Stealth Cam STC-WD3 User’s Manual Toll Free Customer Support 1-877-269-8490 www.stealthcam.
STC-WD3 For Customer Service or Warranty Information Call Toll Free 877-269-8490 Stealth Cam, LLC P.O. Box 211662 Bedford, Texas 76095 www.steatlhcam.net Stealth Cam Limited Warranty Your Stealth Cam is covered by a One Year Limited Warranty on parts & labor from the date of purchase. The warranty covers defects in workmanship & materials. The warranty does not apply to units, which have been damaged or abused intentionally or unintentionally. Tampering with or altering the unit will void the warranty.
STC-WD3 Manual Contents Warranty 2 Camera overview 4 Camera kit contents 8 Battery and memory Installation 9 Set up and programming 13 Using the camera 22 Viewing & Deleting images 32 Using Solar Panel 40 CF Memory Card Compatibility Chart 42 Technical Specs 43 General Information 46 www.stealthcam.
STC-WD3 Camera overview Front housing image with major parts indication. For use with Stealth Cam cable only. (sold separately) www.stealthcam.
STC-WD3 Open view image with major parts indication www.stealthcam.
STC-WD3 Side view with major parts indication For use with Stealth Cam exclusive Monitor / TV sold separately www.stealthcam.
STC-WD3 Picture / Image Capacity CF card High 3.0M Med 2.0M Low 1.3M Base 0.3M AVI (10 sec) 16MB 20 26 40 80 8 32MB 40 52 80 160 16 64MB 80 104 160 320 32 128MB 160 208 320 640 64 256MB 320 416 640 1280 128 512MB 640 832 1280 2560 256 1G 1280 1664 2560 5120 512 2G 2560 3328 5120 10240 1024 NOTE: Picture / Image Capacity Chart provides approximate number of images or AVI movies based on resolution setting and the size of memory card.
STC-WD3 Camera kit contents • Model STC-WD3 Digital Scouting Camera • CDROM (Contains Ulead Photo Express 8 and camera driver) • User Manual. • 1.5M USB cable. • 1.5M TV out cable for TV (RCA Jack). • 1.5M TV out cable for handheld TV (Mini Jack). • Strap. • Tree screw with nut. • Washer x 2. www.stealthcam.
STC-WD3 Battery & memory installation. The Stealth Cam STC-WD3 Advanced Digital Scouting Camera is designed to operate using two different types of battery power options. NOTE: Always have camera in OFF position when installing or removing batteries. Batteries “C” cell The internal battery compartment accepts 6 “C” cell batteries. Be sure to use high quality brand name alkaline batteries. Install batteries in correct polarity (+/-) as noted inside battery compartment. www.stealthcam.
STC-WD3 12V Lead Acid external battery. The STC-WD3 is equipped with an external power jack designed to accept a barrel plug cable to attach to a sealed lead acid battery. (sold separately). Battery cable and complete 12V Lead Acid battery kits are available wherever Stealth Cam scouting cameras are sold or call toll free 877-269-8490. Only Stealth Cam external battery accessories are recommended. • Make sure the camera power switch is OFF and power source switch on BATTERY.
STC-WD3 Please make sure the voltage and polarity (+/-) are correct before connection. Incorrect voltage or polarity (+/-) will damage the camera. Memory Options. Your STC-WD3 camera is equipped with 32MB built in flash memory, the camera is also equipped with an expendable media card slot capable accepting up to 2GB Compact Flash card (sold separately), With no memory card inserted into the slot, the camera will use the built in 32MB memory.
STC-WD3 Inserting CF card. Make sure camera is in the OFF position when ever adding or removing memory. • Insert CF memory card in to the CF card slot completely and in the correct direction as shown by the sticker located at the top of the housing. • To remove the CF memory card by press the eject button which is on the upper of the card.
STC-WD3 Set up and Programming. When the camera is first turned on the internal LCD screen displays the camera status. The following information is present on this screen. If no buttons are pressed after 30 seconds the LCD screen will power down to conserve battery life. To re-power the screen press and hold the UP or DOWN button for at least 5 seconds. www.stealthcam.
• STC-WD3 Time out: To set the amount of time in minutes the camera will sleep between PIR triggering. • Auto Flash: In low light conditions the flash will automatically activate. • Capture mode: The capture mode that you have selected. o 1P: Single image capturing per PIR triggering. o 2P: Two images continuous capturing per PIR triggering. o 3P: Three images continuous capturing per PIR triggering. o Video: Taking 10 seconds video per PIR triggering.
