00 - S ER IES N ET WO R K SWI T C H ES Install a t i on Ma n ua l Unmanaged AV Rack Network Switches
C E R T I F I C AT I ONS AND WAR NI NGS FCC Warning This device has been tested and found to comply with limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
TABLE OF CONTENTS Certifications and Warnings Table of Contents Figures and Tables 1. Introduction 2. Installation 3. Connecting Network Devices 4. Product Layout 5. Specifications 6. Appendix FCC Warning CE Warning UL About This Manual Pro Tips Notes Cautions Warnings Welcome to Araknis® Networks 1.1 Araknis® 100-Series Overview 1.2 Features 1.3 Package Contents 1.4 Recommended for Installation 2.1 Basic Instructions 2.2 Switch Placement 2.2.1 General Guidelines 2.2.
FIGURES AND TABLES Figures Figure 1. AN-100-SW-R-5 Package Contents Figure 2. AN-100-SW-R-8/16/24 Package Contents Figure 3. Single Switch Network Figure 4. Multiple Switches in Network Figure 5. AN-100-SW-R-5 Rubber Foot Installation Figure 6. AN-100-SW-R-5 On-Wall Mounting Figure 7. AN-100-SW-R-8/16/24 Rubber Foot Installation Figure 8. AN-100-SW-R-8/16/24 Rack Mounting Options Figure 9. AN-100-SW-R-8/16/24 Rack Mounting Procedure Figure 10. AN-100-SW-R-8/16/24 Wall Mounting Option Figure 11.
1 . I N T R O D U C TI ON Welcome to Araknis® Networks Thank you for choosing an Araknis AN-100-SW-R-5, AN-100-SW-R-8, AN-100-SW-R-16, or AN-100-SW-R-24 Unmanaged AV Rack Network Switch. The 100-series unmanaged network switch is an enterprise-class switch specifically designed for use in AV Rack applications.
1 | INTRODUCTION 1.2 — Features Gigabit Ethernet with Auto MDI/MDI-X Detection All ports provide 10/100/1000Mbps line rate speed with auto-negotiation and auto Medium Dependent Interface (MDI)/Medium Dependent Interface Crossover (MDI-X) detection. Auto-negotiation speed automatically selects the best connection speed (10, 100, or 1000Mbps) and duplex mode (half or full duplex) for communication with attached devices.
1 | INTRODUCTION 1.3 — Package Contents Figure 1. AN-100-SW-R-5 Package Contents Screws (4) AN-100-SW-5 Gigabit Ethernet Switch (1) Quick Installation Guide (1) Rack Mount Kit (1) Rubber Feet (1) Wall Anchors (4) DC Power Supply (1) Figure 2. AN-100-SW-R-8/16/24 Package Contents AN-100-SW-R Gigabit Ethernet Switch (1) Quick Installation Guide (1) 1.
2 . I N STA L L ATI ON 2.1 — Basic Instructions These are the basic steps required to install the AN-100-SW-R network switch. During the installation, refer to the listed sections for more detailed information as needed. Do not power the AN-100-SW-R until it is indicated to do so in the instructions. (See Section 2.3, page 15 for power requirements.) 1. Unpack and set or mount the switch in the desired location. See section 2.2 (page 9) for more information. 2.
2 | INSTALLATION Figure 3. Single Switch Network Example - 1 Desktop PC Server Printer/ Scanner AppleTV IP Phone Figure 4. Multiple Switches in Network Example - 2 Desktop PC Server Printer/ Scanner AppleTV IP Phone IP Camera IP Surveillance NVR 9 www.araknisnetworks.com | Support: 866.838.
2 | INSTALLATION 2.2 — Switch Placement This section describes proper placement and mounting for the AN-100-SW-R network switch, including shelf, rack, and on-wall installation. Note: Section 2.2.1 applies to all AN-100-SW-R models. Section 2.2.2 addresses all placement options for the AN-100-SW-R-5 port switch. Section 2.2.3 covers all placement options for the AN-100-SW-R 8/ -16,/ -24 models. 2.2.
2 | INSTALLATION 2.2.2 — AN-100-SW-R-5 Placement Options 2.2.2.1 Shelf Mounting To shelf-mount the network switch, first place the included adhesive feet on the bottom of the unit as shown below. Then, place the switch in the desired position. Make sure the shelf or surface used is flat and stable. Figure 5. AN-100-SW-R-5 Rubber Foot Installation 2.2.2.2 On-Wall Mounting The switch may be mounted on a wall or any other surface by using the included mounting ears.
