User Manual

ManualsBrandsState ManualsWater boilerGTS-110-NI



‐Do not store or use gasoline or other

flammablevaporsandliquidsinthevicinityof

thisoranyotherappliance.

‐WHATTODOIFYOUSMELLGAS

 Donottrytolightanyappliance.

 Do not touch any electric switch, do not

useanyphonein

yourbuilding.

 Immediatelycallyourgassupplierfroma

neighbor's phone. Follow the gas

supplier'sinstructions.

 Ifyoucannotreachyourgassupplier,call

thefiredepartment.

‐Installation and service must be performed

byaqualifiedinstaller,serviceagencyorthe

gassupplier.



FEATURING

 ENDLESSHOTWATER

 ONDEMANDUSAGE

 COMPACT,SPACESAVING

 ENERGYCONSERVATION

 COMPUTERIZEDSAFETY

 NOPILOTLIGHT

 EASY‐LINKSYSTEM

510(T‐D2)modelsonly

GasTanklessWaterHeater

Suitableforpotablewater heating andspace‐hea ting

*

*Pleaserefertolocalcodesforspace‐heatingcompliance.

Ifyouhaveanyquestions,please

callorwriteto:

500TennesseeWaltzParkway

AshlandCity,TN37015

TollFree:1‐ 877‐737‐2840

On‐DemandWaterHeater

InstallationManualandOwner’sGuide

Models

・

110Indoor(T‐KJr2‐IN)

・

110Outdoor(T‐KJr2‐OS)

・

310Indoor(T‐K4‐IN)

・

310Outdoor(T‐K4‐OS)

・

510Indoor(T‐D2‐IN)

・

510Outdoor(T‐D2‐OS)

WARNING

Iftheinformationinthese

instructionsisnotfollowed

exactly,afireorexplosion

mayresultcausing

propertydamage,personalinjuryordeath.

ANSI Z21.10.3 andCSA4.3

510(T‐D2)models

only

Summary of content (52 pages)