STC-WD3 pixels image. (Medium image quality) o 640 x 480 VGA: Select this option to capture a 300K pixels image. (Low image quality) o 320 x 240 Video resolution: This is the resolution during Video capturing and resolution is 100K pixels. • Batteries Status: It shows the battery status. o Full: It shows the batteries are full. o Half: It shows the batteries are half. o Low: It shows the batteries are low and front battery indicator will be on also.
STC-WD3 Programming the Stealth Cam STC-WD3 Switch the camera to the ON position. Once the Camera status screen is visible press the MENU button. This will bring up the SETTING screen. Capture mode / Resolution / Time out / TV System / Date & Time settings are all performed in this menu. Set the Capturing sequence. The Stealth Cam STC-WD3 can be programmed to shoot 1-3 pictures per triggering or 10 seconds of video.
• STC-WD3 Power on the unit, press the [MENU] button to bring up the menu on the LCD screen. • Press [UP] or [DN] to highlight CAPTURE • Then press the [OK] button to enter capture setting. • Press the [UP] or [DN] button to select the desired capture setting (number of pictures per triggering) and press the [OK] to save. This will return you to the SETTING SCREEN menu. • Use the UP and DOWN buttons to select additional program settings or press [MENU] again to exit the SETTING SCREEN.
• STC-WD3 Use the UP and DOWN buttons to select additional program settings or press [MENU] again to exit the SETTING SCREEN. Set the Time out: • Press the [UP] or [DN] button to highlight TIME OUT. • Press [OK] to enter the setting. • Press [UP] or [DN] button to set the desired time out in minutes (one minute increments from 1-10 and five minute increments from 10 to 60 minutes). • Press [OK] again to save the setting. This will return you to the SETTING SCREEN menu.
STC-WD3 Set TV System: NTSC is the correct setting for all of North America. Your Stealth Cam STC-WD3 comes pre-programmed for NTSC. • Press the [UP] or [DN] button to highlight TV OUT. • Press [OK] to enter the setting. • Press the [UP] or [DN] to set the TV output in NTSC or PAL system. • Press [OK] again to save the setting. This will return you to the SETTING SCREEN menu. • Use the UP and DOWN buttons to select additional program settings or press [MENU] again to exit the SETTING SCREEN.
STC-WD3 Set Date and Time: This camera uses the 24hr military time format. • Press the [UP] or [DN] button to move to highlight DATE AND TIME. • Press [OK] to enter the TIME & DATE setting menu. • Press [UP] or [DN] to select the TIME • Using the UP and DOWN buttons set the appropriate hour then press OK. This will highlight the minutes. Using the UP and DOWN buttons select the appropriate minute. • Press the [OK] to save the time and this will return you to the TIME & DATE setting menu.
STC-WD3 will bring you to the year setting. Using the UP or DN buttons select the appropriate year then press OK. This will return you to the DATE & TIME setting menu. • Press the [MENU] to return to the main setting menu. Once all settings have been completed press the MENU button to return to CAMERA STATUS screen. If no buttons are pressed within 30 seconds, the unit will return 1minute count down mode then start PIR capturing. www.stealthcam.
STC-WD3 Using the camera . Once all program setting have been completed your Stealth Cam is ready for field use. Getting started. Mounting the Camera. It is recommended to mount the camera 5-6 ft off the ground with the camera pointed at a slight downward angle. Be sure to avoid mounting the camera facing east or west as the rising and setting of the sun could produce false triggers and overexposed images.
STC-WD3 PIR Coverage Area Diagram www.stealthcam.
STC-WD3 Mounting the camera with the supplied Tree Screw. • Hand twist the screw into the tree or post at the desired position. • Attached the camera to the screw by turning the camera onto the mounting screw to the desired position. • Tighten the stabilizer nut. Attached camera to tree screw. Do not over tighten as this may cause damage to camera housing. Using the supplied www.stealthcam.
STC-WD3 nut and washer, tighten to the bottom of camera for greater stability. Mounting the camera with the supplied strap. • Insert the strap through the strap slots on the rear housing. • Wrap the strap around the mounting surface. Secure the strap and tighten the buckle in order to secure the camera. www.stealthcam.
