Manual
SM-PROJ-L-BLK
Strong™ Universal Projector Mount for Projectors up to 50 Lbs. (Black)
For Mounting on a Concrete Ceiling (Fig. 4)
a. Pre-drill four holes into concrete using 3/8” Masonry bit.
Insert Concrete Anchors and tap in with hammer, if necessary.
WARNING:WheninstallingCeilingPlateoncinderblock,rstverifythereisaminimumof1-3/8”
of concrete thickness to be used for the Concrete Wall Anchors. Do not drill into mortar joints!
Besuretomountinasolidpartoftheblock,generally1”minimumfromthesideoftheblock.
CinderblockmustmeetASTMC-90specications.Itissuggestedthatastandardelectricdrillonslow
settingisusedtodrilltheholeinsteadofahammerdrilltoavoidbreakingoutthebackofthehole
whenenteringavoidorcavity.Concretemustbe2000psidensityminimum.Lighterdensityconcrete
may not hold concrete anchor.
Make sure that the supporting surface will safely
support the combined load of the equipment and
all attached hardware and components.
b.InsertfourLagScrewsintotheConcreteAnchors
through the Extended Ceiling Plate.
WARNING: Tighten screws so that the Extended
CeilingPlateisrmlyattached,butdonotover-tighten.
Over-tighteningcandamagethescrews,greatly
reducing their holding strength.
c. Insert Extension Pole (ULListedSM-FIXPOLEseries,not
included)intoExtendedCeilingPlate.Lockpolein
place with two M5 set screws.
d.OnbottomofExtensionPole,threadonLow-Prole
Ceiling Plate, making sure the arrow (on bottom)
faces the screen when installed. Tighten Security Screw
(pre-installed)tolockLow-ProleCeilingPlateontoExtension
Pole to set in place.
Step 3: Attach the Projector Mount Body (Fig.5)
a. Slightly loosen all screws so arms easy rotate and extend to
match the holes on the projector. Making sure the arrow
on bottom points toward the projector lens, attach the
Projector Mount Body onto projector using supplied M3,
M4,M5orM6SocketScrewsandM2orM4AllenKey.
b. Depending on the surface of the projector, lowering
theAngleBracketsontheendofthearmstogetaush
mountingmaybenecessary(Fig6).
NOTE:Positioncenterofgravityofprojectortothemiddle
of the mount, if possible.
Step 5: Assemble Projector Mount Body
withLow-ProleCeilingPlate
a. While holding projector, slide top of Projector
MountBodyintotheLow-ProleCeiling
Plateasindicated(Fig.7).
b.UsingeitheraPhilipsHeadScrewdriveror
ngers,pushinandturnlockscrew(attached
toLow-ProleCeilingPlate)tosecure.
c. Using4mmAllenkey,install10-32SocketSecurity
Screwintooppositesideasindicated(Fig.8).
Adjustments
To change the tilt or roll of the mount for centering the picture,
useAllenkeyandrstloosenscrewsonProjectorMountBody.
Tilt the projector into the desired position and re-tighten the screws.
Lifetime
Fig4
Fig5
Fig6
Fig7
Fig8
Lifetime Limited Warranty
All Strong™ products have a Lifetime Limited Warranty. This warranty includes parts and labor repairs on all
components found to be defective in material or workmanship under normal conditions of use. This warranty
shall notapply to products which have been abused, modied or disassembled. Products to be repaired under
this warranty must be returned to SnapAV or a designated service center with prior notication and an
assigned return authorization number (RA).
For Techincal Support : 1.866.838.5052
10-32SecurityScrew
LockScrew