INSTRUCTION MANUAL MODEL: STC-DS4K V.
**IMPORTANT NOTE** To ensure the product is being utilized to its full potential, we recommend checking our website for new product updates. If your unit is having trouble, please check the website to determine you are using the latest firmware or software version. TECHNICAL SUPPORT EMAIL: Stealthcam@gsmorg.com Please allow 48 hours for email response. STEALTHCAM LLC P.O. Box 535189 Grand Prairie, TX 75053-‐9504 www.
TABLE OF CONTENTS Camera Overview General Information Camera Programming Quick Set 1 (Q1) Quick Set 2 (Q2) Quick Set 3 (Q3) Custom Settings Test Mode Memory Card Installation Formatting Battery Removal & Installation View and Deleting files Definitions Frequently Asked Questions (FAQs) FCC Compliance Limited Warranty Information www.stealthcam.
CAMERA OVERVIEW Front Open Front Close Bottom www.stealthcam.
CAMERA OVERVIEW (CONT) Side Back Battery Compartment www.stealthcam.
GENERAL INFORMATION Storing conditions ! Operating Environment: 14 to 104 deg F (-‐10 to 40 deg C). 20-‐85% relative humidity, non-‐condensing. Special care instructions!! ! ! ! ! ! ! ! ! ! ! The camera is designed to be weather resistant. Never attempt to immerse the unit in water or any other liquid. This will damage the unit and void the warranty. Do not mix old and new batteries.
CAMERA PROGRAMMING This DS4K features six distinct modes of operation: OFF / Q1 / Q2 /Q3 / CUSTOM / TEST. Each setting is activated based upon the position of the switch on the inside of the unit. OFF – This position completely powers down the unit. Q1 – This is the first Quick Set programming mode.
CAMERA PROGRAMMING – CUSTOM (CONT) CUSTOM – This is the fifth setting and is defined by the user. When the camera is changed to this mode, the display screen will reflect the last program setting: Number of images on the memory card, Countdown timer and Battery percentage. PHOTO 00000 00:30 100% The Day default programming is set to 8.0MP, 5-second timeout delay and 1 Photo Burst; the Night default programming is set to 6.
CAMERA PROGRAMMING – CUSTOM (CONT) ! SETUP DATE – 01/01/177 (default): This setting is used to give the camera the correct date to use on the Info Bar of the images. The format is in a MM/DD/YY setup. With the MM (month) setting blinking, use the UP and DOWN arrows to be change the setting from 1 to 12.
CAMERA PROGRAMMING -‐ CUSTOM (CONT) ! TIME FORMAT – 12 HOUR (default): This setting is used to tell camera if the time programmed and displayed on the Info Bar should be in the basic 12 hour (AM/PM) format or the 24 hour (military) format. With this option blinking, pressing the UP or DOWN arrow buttons will cause the camera to cycle between the two options.
CAMERA PROGRAMMING -‐ CUSTOM (CONT) o PIR PHOTO (default): In this mode the camera will take a designated amount of picture with a designated time out when the camera senses activity in front of the unit. This mode adjusts for both day and night activities. " " " " " PHOTO DAY PHOTO RES – 16.0 (default): This setting is used to determine the Megapixel resolution of each image taken by the camera.
CAMERA PROGRAMMING - CUSTOM (CONT) " " REDUCE BLUR – ADVANCED (default): This setting is used to determine if the camera should use the MATRIX Blur reduction technology to dramatically reduce the blur effect resulting in clearer night time infrared shots. (STANDARD) Minimizes blurring effect in images while retaining long---range night image capability. (ADVANCED) Maximum blur reduction achieved through a faster shutter speed.
CAMERA PROGRAMMING -‐ CUSTOM (CONT) o PIR VIDEO: In this mode the camera will take a video clip at a designated resolution for a designated length with a designated time out when the camera senses activity in front of the unit. This mode is available for both day and night activities.
CAMERA PROGRAMMING -‐ CUSTOM (CONT) o PIR COMBO: In this mode the camera will take a video and photos simultaneously. The video clip is at a designated resolution for the designated length with a designated time out when the camera senses activity in front of the unit. While taking a the video the camera will begin saving frames as images with the same resolution as the video starting with the first frame and an additional frame every 5 seconds of video record.