PAGE 1
On‐Demand Water Heater Installation Manual and Owner’s Guide ANSI Z21.10.3 and CSA 4.3 Models 510 (T‐D2) models only ・110 Indoor (T‐KJr2‐IN) ・110 Outdoor (T‐KJr2‐OS) ・310 Indoor (T‐K4‐IN) ・310 Outdoor (T‐K4‐OS) ・510 Indoor (T‐D2‐IN) ・510 Outdoor (T‐D2‐OS) If the information in these instructions is not followed exactly, a fire or explosion WARNING may result causing property damage, personal injury or death.
PAGE 2
Contents CONTENTS Installation Manual SPECIFICATIONS…………………………………………………………………………………………..………………………... 3 INTRODUCTION…………………………………………………………………………………………………..…………………. 4 SAFETY GUIDELINES…………….………………………………………………………………………………………..……….. 5 INSTALLATION………………………………………………………………………………………………..…………………..…. 6 General………………………………………………………………………………………………………………………..…..… 6 Warning for Installations………………………………………………………………………………………………………8 Clearances…………………………………………………………………………………………………………………………… 9 Included Accessories…………….
PAGE 3
Specifications Installation Manual SPECIFICATIONS Model Natural Gas Input (Operating Range) Propane Input (Operating Range) 110 110 Outdoor Indoor (T‐KJr2‐IN) (T‐KJr2‐OS) Min: 19,500 Btu/h Max: 140,000 Btu/h 310 310 Outdoor Indoor (T‐K4‐IN) (T‐K4‐OS) Min: 11,000 Btu/h Max: 190,000 Btu/h 510 510 Indoor Outdoor (T‐D2‐IN) (T‐D2‐OS) Min: 11,000 Btu/h Max: 199,000 Btu/h Min: 19,500 Btu/h Max: 140,000 Btu/h Min: 11,000 Btu/h Max: 190,000 Btu/h Min: 11,000 Btu/h Max: 199,000 Btu/h Gas Connection ¾” NPT W
PAGE 4
Introduction INTRODUCTION  This manual provides information necessary for the installation, operation, and maintenance of the water heater.  The model description is listed on the rating plate which is attached to the front panel of the water heater.  Please read all installation instructions completely before installing this product.  If you have any problems or questions regarding this equipment, consult with the manufacturer or its local representative.
PAGE 5
Safety Guidelines SAFETY GUIDELINES SAFETY DEFINITIONS Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. DANGER Indicates an imminently hazardous situation which, if not avoided, could result in death or serious injury. WARNING Indicates an imminently hazardous situation which, if not avoided, could result in minor or moderate injury. CAUTION GENERAL 1. 2. 3. 4. 5.
PAGE 6
Installation INSTALLATION GENERAL 1. Follow all local codes, or in the absence of local codes, follow the most recent edition of the National Fuel Gas Code: ANSI Z223.1/NFPA 54 in the USA or CAN/CSA B149.1 Natural Gas, Propane Installation Code in Canada. 2. All gas water heaters require careful and correct installation to ensure safe and efficient operation. This manual must be followed exactly. Read the “Safety Guidelines” section. 3. The manifold gas pressure is preset at the factory.
PAGE 7
Installation  Installation and service must be performed by a qualified installer (for example, a licensed plumber or gas fitter), otherwise the warranty will be void. WARNING  The installer (licensed professional) is responsible for the correct installation of the water heater and for compliance with all national, state/provincial, and local codes.  The manufacturer does not recommend installing the water heater in a pit or location where gas and water can accumulate.
PAGE 8
Installation WARNING FOR INSTALLATIONS FOR YOUR SAFETY, READ BEFORE INSTALLATION: Do not install the heater where water, debris or flammable vapors may get into the flue terminal. This may cause damage to the heater and void the warranty. Do not have the vent terminal pointing toward any opening into a building. Do not locate your heater in a pit or location where gas and water can accumulate.
PAGE 9
Installation CLEARANCES Top Side Maintain all clearances around the water heater.
PAGE 10
Installation 1. Temperature Remote Controller: 9007666005 2. Temperature Remote Controller: 9007603005 (TK‐RE02) (TM‐RE30) The Temperature Remote Controller has two functions. It allows the output temperature from the water heater to be adjusted within the range of 99 °F to 167 °F, and it also works as a diagnostic tool that will give a concise error code whenever there is a problem with the unit.
PAGE 11
Installation HIGH‐ALTITUDE INSTALLATIONS Check the elevation where your water heater is installed. Set dipswitches shown in the table below depending on the altitude. 110 (T‐KJr2) and 310 (T‐K4) models 0 to 2,000 ft (DEFAULT) OFF OFF Altitude Switch No.3 Switch No.
PAGE 12
