STC-WD2-IR User’s Manual Toll Free Customer Support 1-877-269-8490 www.stealthcam.net Version 1.
STC-WD2-IR For Customer Service or Warranty Information Call Toll Free 877-269-8490 Stealth Cam, LLC P.O. Box 535189 Grand Prairie, Texas 75053-5189 www.stealthcam.net Stealth Cam Limited Warranty Your Stealth Cam is covered by a One Year Limited Warranty on parts & labor from the date of purchase. The warranty covers defects in workmanship & materials. The warranty does not apply to units, which have been damaged or abused intentionally or unintentionally.
STC-WD2-IR Manual Contents Camera overview 4 Camera kit contents 8 Battery and memory Installation 9 Set up and programming 12 Camera use 20 Mounting the camera 21 Viewing & Deleting images 27 Memory compatibility chart 36 Technical Specs 37 General Information 40 www.stealthcam.
STC-WD2-IR Camera overview Front housing image with major parts indication. www.stealthcam.
STC-WD2-IR Open view image with major parts indication www.stealthcam.
STC-WD2-IR Side view with major parts indication For use with Stealth Cam exclusive Monitor/TV (sold separately) www.stealthcam.
STC-WD2-IR Image Capacity Chart SD card High Low Base AVI 16MB 52 80 160 16 32MB 104 160 320 32 64MB 208 320 640 64 128MB 416 640 1280 128 256MB 832 1280 2560 256 512MB 1664 2560 5120 512 1GB* 3328 5120 10240 1024 2GB* 6656 10240 20480 2048 * Subject to card compatibility under different brand NOTE: Picture / Image Capacity Chart provides approximate number of images or AVI movies based on resolution setting and the size of memory card.
STC-WD2-IR Camera kit contents • Model STC-WD2-IR Digital Security/Scouting Camera • CDROM (Contains Ulead Photo Express 8 and camera driver) • User Manual. • USB cable. • TV out cable for TV (RCA Jack). • TV out cable for handheld TV (Mini Jack). • Strap. www.stealthcam.
STC-WD2-IR Battery & memory installation Warning: Do not use different Voltage lead acid battery other than the one specified in this section. Doing so will damage the camera and will void the warranty. The Stealth Cam STC-WD2-IR Advanced Digital Security/Scouting Camera is designed to operate using two different types of battery power options. NOTE: Always have camera in OFF position when installing or removing batteries. Batteries “C” cell The internal battery compartment accepts 6 “C” cell batteries.
STC-WD2-IR 12V Lead Acid external battery The STC-WD2-IR is equipped with an external power jack designed to accept a barrel plug cable to attach to a sealed lead acid battery. (Sold separately). Battery cable and complete 12V Lead Acid battery kits are available wherever Stealth Cam scouting cameras are sold or call toll free 877-269-8490. Only Stealth Cam external battery accessories are recommended. • Make sure the camera power switch is OFF and power source switch on BATTERY.
STC-WD2-IR Memory Options Your STC-WD2-IR camera is equipped with 16MB built in flash memory. The camera is also equipped with an expendable media card slot capable accepting up to 2GB SD card (sold separately). With no memory card inserted into the slot, the camera will use the built in 16MB memory. If a SD card is inserted into the slot then the camera will bypass the built in memory and utilize the SD memory.
STC-WD2-IR out the card gently. SD cards must be clean (no images from other sources), if you are using the SD card from other cameras, please make sure to format the SD card prior use in the STC-WD2IR (See format section on page 18). New cards are good to use straight from the package. Set up and Programming When the camera is first turned on the internal LCD screen displays the camera status. The following information is present on this screen.
STC-WD2-IR Definition • Time out: To set the amount of time in minutes the camera will sleep between PIR triggering. • Infrared LED: In low light conditions the infrared emitter will automatically activate. • Capture mode: The capture mode that you have selected. • o 1P: Single image capturing per PIR triggering. o 2P: Two images continuous capturing per PIR triggering. o 3P: Three images continuous capturing per PIR triggering. o Video: Taking 10 seconds video per PIR triggering.
STC-WD2-IR pixels image. (Low image quality) o Video resolution (320 x 240): This is the resolution during video capturing. • Batteries Status: It shows the battery status. o Full: It shows the batteries are full. o Half: It shows the batteries are half. o Low: It shows the batteries are low and front low battery indicator will also be lit. Blinking When the camera has detected low batteries, (Batteries are lower then 6.6 +/-0.2Volts) the camera unit will power off within 30 seconds automatically.
STC-WD2-IR Programming the Stealth Cam STC-WD2-IR Switch the camera to the ON position. LCD screen will show “ON” for few seconds and then display the camera status screen. Press the MENU button within 30 seconds to enter programming mode. This will bring up the SETTING screen. If MENU button is not pressed within 30 seconds, camera will automatically enter PIR detection mode. Set the Resolution: The first program setting is resolution.