CAMERA PROGRAMMING -‐ CUSTOM (CONT) o TIME LAPSE (TL): In this mode the camera will take a designated amount of pictures with a designated time out between the designated hours of operation even if there is no activity in front of the camera. " " " " " DAY PHOTO RES – 8.0 (default): This setting is used to determine the Megapixel resolution of each image taken by the camera.
CAMERA PROGRAMMING -‐ CUSTOM (CONT) Using the UP and DOWN arrows will allow the setting to be change from 00 to 59. Again when this setting is on the appropriate minute, press the RIGHT arrow key to move to the AP (am/pm) setting and it will start to blink. Using the UP and DOWN arrows will allow the setting to be changed from AM to PM.
CAMERA PROGRAMMING -‐ CUSTOM (CONT) ! CAMERA NAME – STEALTH CAM (default): This setting is used to identify the camera on the Info Bar. It can be up to 13 characters long in the form of alpha (A-Z), numeric (0- 9), or spaces. With this option blinking, use the UP or DOWN arrow buttons to change the initial character.
CAMERA PROGRAMMING -‐ CUSTOM (CONT) ! LATITUDE – 000.000000N (default): This setting is used for the GEO-TAG of the camera. It will not be displayed on the images directly, but rather on the background image information. The coordinates can be changed from 000.000000 to 179.999999 and either N (North) or S (South).
CAMERA PROGRAMMING -‐ CUSTOM (CONT) o SECURITY KEY – 0000 (default): To change the key to an owner operated one press the ENTER button. With this option blinking, use the UP or DOWN arrow buttons change the first digit to the preferred number or letter. Then using the LEFT button, move to the second digit and change it to the preferred number or letter as well.
CAMERA PROGRAMMING TEST – This is the final switch setting, and is used to test the camera’s PIR sensor coverage area. When moved to this setting the display will display: TEST VXX.XX.XX The number listed at the bottom of the display shows the current version of the firmware that is installed on the camera. The first two XX indicates which model version you have and the last four XX.
MEMORY CARD INSTALLATION To insert the SD memory card into the camera: first locate the SD card slot on the right hand side of the of the camera case. Next with the SD card label facing towards the front of the camera, insert the SD card. When the card has been pressed in fully there will be a noticeable resistance as the spring locking mechanism activates to hold on the SD card.
MEMORY CARD (CONT) FORMATTING SD CARD It always best to format your SD cards from the actual device your using, in this case the camera. This will allow the camera to format the card in the proper fashion. 1. 2. 3. 4. 5. 6. 7. First insert your SD memory card into the camera. Slide the switch to the Custom setting. Press the Menu. Press the Up Arrow once.
BATTERY REMOVAL & INSTALLATION To remove the batteries from the unit; open the case and press the EJECT button on the lower right hand corner. This will cause the battery tray to be released and slide downwards. New, Alkaline or Lithium, ‘AA’ batteries must be inserted with the orientation as shown on the tray.
VIEW & DELETING IMAGES The camera allows for two (2) ways to view your images. First is the direct connection for the camera to the computer via a USB cable (not included). This is a USB mini to standard USB (type A/B) cable.
DEFINITIONS MATRIX (Blur Reduction Technology) – Advanced blur reduction dramatically reduces blur effects resulting in sharper, clearer images. RETINA (Sub 1-‐Second Trigger) – Superior low light performance for extended nighttime range. MULTI-‐ZONE DETECTION -‐ Provides for more accurate coverage at angle & distance, maximizing the cameras triggering capability.
FREQUENTLY ASKED QUESTIONS Q: Can I mix batteries together? A: NO, you should never mix old with new OR Alkaline with Lithium with Rechargeable. Q: Is my game camera Mac compatible? A: Yes, This camera model works with 10.6 and above. Q: Can I use rechargeable batteries in the camera? A: Rechargeable batteries are fine for the unit; regular alkaline batteries designed for digital electronics are recommended for best performance.
