PN# 100171-03 Water Meter Interface Final Assembly Procedures Document # 8000171-60-01 March 11, 2003 Confidential Document This is a confidential document which is owned and Copyrighted by StatSIGNAL Systems, Inc., which reserves all its rights. This document may be reproduced only with the express written permission of StatSIGNAL Systems, Inc. © Copyright 2002, StatSIGNAL Systems, Inc.
Final Assembly Procedures 100171-03 Water Meter Interface March 11, 2003 Document 8000171-60-01 Page i SIGN OFF PAGE Engineering Manager: Executive Vice President: Print Name: Print Name: Signature: Signature: Date: Date: Production Manager: Print Name: Signature: Date: © Copyright 2003, StatSignal Systems, Inc.
Final Assembly Procedures 100171-03 Water Meter Interface March 11, 2003 Document 8000171-60-01 Page ii Revision History Date Revision Description Author 11/15/02 00 First Draft J. Davis, E. Ocheseanu, H. Westergren 11/20/02 00 2nd Draft H. Westergren, J. Davis 11/25/02 00 3rd Draft J. Davis, E. Ocheseanu, H. Westergren 03/11/03 01 Changed Base Assembly I & II procedure; Released for Production H. Westergreen E. Ocheseanu © Copyright 2003, StatSignal Systems, Inc.
Final Assembly Procedures 100171-03 Water Meter Interface March 11, 2003 Document 8000171-60-01 Page iii Table of Contents 1. SCOPE................................................................................................................................................................1 2. REFERENCES ....................................................................................................................................................1 3. SAFETY PRECAUTIONS...........................
100171-03 Water Meter Interface Final Assembly Procedures March 11, 2003 1. 8000171-60-01 Page 1 SCOPE This document provides the procedures required to safely and efficiently install the 200171-xx Water Meter Circuit Board Assembly with a 171404-xx battery assembly into the 171400xx enclosure to produce the 100171-xx finished good Water Meter used by StatSIGNAL Systems, Inc. 2. REFERENCES 3.
100171-03 Water Meter Interface Final Assembly Procedures March 11, 2003 8000171-60-01 Page 2 (222051) k. 1 each 3ft. long 22/3-AWG wire asby. (222056) l. 1 each paper tie (999110) 4.2 Tools The following tools are required to enable completion of the installation process: a) 1 Phillips Head screwdriver b) Wire Strippers/cutter c) 1 Drill with a 1/2” bit 5. PROCEDURES 5.
100171-03 Water Meter Interface Final Assembly Procedures March 11, 2003 8000171-60-01 Page 3 1) Drill a ½” hole in the center of lid (171401). 2) Insert the 22/3 AWG Wire Assembly (222056) through the ½” Hole in the lid (171401) leaving 3ft of Wire Assembly (222056) with the connector on the inside of the Lid (171401) – see figure 2. 3) Secure Wire Assembly (222056) to the Lid (171401) with the 1.5-5.0 mm PG7 Cord Grip (222059) leaving 3” of the wire (connector end) inside the 171501 Lid Assembly.
100171-03 Water Meter Interface Final Assembly Procedures March 11, 2003 8000171-60-01 Page 4 the Pulse input of the 200171 Circuit Board Assembly. 3) Connect the battery leads to the 2/pin header at reference point BATT of the 200171 Circuit Board Assembly. 4) Check the O-RING Gasket (777000) for seal. 5) Push the 22/3 AWG wire assembly (222056) away from the Circuit Board Assembly (200171) and over the battery assembly (171404) and carefully place the Lid Assembly (171501) on the Base Assembly (171503).
Final Assembly Procedures 100171-xx Water Meter Interface November 25, 2002 Document 8000171-60-00 Appendix Page 5 Figure 1 – 200171-xx Circuit Board Assembly Figure 2 – 171501 Lid Assembly © Copyright 2003, StatSignal Systems, Inc.
Final Assembly Procedures 100171-xx Water Meter Interface November 25, 2002 Document 8000171-60-00 Appendix Page 6 Figure 3 – 171502 Base Assembly I Figure 4 – 171502 Base Assembly II © Copyright 2003, StatSignal Systems, Inc.