STC-WD2-IR Set the Capturing sequence. The Stealth Cam STC-WD2-IR can be programmed to shoot 1-3 pictures per triggering or 10 seconds of video. • This icon will be blinking • Press [OK] button to choose the selection • Press the [UP] or [DN] button to select the desired capture setting (number of pictures per triggering). 1picture / 2 pictures / 3 pictures • or Video Press [OK] to save and exit to TIME OUT setting.
STC-WD2-IR Set Date and Time: This camera uses the 24hr military time format. • The word TIME and minute digit will be blinking.
STC-WD2-IR (01 – 31) • Press [OK] to confirm the date setting and enter year setting {YY (Year) will be blinking} • Press [UP] or [DN] to increase or decrease the year value. (04 – 99) • Press [OK] to confirm the year setting and exit to delete setting. Delete / Format setting • The word FORMAT will be blinking. • Press [OK] to choose the selection • Press [OK] the second time to format the memory (if SD memory card is inside the card slot, it will format the SD memory card.
STC-WD2-IR • Press [OK] to confirm and exit to RESOLUTION setting • If you choose Delete One or Delete All, you will remain in this mode until you press [DN] button to move the selection to No Delete then press [OK] to exit to Resolution setting. • Press [MENU] to exit to power on status. Once all settings have been completed press the [MENU] button to return to CAMERA STATUS screen.
STC-WD2-IR Using the camera Once all program setting has been completed your Stealth Cam is ready for field use. Getting started Mounting the Camera. It is recommended to mount the camera 4-5 ft off the ground with the camera pointed at a slight downward angle. Be sure to avoid mounting the camera facing east or west as the rising and setting of the sun could produce false triggers and overexposed images.
STC-WD2-IR Mounting the camera Mounting the camera with Tree Screw (Optional Accessory sold separately) • Hand twist the screw into the tree or post at the desired position. • Attached the camera to the screw by turning the camera onto the mounting screw to the desired position. • Tighten the stabilizer nut. www.stealthcam.
STC-WD2-IR Attached camera to tree screw. Do not over tighten as this may cause damage to camera housing. Using the supplied nut and washer, tighten to the bottom of camera for greater stability. Mounting the camera with the supplied strap • Insert the strap through the strap slots on the rear housing. • Wrap the strap around the mounting surface. Secure the strap and tighten the buckle in order to secure the camera. www.stealthcam.
STC-WD2-IR Stealth Cam offers a Security Lock Bracket for uses exclusively with this camera. See included accessory card or call toll free 877-269-8490. In order to obtain proper weather resistance, please make sure that both door latches are securely locked in place. Testing the camera coverage area One of STC-WD2-IR Cam’s many features is the ability to test the coverage area. • After mounting the camera, open front housing and slide the power to ON. • After the font LCD screen has powered on.
STC-WD2-IR mounted camera in the proper position. A green indicator light on the front will blink on when you have intruded the coverage area. • Adjust the camera position as needed and repeat testing until the desired coverage area is achieved. • When you have completed the testing the coverage area there are 2 methods for exiting the test mode: a. Open the front housing and press the [TEST] button to exit test mode.
STC-WD2-IR Using the camera in PIR detection mode • Mount the camera to tree or other sturdy object using either supplied tree screw or mounting strap (Please refer to the mounting suggestions section in this manual) • Open the front housing and move the switch to the ON position. At this point you have 30 seconds to make any program adjustments. • After 30 seconds the camera’s green test light will begin blinking and enter count down mode.
STC-WD2-IR The IR LED will only activate in low light conditions. When using the AVI function, Time/Date stamp will not appear on the AVI video clips. www.stealthcam.
STC-WD2-IR Viewing and deleting the images The STC-WD2-IR cam offers the user three different options for viewing the images. The external LCD display screen on the front housing will show the number of images in memory. To wake the camera from PIR detection mode press and hold either the [UP] or [DN] button for about 5 seconds. The instructions below are based on starting from a camera that is turned off.
STC-WD2-IR • Press [OK] button to choose the setting. • Press [UP] or [DN] to select TV system. TV-N (TV out in NTSC System). TV-P (TV out in PAL System) • Press [OK] to confirm setting. • Press [MENU] to exist to power on status to continue with your image viewing. • Using the [UP] and [DN] buttons select the image you wish to view. • Press [OK] button to bring up the whole image on the screen. • You may use the [UP] and [DN] buttons at this point to navigate though all the images in memory.
STC-WD2-IR Viewing the images on your home TV equipped with an RCA input jack (cable included) • Attach the appropriate cable to the video out jack on the camera. Insert the other end into the RCA video in jack on the TV. Turn on both the camera and TV. Make sure to switch to VIDEO IN mode on your TV. (See your TV owner’s manual for directions. • Attach the appropriate cable to the video out jack on the camera. Insert the other end into the video in jack on handheld LCD TV monitor.