FREQUENTLY ASKED QUESTIONS (CONT) Q: Can I use my game camera through a window or glass door? A: Glass may disrupt your sensor beam we don’t advise using the camera in this fashion.
FCC COMPLIANCE GSM STC-DS4K NOTE: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
LIMITED WARRANTY INFORMATION Your Stealth Cam scouting camera is covered by a 365 Day Limited Warranty on parts and labor from the date of original purchase, and purchases must be made through an authorized dealer. The warranty covers defects in workmanship and materials. The warranty does not apply to units, which have been damaged or abused intentionally or unintentionally.
MANUEL D'INSTRUCTIONS MODÈLE : STC-DS4K V.01 www.stealthcam.
**NOTE IMPORTANTE** Pour vous assurer que le produit soit utilisé à son plein potentiel, nous vous recommandons de vérifier notre site Web pour obtenir les nouvelles mises à jour du produit. Si votre appareil a des problèmes, veuillez consulter le site pour déterminer si vous utilisez le dernier micrologiciel ou la toute dernière version du logiciel. SOUTIEN TECHNIQUE COURRIEL : stealthcam@gsmorg.
TABLE DES MATIÈRES Aperçu de l'appareil photo Renseignements généraux Réglage de l'appareil photo Réglage rapide 1 (Q1) Réglage rapide 2 (Q2) Réglage rapide 3 (Q3) Paramètres personnalisés Mode Test Carte mémoire 33-34 35 Installation Formatage Installation et retrait de la pile Affichage et Suppression des fichiers Définitions Foire aux questions (FAQ) Conformité FCC Renseignements sur la garantie limitée 50 5
APERÇU DE L'APPAREIL PHOTO Devant ouvert Devan t Bas www.stealthcam.
APERÇU DE L'APPAREIL PHOTO (SUITE) Arrière Côté www.stealthcam.
RENSEIGNEMENTS GÉNÉRAUX Conditions de rangement ! Environnement d'exploitation : -‐10 à 40 deg C (14 à 104 deg F). 20 -‐ 85 % humidité relative, sans condensation. Instructions pour les soins spéciaux ! L'appareil photo est conçu pour résister à l'eau. N'essayez jamais de plonger l'appareil dans l'eau ou dans tout autre liquide. Ce qui pourrait endommager l'appareil et annuler la garantie.
RÉGLAGE DE L'APPAREIL PHOTO Ce DS4K comprend 6 modes distincts d'opération : Arrêt/Q1/Q2/Q3/Personnalisé/Test. Chaque paramètre est activé en fonction de la position de l'interrupteur à l'intérieur de l'appareil. Arrêt – Cette position coupe complètement l'alimentation de l'appareil. Q1 – Il s'agit du premier mode de programmation de Réglage rapide (Quick Set).
RÉGLAGE DE L'APPAREIL PHOTO -‐ PERSONNALISÉ (SUITE) Personnalisé – Il s'agit du cinquième paramètre et est défini par l'utilisateur. Lorsque l'appareil est changé pour ce mode, l'écran d'affichage reflètera le dernier réglage du programme : Nombre d'images contenues sur la carte mémoire, la minuterie et le pourcentage de la pile. PHOTO 00000 00:30 100 % Le réglage par défaut du journèe est réglé à 8.
RÉGLAGE DE L'APPAREIL PHOTO -‐ PERSONNALISÉ (SUITE) ! RÉGLAGE DE LA DATE – 01/01/17 (par défaut): Ce paramètre est utilisé pour indiquer la bonne date à la caméra à utiliser sur la Barre d'infos des images. Le format est MM/JJ/AAAA.Lorsque le MM (mois) clignote, utilisez les flèches vers le HAUT et vers le BAS pour passer de 1 à 12.
RÉGLAGE DE L'APPAREIL PHOTO -‐ PERSONNALISÉ (SUITE) ! FORMAT DE L'HEURE – 12 HEURES (par défaut): Ce paramètre est utilisé pour indiquer à l'appareil photo si l'heure programmée et affichée sur la Barre d'infos doit être au format de base de 12 heures (AM/PM) ou au format 24 heures (militaire). Lorsque cette option clignote, appuyer sur les flèches HAUT ou BAS pour basculer entre les deux options.