Installation VENTING INSTRUCTIONS ‐General‐ Improper venting of this appliance can result in excessive levels of carbon monoxide which can result in severe personal injury or death. DANGER CAUTION Improper installation can cause nausea or asphyxiation, severe injury or death from carbon monoxide and flue gases poisoning. Improper installation will void product warranty. When installing the vent system, all applicable national and local codes must be followed.
PAGE 13
Installation ‐Exhaust venting‐ For the 110 Indoor (T‐KJr2‐IN), 310 Indoor (T‐K4‐IN) and 510 Indoor (T‐D2‐IN) models This is a Category III appliance and must be vented accordingly. The vent system must be sealed air tight. All seams and joints without gaskets must be sealed with high heat resistant silicone sealant or UL listed aluminum adhesive tape having a minimum temperature rating of 350°F. For best results, a vent system should be as short and straight as possible.
PAGE 14
Installation Horizontal Installation Diagram (With direct‐venting) Vertical Installation Diagram (With direct‐venting) Rain Cap Wall Roof Roof Flashing Sidewall Vent Terminator Backflow Preventer * Backflow Preventer * Fire stop Vertical Condensation Drain** Vertical Condensation Drain** See the picture below for detailed connection instructions to the Direct‐Vent Conversion Kit.
PAGE 15
Installation ‐Vent termination clearances‐ Canada Direct vent and other than Direct Vent U.S.A Direct vent Other than Direct Vent 1 foot A Clearance above grade, veranda, porch, deck, or balcony. 1 foot 1 foot B Clearance to window or door that may be opened. 3 feet 1 foot C 4 feet from below or side opening. 1 foot from above opening.
PAGE 16
Installation Please follow all local and national codes in regards to proper termination clearances. In the absence of such codes, the following clearances can be used as guidelines. Local CAUTION codes supersede these guidelines. For sidewall terminations 2ft. 3ft. 1ft. 1ft. 2ft. 1ft. 3ft. 1ft. 3ft. Inside corner Exhaust termination For multiple sidewall exhaust terminations (e.g. multi‐unit systems), an exhaust termination must be at least 1 ft. away from another exhaust termination.
PAGE 17
Installation GAS SUPPLY AND GAS PIPE SIZING ‐General‐   WARNING  Check that the type of gas matches the rating plate first. Ensure that any and all gas regulators used are operating properly and providing gas pressures within the specified range shown below. Excess gas inlet pressure may cause serious accidents. Conversion of this unit from natural gas to propane or vise versa will void all warranty. Contact your local distributor to get the correct unit for your gas type.
PAGE 18
Installation ‐Natural Gas Supply Piping‐ Maximum Delivery Capacity of Cubic Feet of Gas per Hour of IPS Pipe Carrying Natural Gas of 0.60 Specific Gravity Based on Pressure Drop of 0.5” WC Based on Energy Content of 1,000 BTU/Cubic Ft.: The water heater requires 140 Cubic Ft./hr for the 110 (T‐KJr2) models, 190 Cubic Ft./hr for the 310 (T‐K4) models, and 199 Cubic Ft./hr for the 510 (T‐D2) models.
PAGE 19
Installation ‐Measuring inlet gas pressure‐ 1. Turn off all electric power to the water heater if service is to be performed. 2. Turn the manual gas valve located on the outside of the unit clockwise  to the off position. The water heater cannot perform properly without sufficient inlet gas pressure. Below are instructions on how to check the inlet gas pressure. THIS IS ONLY TO BE DONE BY A LICENSED PROFESSIONAL. 1. Shut off the manual gas valve on the supply gas line. 2.
PAGE 20
Installation WATER CONNECTIONS  CAUTION  Do not use this water heater if any part has been submersed under water. Immediately call a licensed professional to inspect the water heater to replace any damaged parts. Do not reverse the hot outlet and cold inlet connections to the water heater. This will not properly activate the water heater. All pipes, pipe fittings, valves and other components, including soldering materials, must be suitable for potable water systems. 1. 2. 3. 4.
PAGE 21
Installation ELECTRICAL CONNECTIONS WARNING CAUTION Follow the electrical code requirements of the local authority having jurisdiction. In the absence of such requirements, follow the latest edition of the National Electrical Code ANSI/NFPA 70 in the U.S. or the latest edition of CSA C22.1 Canadian Electrical Code, Part 1, in Canada. When servicing or replacing parts within the water heater, label all wires prior to disconnection to facilitate an easy and error‐free reconnection.