STC-WD2-IR • Press [OK] to confirm setting. • Press [MENU] to exist to power on status to continue with your image viewing. • Using the [UP] and [DN] buttons select the image you wish to view. • Press [OK] button to bring up the whole image on the screen. • You may use the [UP] and [DN] buttons at this point to navigate though all the images in memory. • To return to the thumbnail view from the full size image press the [OK] button.
STC-WD2-IR like to see. • Press the [OK] button to play back the AVI motion clip. • To return to thumbnail image selection view, press [OK] button at the end of the AVI clip. Viewing images by computer download The Stealth Cam STC-WD2-IR Digital Scouting Camera is a plug and play USB storage device. This means users of Windows 2000 / ME / and XP operating system need not install the camera driver. This camera is not MAC compatible.
STC-WD2-IR Attention: The software CD-ROM packaged with the camera is designed for PC’s only (not MAC compatible). Playing this CD-ROM on a stereo or CD player may cause damage to it. Software installation • Unplug the USB cable from PC. • Insert the CDROM in CD driver of your PC. • The auto-run program will execute. • Follow the instructions shown on screen from your PC to completely install the driver and application program. • Restart windows.
STC-WD2-IR NOTE: Users of Windows 98 or earlier must install camera driver prior to connecting the USB cable. LOW BAT TE ST • If your computer doesn’t run automatically, please click “Start” button and choose “Run”, and then browse the CD drive and click “Setup”. • Operation manual of Ulead Photo Explorer is contained on the provided CDROM. www.stealthcam.
STC-WD2-IR Viewing the images on your computer using the provided software Please refer to Installation section on above to install the software and application program properly. • Slide the power switch to OFF location. • To view the images simply plug one end of the USB cable into an available USB port on your computer. • Plug the other end of USB cable into the camera. The camera will automatically power ON and display a USB icon on the LCD screen.
STC-WD2-IR • While viewing images either in thumbnail view or full screen press [MENU] once and press [DN] button to enter the DELETE & FORMAT menu. • Press [OK] button to confirm setting • Using the [UP] and [DN] buttons to the desired function. No Delete (NO-dL), Delete one (d-ONE), or Delete ALL (d-ALL). • If you chose to delete one picture, it will delete the picture that you selected on the Thumbnail view or the image that is on full screen.
STC-WD2-IR SD Memory Card Compatibility Chart The following cards have been tested and approved for use in the STC-WD2-IR model.
STC-WD2-IR Technical Specifications System Requirements and Compatibility • Windows 98/98se/2000/Me/XP • Pentium 450MHz or equivalent processor • 128MB SDRAM or above • VGA Video Card with 32MB RAM for minimum, Color 16 bit or higher • An available CDROM driver and an available USB Port • 600 MB free hard disc space • Optional: Windows compatible sound card, Microphone and speaker If you have any questions regarding your PC specifications please call your PC manufacturer. www.stealthcam.
STC-WD2-IR Camera Features and Specification. • Image sensor: 1.3 mega-pixels (2.0 mega-pixels interpolation) • Built in 1.8” B&W LCD display • Built in 16M flash memories for image storage • External memory support: SD memory card up to 2.0GB • Resolution Options: Hi (2.0M), Base (1.2M), VGA (0.
STC-WD2-IR • Battery low indicator • Green Test LED indicator • TV out support for NTSC and PAL system • Focusing: 5 ft to Infinity • High precision 4 P glass lens with coating. • Effective viewing Angle: 52 deg. • PIR detection angle 48 deg. • Low power consumption: Standby current: < 1mA. Capture current <150mA • Interface type: USB 1.0 • Power: C size alkaline Batteries x 6 • External power: 12 volts battery pack • Image format: Standard JEPG. And Motion JEPG (AVI) www.stealthcam.
STC-WD2-IR General Information Storing conditions • Operating Environment: 14 to 104 deg F (-10 to 40 deg C). 2085% relative humidity, non-condensing. Special care instructions!! • The camera is designed to be weather resistant. Never attempt to immerse the unit to water or any other liquid. This will damage the unit and void the warranty. • Use a soft lens cloth for cleaning lens. Avoid touching lens with fingers. • Remove dirt or stains with a soft cloth dampened with water or neutral detergent.
STC-WD2-IR • Do not mix new and old batteries. • Do not open the camera for unauthorized service. This could cause serious damage to the unit and will void the warranty. This camera is a precision electronic device. Do not attempt to service this camera yourself, as opening or removing covers may expose you to dangerous voltage points or other risks. WF031E_R1 Print In China www.stealthcam.