RÉGLAGE DE L'APPAREIL PHOTO -‐ PERSONNALISÉ (SUITE) o PHOTO PIR (par défaut): Dans ce mode, l'appareil photo prend une quantité désignée de photos dans un laps de temps établi lorsque l'appareil photo détecte une activité se déroulant devant l'appareil. Ce mode est disponible à la fois pour les activités de jour et de nuit. " DAY PHOTO RES - 16.
CAMERA PROGRAMMING -‐ CUSTOM (CONT) Contrôle de luminosité IR - FULL (par défaut): Ce réglage est utilisé pour régler la luminosité des voyants IR. Avec cette option Clignote, utilisez la flèche HAUT ou BAS pour passer de la luminosité FULL à la luminosité HALF. Sur la pleine luminosité Les LED ont une gamme de flash supplémentaire le rendant idéal pour de grandes zones ouvertes. La luminosité HALF est idéale pour les plans rapprochés empêchant le sujet d'être surexposé.
RÉGLAGE DE L'APPAREIL PHOTO -‐ PERSONNALISÉ (SUITE) o COMBO PIR: Dans ce mode, la caméra prend simultanément une vidéo et des photos. Le clip vidéo est à une résolution désignée pour la longueur désignée avec un temps de temporisation désigné lorsque la caméra détecte l'activité devant l'unité.
RÉGLAGE DE L'APPAREIL PHOTO -‐ PERSONNALISÉ (SUITE) o VIDÉO PIR: Dans ce mode, l'appareil photo prendre un clip vidéo à une résolution désignée pour une durée établie avec une temporisation spécifiées lorsque l'appareil photo détecte une activité se déroulant devant l'appareil. Ce mode est disponible à la fois pour les activités de jour et de nuit.
RÉGLAGE DE L'APPAREIL PHOTO -‐ PERSONNALISÉ (SUITE) o LAPSE DE TEMPS (Délai): Dans ce mode, l'appareil photo prend une quantité désignée de photos dans un délai établi entre les heures d'opération désignée même s'il n'y a aucune activité devant l'appareil photo. " " " " " DAY PHOTO RES - 8.0 (par défaut): Ce paramètre permet de déterminer la résolution de chaque image en mégapixels Prise par la caméra.
RÉGLAGE DE L'APPAREIL PHOTO -‐ PERSONNALISÉ (SUITE) DÉBUT DU DÉLAI (TL) – 06:00 PM (par défaut): Ce paramètre est utilisé pour donner à l'appareil photo le temps de démarrage pour commencer le délai de la photographie. Le format par défaut est HH/MM/AP, si le format de l'heure doit être celui de 24 heures sera HH/MM. Lorsque le paramètre HH (heure) clignote, utilisez les flèches vers le HAUT et vers les BAS pour permettre au paramètre de changer de 1 à 12.
RÉGLAGE DE L'APPAREIL PHOTO -‐ PERSONNALISÉ (SUITE) ! NOM DE L'APPAREIL PHOTO – STEALTH CAM (par défaut): Ce paramètre est utilisé pour identifier l'appareil photo sur la Barre d'infos. Il peut compter jusqu'à 13 caractères sous forme alpha (A - Z), numérique (0 - 9), ou comporter des espaces. Lorsque cette option clignote, utilisez les flèches HAUT ou BAS pour changer le nombre initial de caractères.
RÉGLAGE DE L'APPAREIL PHOTO - PERSONNALISÉ (SUITE) ! LATITUDE – 000.000000N (par défaut): Ce paramètre est utilisé pour le GEO-TAG de l'appareil photo. Il ne sera pas affiché sur les images directement, mais plutôt sur les renseignements de l'image de fond. Les coordonnées peuvent être changées de 000.000000 à 179.
