Installation Manual

ManualsBrandsState Industries ManualsElectric Heater200 Series

THIS PRINTOUT IS FOR REFERENCE ONLY!

Do not use this printout for color match or critical dimensions.

Printout made at 65% of final size.

THIS FILE HAS NOT BEEN TRAPPED.

This file was created with Adobe Illustrator CS.

DO NOT try to open this file with earlier versions.

Marketing Support Inc. assumes no responsibility for final print quality and

will not be held liable for errors or omissions due to alterations made to this

document by client, film or print vendor.

MSI requires a Chromalin or color key type proof for final approval.

If you have any questions about this file, or require further assistance,

contact MSI at 312-565-0044 .

Front

For Additional Technical Information,

PHONE 800-365-0024

STATE WATER HEATERS

500 Tennessee Waltz Parkway, Ashland City, TN 37015

www.statewaterheaters.com

Page 1 of 2

SRGSS00905 REV1

Power-Vent Design – System allows for installation flexibility with

combined horizontal and vertical venting runs using Schedule 40 PVC,

CPVC or ABS pipe.

Intelli-Vent

™

Gas Control – Equipped with nearly indestructible

silicon nitride hot surface igniter, and advanced electronics for precise

temperature control and easy-to-understand system diagnostics. Gas

connection located on side of control, same as conventional gas control.

Modular Blower

– Equipped with 110/120 volt electrical system

(rating 3 amps or less), 6-foot cord, standard 3-prong male connector.

Diffuser Dip Tube – Helps reduce lime and sediment buildup, maximizes

hot water output. Made of State PEXAN

, a cross-link PEX polymer that can

withstand long-term exposure to water temperatures up to 400ºF.

Green Choice

Eco-Friendly Gas Burner – Patented design reduces NOx

emissions up to 33% and complies with Southern California and Texas requirements.

Durable Brass Tamper-Resistant Drain Valve.

Glass-Lined Tank

– For long-lasting protection against rust and corrosion.

Aluminum Anode Rod – For additional protection against rust and corrosion.

Factory-Installed Temperature & Pressure (T&P) Relief Valve.

Thick, CFC-Free Foam Insulation.

SELECT

POWER-VENT

Residential Gas Water Heaters

6-Year Ta nk Warranty • 6-Year Parts Warranty

Code Compliance – All models meet or exceed federal minimum energy standards

effective January 20, 2004, according to latest editions of the National Appliance

Energy Conservation Act (NAECA). They also comply with the latest editions of the

B.O.C.A. National Codes, C.E.C., U.B.C., S.B.C.C., C.A.B.O. and the H.U.D. standards.

All models design-certiﬁed by CSA International according to ANS Z21.10.1 standards

governing storage-type water heaters.

200 Series Model

Summary of content (2 pages)

PAGE 1
SELECT ® POWER-VENT Residential Gas Water Heaters 6-Year Tank Warranty • 6-Year Parts Warranty Power-Vent Design – System allows for installation flexibility with combined horizontal and vertical venting runs using Schedule 40 PVC, CPVC or ABS pipe. Intelli-Vent™ Gas Control – Equipped with nearly indestructible silicon nitride hot surface igniter, and advanced electronics for precise temperature control and easy-to-understand system diagnostics.
PAGE 2
SELECT ® POWER-VENT Residential Gas Water Heaters 6-Year Tank Warranty • 6-Year Parts Warranty FIRST HOUR RATING GALLONS ENERGY FACTOR PR6 40 XCVIT 79 PR6 50 XCVIT PR6 40 XCVIT 2 DIMENSIONS IN INCHES GAL. CAP. BTU INPUT PER HOUR NATURAL RECOVERY 90°F RISE GALLONS PER HOUR R VALUE .62 40 40,000 41 8 89 .62 50 40,000 41 79 .64 40 40,000 41 PR6 50 XCVIT 2 89 .64 50 40,000 41 PR6 50 XCVIT 5 103 .62 50 65,000 GS6 75 YRVIT N/A N/A 74 80,000 MODEL NUMBER APPROX.