STC-WD3 Stealth Cam offers a Security Lock Bracket for uses exclusively with this camera. See included accessory card or call toll free 877-269-8490. In order to obtain proper weather resistance, please make sure that both door latches are securely locked in place. Adjust the PIR coverage distance. • This Stealth Cam offers the user a variable PIR distance. • The PIR dial has a near to far designation. • NEAR is approximately 15ft and FAR is approximately 30ft. • Select the desired coverage distance.
STC-WD3 Testing the camera coverage area. One of STC-WD3 Cam’s many features is the ability to test the coverage area. • After mounting the camera, open front housing and slide the power to ON. • After the font LCD screen has powered on. Press the [TEST] button (this must be done with in 30 seconds or the camera will enter count down mode) • Close the front housing. • Walk around in the front of the camera to see if you have mounted camera in the proper position.
• STC-WD3 When you have completed the testing the coverage area there are 2 methods for exiting the test mode: a. Open the front housing and press the [TEST] button to exit test mode. The camera will then enter count down mode for 1 minute and front green indicator will start blinking giving you one minute to leave the coverage area. Then the camera will enter PIR detection mode. b.
STC-WD3 Using the camera in PIR detection mode. • Mount the camera to tree or other sturdy object using either two supplied tree screw or mounting strap (Please refer to the mounting suggestions section in this manual) • Open the front housing and move the switch to the ON position. At this point you have 30 seconds to make any program adjustments. • After 30 seconds the camera’s green test light will begin blinking and enter count down mode.
STC-WD3 The time between motion detection and the camera taking the pictures may vary due to lighting conditions, charging of the flash, program setting and battery power level. The flash lighting will only activate in low light conditions. When the camera is set to AVI capturing, the 10 seconds clips will only turn out well in good daytime lighting conditions. If the lighting conditions are not enough, unit will switch the AVI to single image capturing automatically.
STC-WD3 Using the camera by manual shoot. • Open the front housing and turn the camera on. • Program the capture mode to manual (Please refer to Program & Set up section on page 11 of this manual) • Close the front housing. • The camera is now ready to be used as hand held point and shoot camera. • Use the optical viewfinder to align your shot then press the shutter button. • When taking nighttime pictures allow approximately 6 seconds between shots to allow the flash to charge.
STC-WD3 Viewing and deleting the images. The STC-WD3 cam offers the user four different options for viewing the images. The external LCD display screen on the front housing will show the number of images in memory. To wake the camera from PIR detection mode press and hold either the UP or DN button for about 5 seconds. Once the CAMERA STATUS screen appears select OK to enter the DELETE & FORMAT menu. The instructions below are based on starting from a camera that is turned off. www.stealthcam.
STC-WD3 Thumbnail display Viewing the image on the built in TFT LCD screen. • Slide the camera power switch to ON. • Press the OK button. • A thumbnail view of the images in memory will be displayed. • Using the UP and DN buttons select the image you wish to view. This will bring up the whole image on the screen. Then using the UP and DN buttons you may navigate though all the images in memory. • To return to the thumbnail view from the full size image press the OK button. www.stealthcam.
STC-WD3 Viewing the image on a handheld LCD TV video monitor. (cable included) • Attach the appropriate cable to the video out jack on the camera. Insert the other end into the video in jack on handheld LCD TV monitor. Turn on both the camera and TV monitor. • Press the OK button on the camera. • A thumbnail view of the images in memory will be displayed on the TV screen. • Using the UP and DN buttons select the image you wish to view this will bring up the whole image on the screen.
STC-WD3 Viewing the images on your home TV equipped with an RCA input jack. (cable included) • Attach the appropriate cable to the video out jack on the camera. Insert the other end into the RCA video in jack on the TV. Turn on both the camera and TV. Make sure to switch to VIDEO IN mode on your TV. (See your TV owner’s manual for directions. • Press the OK button on the camera. • A thumbnail view of the images in memory will be displayed on the TV screen.
STC-WD3 the OK button. Viewing images by computer download The Stealth Cam STC-WD3 advanced Digital Scouting Camera is a plug and play USB storage device. This means users of Windows 2000 / ME / and XP operating system need not install the camera driver. This camera is not MAC compatible. The disc included in this package contains the camera driver for older operating systems as well as Ulead Photo Explorer imaging software for image enhancement and manipulation.