RÉGLAGE DE L'APPAREIL PHOTO -‐ PERSONNALISÉ (SUITE) o CLÉ DE SÉCURITÉ – 0000 (par défaut): Pour modifier la clé d'un propriétaire utilisée, appuyez une fois sur le bouton Entrée. Lorsque cette option clignote, utilisez la flèche vers le HAUT ou vers le BAS pour changer le premier chiffre par un nombre ou une lettre désiré.
RÉGLAGE DE L'APPAREIL PHOTO ! LANGUE 4 l'anglais (par défaut): Cette nouvelle fonctionnalité vous permet de sélectionner la langue que vous préférez utiliser dans le menu . En appuyant sur la touche ENTER vous serez en mesure de faire défiler les options suivantes: Anglais / Allemand / Français / Espagnol. Une fois sélectionné, appuyez sur la touche ENTRER de nouveau pour enregistrer votre réglage.
CARTE MÉMOIRE INSTALLATION Pour insérer la carte mémoire SD dans l'appareil: localisez la fente de la carte SD sur le côté droit du boîtier de l'appareil photo. Ensuite, avec l'étiquette de la carte SD orientée vers l'avant de l'appareil photo, insérez la carte SD.
FOMATAGE DE LA CARTE SD Il est toujours mieux de formater vos cartes SD à partir de l'appareil actuel que vous utilisez, dans ce cas l'appareil photo. Ce qui permettra à l'appareil photo de formater la carte dans le mode approprié. 1. 2. 3. 4. Insérez d'abord votre carte mémoire SD dans la caméra. Glissez l'interrupteur au paramètre Personnalisé. Appuyez sur Menu. Appuyez une fois sur la flèche vers le haut (Up).
INSTALLATION ET RETRAIT DE LA PILE Pour retirer les piles de l'appareil, ouvrez le boîtier et appuyez sur le bouton ÉJECTION situé dans le coin inférieur droit. Ce qui permettra de glisser et de retirer le Compartiment à piles. De nouvelles piles, alcalines ou au lithium, de type 'AA' doivent être insérées en respectant l'orientation indiquée sur le compartiment.
AFFICHAGE ET SUPPRESSION DES FICHLIERS La caméra offre deux (2) façons de voir vos images. La première est la connexion directe de l'appareil photo à l'ordinateur via un câble USB (non fourni). Il s'agit d'un mini câble USB vers un câble USB standard (type A/B).
DÉFINITIONS REFLEX (Sensibilité avancée à faible luminosité) -‐ Vitesse de déclenchement ultra-‐rapide, en moyenne < 1 seconde avec des temps de récupération programmables aussi bas que 5 secondes. MATRIX(Technologie de réduction du flou) – La réduction avancée du flou réduit de manière importante les effets du flou, résultant en des images plus claires et plus nettes.
FOIRE AUX QUESTIONS Q : Mon appareil de jeu pour Mac est-‐i compatible? R : Oui, ce modèle d'appareil photo fonctionne avec la version 10.6 et plus. Q : Puis-‐je utiliser des piles rechargeables dans l'appareil photo? R : Les piles rechargeables sont très bien pour l'appareil; les piles alcalines ordinaires conçues pour les appareils électroniques numériques sont recommandées pour obtenir une meilleure performance.
FOIRE AUX QUESTIONS (SUITE) Q : Puis-‐je utiliser mon appareil de jeu par une fenêtre ou une porte de verre? R : Le verre peut perturber le faisceau de votre détecteur; nous ne vous conseillons pas d'utiliser l'appareil photo dans ce mode.
CONFORMITÉ FCC GSM STC-DS4K Remarque : Cet équipement a été testé et se conforme aux exigences des appareils numériques de classe B, conformément à la partie 15 des Règles FCC. Ces limites sont conçues pour fournir une protection raisonnable contre les interférences nuisibles présentes dans une installation résidentielle.
RENSEIGNEMENTS SUR LA GARANTIE LIMITÉE Votre appareil photo d'exploration Stealth Cam est couverte par une garantie limitée de 365 jours sur les pièces et la main-‐d'œuvre à partir de la date d'achat initial, et les achats doivent être effectués auprès d'un revendeur autorisé. La garantie couvre les défauts de fabrication et les matériaux.