PAGE 22
Installation REMOTE CONTROLLER CONNECTIONS 1. 2. 3. Disconnect power supply from the water heater. Take off the water heater’s front cover. Locate the remote controller terminal, pictured below (located around the lower right‐hand side of the computer board). 4. Open the plastic cover of the remote controller, and then attach the two fork terminals to connector base of the backside the remote controller with two screws.
PAGE 23
Installation PUMP CONTROL CONNECTIONS Available on the 510 (T‐D2) models only The 510 (T‐D2) models water heaters can be used to control a recirculation pump. Proper pump control helps to preserve the life of the system and saves energy as well. The water heater pump control port is a “normally open dry contact”, and therefore needs additional components to properly control a recirculation pump.
PAGE 24
Installation EASY‐LINK SYSTEM Available on the 510 (T‐D2) models only ‐General‐ The 510 (T‐D2) models water heaters can be connected with other heaters of the same model with communication cables to work as a multiple‐unit manifold system.  The Easy‐Link system allows up to 4 units to manifold together.  A communication cable (gray color) comes with each 510 (T‐D2) models. You can manifold from 2 to 4 units without the need for a multi‐system controller.
PAGE 25
Installation 4. Between the “PARENT” and the “CHILD‐1” units Connect the “PARENT” connector of the “PARENT” unit to the “[1]” connector of the “CHILD‐1” unit. 5. Between the “CHILD‐1” and the “CHILD‐2” units Connect the “[2]” connector of the “CHILD‐1” unit to the “[1]” connector of the “CHILD‐2” unit. 6. Between the “CHILD‐2” and the “CHILD‐3” units Connect the “[2]” connector of the “CHILD‐2” unit to the “[1]” connector of the “CHILD‐3” unit. 7. Make sure the 7‐seg.
PAGE 26
Installation  NOTICE   A remote controller is not required for the Easy‐Link system. If running the Easy‐Link system without a remote controller, please make sure the temperature settings on ALL the units are set to the same settings. Otherwise, the units will not operate properly. If a remote controller is used, the temperature on all the units in the system will automatically be set to the same temperature that is set on the remote.
PAGE 27
Installation CASE 3:  If you connect the “PARENT” connector of the “CHILD‐1” unit to the “[1]” connector of the “CHILD‐2” unit, the “CHILD‐2” unit will operate as an individual unit, and will not be part of the Easy‐Link system.
PAGE 28
Installation APPLICATIONS ‐Space‐Heating Applications‐  WARNING      In order to purge air in water pipes within a closed‐loop system, an air vent and air separator should be installed in to the system. Required circulation flow rates are labeled next to each application diagram. These flow rate requirements must be followed.
PAGE 29
Installation ‐Dual‐purpose hot water heating‐ (Domestic and Space Heating): Diagramatic Layout of Radiant Heating and Domestic Water Heater Per Mass.
PAGE 30
Initial Operation INITIAL OPERATION FOR YOUR SAFETY, READ BEFORE OPERATING  Check the GAS and WATER CONNECTIONS for leaks before firing unit for the first time.  Open the main gas supply valve to the unit using only your hand to avoid any spark. Never use tools. If the knob will not turn by hand, do not try to force it; call a qualified service technician. Forced repair may result in a fire or explosion due to gas leaks.
PAGE 31
Operating Safety Ow n er’ s Gu id e OPERATING SAFETY FOR YOUR SAFETY READ BEFORE OPERATING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This water heater does not have a pilot. It is equipped with an ignition device that automatically lights the burner. Do not try to light the burner by hand. B. BEFORE OPERATING smell all around the water heater area for evidence of leaking gas.
PAGE 32
Operating Safety DANGER Vapors from flammable liquids will explode and catch fire causing death or severe burns. Do not use or store flammable products such as gasoline, solvents or adhesives in the same room or area near the water heater. Keep flammable products: 1. Far away from heater 2. In approved containers 3. Tightly closed 4. Out of children's reach Vapors: 1. Cannot be seen 2. Vapors are heavier than air 3. Go a long way on the floor 4.
PAGE 33
Normal Operation NORMAL OPERATION GENERAL WARNING NOTICE  Hot Water temperatures over 125°F (52°C) can cause severe burns instantly or death from scalding.  The outlet hot water temperature of the water heater is factory set at 122°F (50°C).  Feel the water temperature before bathing or showering.  Flow rate to activate the water heater  Flow rate to keep the water heater running 1. Open a hot water tap.* : 0.5 gallons per minute at the default set temperature : 0.4 gallon per minute 2.