2 | INSTALLATION 2.2.3 — AN-100-SW-R-8/16/24 Placement Options 2.2.3.1 Shelf Mounting To shelf-mount the network switch, first place the included adhesive feet on the bottom of the unit as shown below. Then place the switch in the desired position. Make sure the shelf or surface used is flat and stable. Caution: Do not stack more than 4 switches together. Do not stack any other equipment on top of the network switch to avoid possible interference or damage. Figure 7.
2 | INSTALLATION Figure 8. (continued) Multiple Mounting Options Standard Protruding Recessed 3. After the ears are attached, mount the switch in the rack as shown below. Insert the bottom screws first to avoid bending the mounting ears or chassis. Figure 9.
2 | INSTALLATION 2.2.3.3 On-Wall Mounting The AN-100-SW-R is designed to be mounted on-wall if desired by using the same parts meant for rack-mounting. This allows for a low-profile installation for the switch, eliminating the need for extra shelving or racks when providing a network switch solution. To wallmount the switch: 4. Locate the included wall-mounting ears and screws from the packaging and a #2 Philips screwdriver. 5. Attach the ears to each side of the switch as shown: Figure 10.
2 | INSTALLATION 2.3 — Powering the AN-100-SW-R Switch 2.3.1 — AC Electrical Requirements 2.3.2 — AN-100-SW-R-5 Table 2. AC Electrical Requirements Input Voltage (AC Only) 100-240V AC, 50~60Hz The AN-100-SW-R-5 is designed with an external DC power supply that connects inline between the power outlet and the DC input on the switch. 2.3.2.1 Power Plug Connection Figure 11. AN-100-SW-R-5 Power Plug Connection 2.3.
3 . C O NNE C TI NG NETWOR K DEV I CES Setup of the AN-100-SW-R is very simple and requires nothing more than connections to other equipment and power. This switch provides automatic crossover detection functionality for any port, so connections can be made to other switches without the need for a crossover cable between devices. 3.
4 . PR O D U C T LAYOUT This section describes the hardware layout of the 100-series unmanaged network switch. Each connection, indicator, and control is summarized. 4.1 — Front Panel Layout Figure 14. Front Panel Layout 2 1 1 Gbps 7 9 11 13 15 8 10 12 14 16 Link/Act 1 3 5 7 9 11 13 15 2 4 6 8 10 12 14 16 Link/Act AN-100-SW-R-16 3 1. Table 4.
4 | PRODUCT LAYOUT 4.2 — Side Layout Figure 15. Side Layout 1 2 1. Ventilation Slots Allows airflow through the chassis to keep the device cool. 2. Rack Mounting Holes The combination of threaded holes at the front and rear of each side allow for many variations in mounting options. 4.3 — Rear Panel Layout Figure 16. Rear Panel Layout 1 1.
5 . S PE C I F I C ATI ONS Table 7. Specifications Model AN-100-SW-R-5 AN-100-SW-R-8 AN-100-SW-R-16 AN-100-SW-R-24 Interface Ports 10/100/1000Base RJ-45 Ports 5 8 16 24 1000Base SFP --- --- --- --- --- --- --- --- PoE ports (In PoE Models) Physical Configuration Flash Memory --- --- 2MB 2MB SDRAM --- --- 64KB (SRAM) 64KB (SRAM) Packet Buffer 128KB 512KB Performance MAC Address Table 4K 8K Switching Capacity 10Gpbs 16Gpbs 32Gpbs 48Gpbs Forwarding Rate 7.4Mpps 11.
6 . APPE ND I X 6.1 — Troubleshooting Use the sections below to troubleshoot issues with the switch. If the problem persists, contact Araknis Networks® Customer Service at (866) 838-5052. 6.1.1 — No Connectivity If one or more attached devices suffer from low or no network connectivity after installation, follow these steps to identify the issue: 1. Reset the switch and router, and then the device(s) with issues. If the problem persists, continue to step 2. 2.
6 | APPENDIX 6.2. — Warranty 2 year 2 Year Limited Warranty Araknis Networks® products have a 2-Year Limited Warranty. This warranty includes parts and labor repairs on all components found to be defective in material or workmanship under normal conditions of use. This warranty shall not apply to products which have been abused, modified or disassembled.
© 2013 Araknis Networks® 131028-1738
