 kg) CPU mount: 11 lb. (5 kg) VESA Compatible 75 x 75 mm 100 x 100 mm To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Monitor Tilt Range +30° to -30° Monitor Rotation +180° to -180° Cable Management Yes To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Requirements For the latest requirements, please visit www.startech.com/WKSTNCART • Phillips Head Screwdriver x 1 Installation Note: Do not overtighten any of the screws. Attach the Caster (C) Figure 1 1. Figure 2 Flip the Base (A) upside down and place it onto a clean and flat surface. (Figure 1) Note: Cover hard floors with a soft cloth to prevent scratching. 2. Insert the four Caster (C) into the holes, located in the bottom of the Base (A) and tighten, using the Wrench (O). 3.
Attach the Column (B) to the Base (A) Figure 3 1. Insert the Column (B) into the Base (A). (Figure 3) 2. Thread four Washers (Small) (J) onto four M8 x 30 mm Screws (I). 3. Insert the four M8 x 30 mm Screws (I) through the bottom of the Base (A) and into the Column (B) and tighten, using the 5 mm Hex Key (M). To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Adjust the Height of the Column (B) Figure 4 Note: Always remove the Monitor prior to making any adjustments to the height of the Column (B). Up 1. Loosen the Locking Knob, located on the back of the Column (B), by twisting counterclockwise. (Figure 4) 2. Pull the Column (B) up to the desired height, using the attached Handles. 3. Tighten the Locking Knob, located on the back of the Column (B), by twisting clockwise. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.
Down 1. Loosen the Locking Knob, located on the back of the Column (B), by twisting counterclockwise. 2. Pull the Column (B) up slightly, using the attached Handles. Support the weight of the Column (B) and press and hold the Locking Knob to lower the Column (B). Note: Support the weight of the Column (B) during all height adjustments. The Column (B) will free fall if not properly supported once the Locking Knob has been pressed. 3.
1. Loosen (but do not remove) the Hex Screws in the Handles of the Column (B) and the Keyboard Platform Attachment Plate, using the 5 mm Hex Key (M). (Figure 5) 2. Adjust the Handles and the Keyboard Platform Attachment Plate to the desired heights and tighten the Hex Screws, loosened in step one, using the 5 mm Hex Key (M). Attach and Adjust the Keyboard Platform (F) Figure 6 Attach the Keyboard Platform (F) 1.
Adjust the Keyboard Platform (F) To slide the Keyboard Platform (F) towards or away from the User: 1. Loosen (but do not remove) the Wing Nuts located under the Keyboard Platform, by hand. 2. Slide the Keyboard Platform (F) to the desired position. 3. Tighten the Wing Nuts located under the Keyboard Platform, by hand. 4. (Optional - for secure Keyboard Platform (F) placement) Remove the Wing Nuts by hand, replace the Wing Nuts with the two M6 Nuts (Q), and tighten, using the 5.
1. Loosen (but do not remove) the Hex Screw located on the side of the VESA Mount (H), using the 6 mm Hex Key (N). (Figure 7) 2. Tilt the VESA Mount (H) down to access the top-back Mounting Hole. Insert an M8 x 30 mm Screw (I) through the Mounting Hole located at the top-back of the VESA Mount and into the Column (B) then tighten, using the 5 mm Hex Key (M). 3. Tilt the VESA Mount (H) upwards to access the top-back Mounting Hole.
1. Remove the Thumbscrew from the top of the VESA Mount (H). Save this Thumbscrew for a future installation step. (Figure 8) 2. Slide the VESA Plate up and off of the VESA Mount (H). Attach the VESA Plate to the Monitor Figure 9 1. Place the Monitor on a padded surface, screen side down, so the back of the Monitor is accessible. (Figure 9) 2. (Optional) Identify and remove the pre-installed VESA Hardware from the back of the Monitor. Note: Not all Monitors will have placeholder VESA Hardware.
3. (Optional -- for Monitors with recessed VESA Mounting Holes, for Monitors with uneven rear geometry, or to adjust the engagement depth of the provided Screws) Add the necessary number of Spacers (M-F) between the Monitor and the VESA Plate. 4. Align the VESA Plate over the VESA Mounting Holes or (optional) Spacers (M-F) located on the back of the Monitor. The side of the VESA Plate that features the threaded hole should be pointing towards the top of the Monitor. 5.
Mount the Monitor to the Column (B) Figure 10 1. (Complete this step with two people) Lift the Monitor Assembly and slide the VESA Plate down into the tracks on the VESA Mount (H) to align the screw hole located on the top of the VESA Plate with the hole located on the top of the VESA Mount (H). (Figure 10) 2. Insert the Thumbscrew, removed in step one of Remove the VESA Plate from the VESA Mount (H), through the screw hole located on the top of the VESA Plate and into the VESA Mount (H). 3.
Adjust the Height of the CPU Holder Bracket Figure 11 1. Loosen (but do not remove) the four Hex Screws located on the sides of the CPU Holder Bracket, using the 5 mm Hex Key (M). (Figure 11) 2. Slide the CPU Holder Bracket to the recommended mounting height of 80 - 120 mm from the floor. 3. Tighten the four Hex Screws located on the sides of the CPU Holder Bracket, using the 5 mm Hex Key (M). Ensure the Hex Screws are fastened enough to support the weight of the CPU.
Adjust the Width of the CPU Holder (D) Figure 12 1. Twist the Knobs located on the bottom of the CPU Holder (D) in a counterclockwise direction to loosen. (Figure 12) 2. Adjust the CPU Holder (D) to the width of the CPU. 3. Twist the Knobs located on the bottom of the CPU Holder (D) in a clockwise direction to tighten. Attach the CPU Holder (D) to the CPU Holder Bracket on the Column (B) Figure 13 To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
1. Hang the CPU Holder (D) onto the Hooks, located on the CPU Holder Bracket on the Column (B). (Figure 13) 2. Insert two M6 x 6 mm Screws (K) through the CPU Holder (D) and into the CPU Holder Bracket on the Column (B) then tighten, using a Phillips Head Screwdriver. Attach the CPU Straps (E) to the CPU Holder (D) Figure 14 Push the t-shaped end of the CPU Straps (E) through the slots on the back of the CPU Holder (D).
Install/Secure the CPU into the CPU Holder (D) Figure 15 1. Feed the secondary portions of the CPU Straps (E) through the slots on the front of the CPU Holder (D). 2. Feed the CPU Straps (E) back into themselves through the Folding Plastic Clips located on the primary portion of the CPU Straps (E). As the CPU Straps (E) are being fed into themselves the Folding Plastic Clip will unfold. After completing any necessary adjustments, fold the Folding Plastic Clip to lock the CPU Straps (E). 3.
Cable Management Figure 16 Route the Cables from the CPU down through the Base (A) and out of the Cable Management Slot located in the Column (B). Store the 5 mm (M) / 6 mm (N) Hex Keys Slide the Hex Keys into the storage slots located on either side of the middle of the Column (B). Operation Move the Mobile Workstation Assembly 1. Unplug all the Cables connecting the Mobile Workstation to any Stationary Object (e.g. the wall, a media device, etc.). 2. Disengage the Brakes on the Casters (C).
3. Grip the Monitor and the Handles on the Column (B) and slowly move the Mobile Workstation Assembly, using two people. Ensure caution is exercised around corners or when navigating over bumps and/or uneven ground. 4. Lock the Brakes on the Casters (C). To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Warranty Information This product is backed by a two-year warranty. For further information on product warranty terms and conditions, please refer to www.startech.com/warranty. Limitation of Liability In no event shall the liability of StarTech.com Ltd. and StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