STC-WD3 Software installation. • Unplug the USB cable from PC. • Insert the CDROM in CD driver of your PC. • The auto-run program will execute. • Follow the instructions shown on screen from your PC to completely install the driver and application program. • Restart windows. • Successful installation will create “Ulead Photo Explorer” icon on you desktop. • Connect your camera to the PC by the USB cable, the PC will recognize the new device and set UP the configuration of the PC automatically.
STC-WD3 Once the CAMERA STATUS screen appears select OK to enter the Thumbnail View of images. From the Thumbnail screen press MENU to enter DELETE & FORMAT menu. • If your computer doesn’t run automatically, please click “Start” button and choose “Run”, and then browse the CD drive and click “Setup”. • Operation manual of Ulead Photo Explorer is contained on the provided CDROM. www.stealthcam.
STC-WD3 Viewing the images on your computer using the provided software. Please refer to Installation section on above to install the software and application program properly. • Slide the power switch to OFF location. • To view the images simply plug one end of the USB cable into an available USB port on your computer. • Plug the other end of USB cable into the camera. The camera will automatically power ON and display a USB icon on the LCD screen.
STC-WD3 • While viewing images either in thumbnail view or full screen press MENU to enter the DELETE & FORMAT menu. • Using the UP and DN buttons to the desired function. Delete, Not delete or Delete ALL. • After selection has been made the screen will go back to image preview mode. Using the external solar power. This Stealth Cam is designed to be used with an optional Stealth Cam solar panel accessory kit. (sold separately) • Make sure the camera is turned to OFF.
• STC-WD3 Adjust the solar panel’s receiving side toward the sufficient sun light direction. • Insert the solar panel’s plug into the solar jack of the bottom of camera housing • Slide the power source switch to SOLAR position to start the charging. When use the rechargeable battery connecting to solar panel, please always make sure the camera power source switch is on SOLAR position. Also make sure to install the rechargeable in correct polarity (+/-).
STC-WD3 CF Memory Card Compatibility Chart The following cards have been tested and approved for use in the Stealth Cam STC-WD3 model.
STC-WD3 Technical Specifications. System Requirements and Compatibility. • Windows 98/98se/2000/Me/XP. • P 450MHz or equivalent processor. • 128MB SDRAM or above. • VGA Video Card with 32MB RAM for minimum, Color 16 bit or higher. • An available CDROM driver and an available USB Port. • 600 MB free hard disc space. • Optional: Windows compatible sound card, Microphone and speaker. If you have any questions regarding your PC specifications please call your PC manufacturer. www.stealthcam.
STC-WD3 Camera Features and Specification. • Image sensor: 3.0 mega-pixels RGB color. • Built in 1.8” Color TFT display with backlight. • Built in 32M flash memories for image storage. • Ext memory support: CF memory card up to 2.0G. • Resolution Options: VGA, 1.3M, 2.0M, 3.0M • 4 Capturing Options: Manual, Single, Continuous, AVI. • Image performance for video stream: 10fps in 320 x 240 pixels, approx 10 seconds per section. • Auto white balance and auto expose.
STC-WD3 • Battery low indicator. • Green Test LED indicator • TV out support for NTSC and PAL system. • Focusing: 1.5m min to Infinity. • High precision 6 P glass lens with IR coating. • Effective viewing Angle: 52 deg. • PIR detection angle 48 deg. • Adjustable PIR detection range up to 9 meter. • Low power consumption: Standby current: < 1mA. Capture current <150mA • Interface type: USB 1.1. • Power: C size alkaline Batteries x 6. • Ext power: Solar and 12 volts battery pack.
STC-WD3 General Information Storing conditions. • Operating Environment: 14 to 104 deg F (-10 to 40 deg C). 2085% relative humidity, non-condensing. Special care instructions!! • The camera is designed to be weather resistant. Never attempt to immerse the unit to water or any other liquid. This will damage the unit and void the warranty. • Use a soft lens cloth for cleaning lens. Avoid touching lens with fingers. • Remove dirt or stains with a soft cloth dampened with water or neutral detergent.
• STC-WD3 Avoid dropping the STC-WD3 cam on to hard ground. Do not disassemble the STC-WD3 cam. • Do not mix new and old batteries. • Do not open the camera for unauthorized service, This could cause serious damage to the unit and will void the warranty. This camera is a precision electronic device. Do not attempt to service this camera yourself, as opening or removing covers may expose you to dangerous voltage points or other risks. www.stealthcam.