PAGE 34
Normal Operation ‐Dipswitch settings for each temperature on the computer board‐ 110 (T‐KJr2) and 310 (T‐K4) models Temperature Settings 113 F ON (45 C) OFF 1 2 3 4 5 6 7 8 122 F (50 C) DEFAULT 1 2 3 4 5 6 7 8 ON OFF 131 F ON (55 C) OFF 1 2 3 4 5 6 7 8 140 F ON (60 C) OFF 1 2 3 4 5 6 7 8 510 (T‐D2) models Temperature Settings 104 F ON (40 C) OFF 140 F ON (60 C) OFF 1 2 3 4 5 6 1 2 3 4 5 6 113 F ON (45 C) OFF 158 F ON (70 C) OFF 1 2 3 4 5 6 12
PAGE 35
Normal Operation FLOW  The flow rate through the water heater is limited to a Household Flow Rates maximum of 6.6 GPM for the 110 (T‐KJr2) models, 8.0 Appliance / Use Flow Rate (GPM) GPM for the 310 (T‐K4) models, and 10.0 GPM for the Lavatory Faucet 1.0 510 (T‐D2) models. Bath Tub 4.0 – 10.0  The temperature setting, along with the supply Shower 2.0 temperature of the water will determine the flow rate Kitchen Sink 1.5 output of the unit.  Please refer to the temperature vs.
PAGE 36
Normal Operation MAINTENANCE AND SERVICE WARNING Turn off the electrical power supply and close the manual gas shutoff valve and the manual water control valve before servicing.      Clean the cold‐water inlet filter. (Refer to diagram below) Be sure that all openings for combustion and ventilation air are not blocked. The venting system should be checked annually for any leaks, corrosion, blockages or damage. The burner should be checked annually for dust, lint, grease or dirt.
PAGE 37
Troubleshooting TROUBLESHOOTING GENERAL PROBLEM It takes long time to get hot water at the fixtures. SOLUTIONS  The time it takes to deliver hot water from the water heater to your fixtures depends on the length of piping between the two. The longer the distance or the bigger the pipes, the longer it will take to get hot water.  If you would like to receive hot water to your fixtures quicker, you may want to consider a hot water recirculation system. (p.
PAGE 38
Troubleshooting PROBLEM ‐EASY‐LINK SYSTEM‐ 510 (T‐D2) models only ‐Remote controller‐ (OPTIONAL)‐ ‐ WATER HEATER ‐ Unit does not ignite when water goes through the unit. SOLUTIONS  Is the flow rate over 0.5 GPM? (p. 33)  Check for the filter on cold water inlet. (p. 36)  Check for reverse connection and cross connection.  If you use the remote controller, is the power button turned on?  Check if the inlet temperature is too high. The fan motor is still spinning after operation has stopped.
PAGE 39
Troubleshooting ERROR CODES    The units are self diagnostic for safety and convenience when trouble shooting. If there is a problem with the installation or the unit, depending on the model or if there is a remote controller installed, it will either display a numerical error code on the 7‐Seg LED on the computer board (for the 510 (T‐D2) models only), display a blinking red LED (for the 110 (T‐KJr2) and 310 (T‐K4) models), or the error code will display on the remote controller if it is installed.
PAGE 40
Troubleshooting ‐FAULT ANALYSIS OF ERROR CODES‐ If the error code displayed on the computer board of the Water heater or remote controller, please check the following. After checking, Consult with the manufacturer. 110 (T‐KJr2) and 310 (T‐K4) Red LED One Time 510 (T‐D2) Remote Remote Malfunction description Diagnosis  Check the dipswitch settings on the PCB. (Part #701)  Check the gas type of the water heater.  Check if there is any blockage in the intake air and/or exhaust.
PAGE 41
Troubleshooting 110 (T‐KJr2) and 310 (T‐K4) Red LED 510 (T‐D2) Remote Remote Malfunction description Diagnosis Flow Sensor  Check for connection/breakage of wires and/or debris Failure (Easy‐Link on the flow sensor impeller.
PAGE 42
Components Diagram COMPONENTS DIAGRAM Case assembly 110 Indoor (T‐KJr2‐IN) 110 Outdoor (T‐KJr2‐OS) 052 003 052 052 004 004 007 007 053 052 001 001 702 702 052 052 002 721 704 002 720 006 066 051 053 056 704 005 050 052 050 310 and 510 Outdoor (T‐K4‐OS and T‐D2‐OS) 310 and 510 Indoor (T‐K4‐IN and T‐D2‐IN) 052 003 052 052 004 004 007 007 001 001 053 052 702 702 052 052 002 002 721 704 720 006 051 066 053 056 704 005 050 050 052 110 (T‐KJr2) models and 310 (T‐K
PAGE 43
Components Diagram Burner assembly 110 (T‐KJr2) models Burner assembly 101 107 110 106 105 108 065 104 709 109 111 401 712 059 053 052 706 053 121 703 053 059 704 112 705 103 053 113 114 150 708 701 Manifold assembly 053 058 713 115 102 O n l y(T‐KJr2‐IN) T - K J r 2 - Ionly N 110 Indoor 061 053 067 119 120 151 053 055 711 062 118 712 714 055 053 43│Page 052
PAGE 44
Components Diagram 310 (T‐K4) models and 510 (T‐D2) models Burner assembly 101 107 106 105 108 065 104 709 109 110 111 401 712 053 T-K4 -IN 310 (T‐K4) T-K4-OS models Power control section 121 706 053 703 A 053 052 116 704 117 705 053 510 (T‐D2) T - D models 2-IN T-D2-OS 053 103 121 054 112 706 703 A 053 704 115 113 705 057 114 058 053 150 701 708 A Manifold assembly 053 713 T-K4-IN 310 Indoor (T‐K4‐IN) T-D2-IN 510 Indoor (T‐D2‐IN) Fan motor section for indoor models
PAGE 45
Components Diagram Computer board Assembly 110 (T‐KJr2) and 310 (T‐K4) models 710 510 (T‐D2) models 701 103 708 701 707 717 103 707 718 710 709 402 402 708 716 714 715 709 719 408 407 719 Water way assembly 310 (T‐K4) models 110 (T‐KJr2) models 510 (T‐D2) models 463 463 463 453 413 453 413 453 413 452 450 452 452 414 450 450 414 414 412 412 412 063 063 063 401 401 401 B 451 414 454 C 414 411 459 414 403 B B 462 Bypass section 458 C C 460 451 451
PAGE 46
Output Temperature Chart PARTS LIST Item# Description 001 Case assembly for 110 Indoor (T‐KJr2‐IN) for 110 Outdoor (T‐KJr2‐OS) for 310 and 510 Indoor (T‐K4‐IN and T‐D2‐IN) for 310 and 510 Outdoor (T‐K4‐OS and T‐D2‐OS) Front cover for 110 Indoor (T‐KJr2‐IN) for 110 Outdoor (T‐KJr2‐OS) for 310 Indoor (T‐K4‐IN) for 310 Outdoor (T‐K4‐OS) for 510 Indoor (T‐D2‐IN) for 510 Outdoor (T‐D2‐OS) Air blockage plate for 110 Indoor (T‐KJr2‐IN), 310 Indoor (T‐K4‐IN) and 510 Indoor (T‐D2‐IN) Bracket Junction box Junctio
PAGE 47
Output Temperature Chart Item# Description 104 Burner holder gasket for 110 (T‐KJr2) models Burner holder gasket for 310 (T‐K4) and 510 (T‐D2) models Burner gasket Burner window Rod holder gasket Flame rod for 110 (T‐KJr2) models Flame rod for 310 (T‐K4) and 510 (T‐D2) models Igniter rod for 110 (T‐KJr2) models Igniter rod for 310 (T‐K4) and 510 (T‐D2) models Rod holder for 110 (T‐KJr2) models Rod holder for 310 (T‐K4) and 510 (T‐D2) models Rod cap Burner damper for 110 (T‐KJr2) models Burner damper for
PAGE 48
Output Temperature Chart Item# Description 408 Outlet thermistor for 110 (T‐KJr2) and 310 (T‐K4) models Mixing thermistor for 510 (T‐D2) models Water outlet Outlet drain plug Output thermistor for 510 (T‐D2) models Hi‐Limit switch for 110 (T‐KJr2) and 310 (T‐K4) models Hi‐Limit switch for 510 (T‐D2) models Overheat‐cut‐off fuse Heater Inlet heater Pipe heater fixing plate Heater fixing plate 16 Fuse fixing plate 18 Fuse fixing plate 14 O‐ring P4 FKM O‐ring P6 FKM O‐ring P14 FKM O‐ring P15 FKM O‐ring P16
PAGE 49
Output Temperature Chart Item# Description 713 Freeze protection thermostat for 110 Indoor (T‐KJr2‐IN), 310 Indoor (T‐K4‐IN) and 510 Indoor (T‐D2‐IN) Proportional gas valve wire for 110 (T‐KJr2) and 310 (T‐K4) models Proportional gas valve wire for 510 (T‐D2) models Pump and multi cable for 510 (T‐D2) models Thermistors wire for 510 (T‐D2) models RS‐VG wire for 510 (T‐D2) models Water valves wire for 510 (T‐D2) models Computer board cover for 110 (T‐KJr2) and 310 (T‐K4) models Computer board cover for 5
PAGE 50
Output Temperature Chart 310 (T‐K4) models Output Temperature vs. GPM (Max. 8.0 GPM) with Various Inlet Water Temperature Out Put Hot Water GPM 10.0 40 F 8.0 50 F 60 F 70 F 6.0 4.0 2.0 0.0 100 105 110 115 120 125 130 135 140 150 160 165 40 F 5.2 4.8 4.4 4.1 3.9 3.7 3.5 3.3 3.1 2.8 2.6 2.5 50 F 6.2 5.7 5.2 4.8 4.4 4.1 3.9 3.7 3.5 3.1 2.8 2.7 60 F 7.8 6.9 6.2 5.7 5.2 4.8 4.4 4.1 3.9 3.5 3.1 3.0 70 F 8.0 8.0 7.8 6.9 6.2 5.7 5.2 4.8 4.4 3.
PAGE 51
Warranty LIMITED WARRANTY 1. General terms of limited warranty: This limited warranty gives you specific legal rights, and you may also have other rights which vary from State to State. The manufacturer will honor the warranty to the original retail buyer at the original location only, and it is not transferable.
PAGE 52
Warranty (3) Limited Labor Coverage  The manufacturer will provide for reasonable labor charges associated with warranty repairs or replacements within one (1) year from the date of purchase. The manufacturer will only pay directly to the service provider.  Warranty service must be performed by an authorized Service Representative. A list of authorized Service Representatives is available upon request.  All warranty claims and warranty service must be authorized and approved by the manufacturer.