Stealth Cam STC-WD3MT-RT User’s Manual Toll Free Customer Support 1-877-269-8490 www.stealthcam.net Version 1.
STC-WD3MT-RT For Customer Service or Warranty Information Call Toll Free 877-269-8490 Stealth Cam, LLC P.O. Box 211662 Bedford, Texas 76095 www.steatlhcam.net Stealth Cam Limited Warranty Your Stealth Cam is covered by a One Year Limited Warranty on parts & labor from the date of purchase. The warranty covers defects in workmanship & materials. The warranty does not apply to units, which have been damaged or abused intentionally or unintentionally.
STC-WD3MT-RT Manual Contents Warranty 2 Camera overview 4 Camera kit contents 8 Battery and memory Installation 9 Set up and programming 13 Using the camera 22 Viewing & Deleting images 31 Using Solar Panel 39 CF Memory Card Compatibility Chart 41 Technical Specs 42 General Information 45 Moon phase symbol chart 47 www.stealthcam.
STC-WD3MT-RT Camera overview Front housing image with major parts indication. For use with Stealth Cam cable or 12V Battery Box. (sold separately) www.stealthcam.
STC-WD3MT-RT Open view image with major parts indication www.stealthcam.
STC-WD3MT-RT Side view with major parts indication For use with Stealth Cam exclusive Monitor / TV sold separately www.stealthcam.
STC-WD3MT-RT Picture / Image Capacity CF card High 3.0M Med 2.0M Low 1.3M Base 0.3M AVI (10 sec) 16MB 20 26 40 80 8 32MB 40 52 80 160 16 64MB 80 104 160 320 32 128MB 160 208 320 640 64 256MB 320 416 640 1280 128 512MB 640 832 1280 2560 256 1G 1280 1664 2560 5120 512 2G 2560 3328 5120 10240 1024 NOTE: Picture / Image Capacity Chart provides approximate number of images or AVI movies based on resolution setting and the size of memory card.
STC-WD3MT-RT Camera kit contents • Model STC-WD3MT-RT Digital Scouting Camera • CDROM (Contains Ulead Photo Express 8 and camera driver) • User Manual • 1.5M USB cable • 1.5M TV out cable for TV (RCA Jack) • 1.5M TV out cable for handheld TV (Mini Jack) • Strap • Tree screw with nut • Washer x 2 • Lock Plate www.stealthcam.
STC-WD3MT-RT Battery & memory installation Warning: Do not use different Voltage lead acid battery other than the one specified in this section. Doing so will damage the camera and will void the warranty. The Stealth Cam STC-WD3MT-RT Advanced Digital Scouting Camera is designed to operate using two different types of battery power options. NOTE: Always have camera in OFF position when installing or removing batteries. Batteries “C” cell The internal battery compartment accepts 6 “C” cell batteries.
STC-WD3MT-RT 12V Lead Acid external battery The STC-WD3MT-RT is equipped with an external power jack designed to accept a barrel plug cable to attach to a sealed lead acid battery. (sold separately). Battery cable and complete 12V Lead Acid battery kits are available wherever Stealth Cam scouting cameras are sold or call toll free 877-269-8490. Only Stealth Cam external battery accessories are recommended. • Make sure the camera power switch is OFF and power source switch on BATTERY.
STC-WD3MT-RT Memory Options Your STC-WD3MT-RT camera is equipped with 32MB built in flash memory. The camera is also equipped with an expendable media card slot capable accepting up to 2GB Compact Flash card (sold separately.) With no memory card inserted into the slot, the camera will use the built in 32MB memory. If a Compact Flash card is inserted into the slot then the camera will bypass the built in memory and utilize the compact flash memory.
STC-WD3MT-RT Compact flash cards must be clean (no images from other sources), if you are using the CF card from other cameras, please make sure to format the CF card prior use in the STC-WD3MT-RT. New cards are good to use straight from the package. www.stealthcam.
STC-WD3MT-RT Set up and Programming. When the camera is first turned on the internal LCD screen displays the camera status. The following information is present on this screen. If no buttons are pressed after 30 seconds the LCD screen will power down to conserve battery life. To re-power the screen press and hold the UP or DOWN button for at least 5 seconds. • Time out: To set the amount of time in minutes the camera will sleep between PIR triggering.
o • • STC-WD3MT-RT Flash Off: Turn off flash light Capture mode: The capture mode that you have selected. o 1P: Single image capturing per PIR triggering. o 2P: Two images continuous capturing per PIR triggering. o 3P: Three images continuous capturing per PIR triggering. o Video: Taking 10 seconds video per PIR triggering. o Manual: Manual capturing by press manual shutter to operate only. (use as point and shoot camera) Resolution: The resolution selection that you have selected. o 3.
• STC-WD3MT-RT Batteries Status: It shows the battery status. o Full: It shows the batteries are full. o Half: It shows the batteries are half. o Low: It shows the batteries are low and front battery indicator will be on also. When the camera has detected low batteries, (Batteries are lower then 6.6 +/-0.2Volts) the camera unit will power off within 30 seconds automatically. Please replace with new batteries; otherwise the camera will not work properly.
STC-WD3MT-RT Programming the Stealth Cam STC-WD3MT-RT Switch the camera to the ON position. Once the Camera status screen is visible press the MENU button. This will bring up the SETTING screen. Capture mode / Resolution / Time out / TV System / Date & Time settings are all performed in this menu. Set the Capturing sequence. The Stealth Cam STC-WD3MT-RT can be programmed to shoot 13 pictures per triggering or 10 seconds of video.
• STC-WD3MT-RT Power on the unit, press the [MENU] button to bring up the menu on the LCD screen. • Press [UP] or [DN] to highlight CAPTURE • Then press the [OK] button to enter capture setting. • Press the [UP] or [DN] button to select the desired capture setting (number of pictures per triggering) and press the [OK] to save. This will return you to the SETTING SCREEN menu. • Use the UP and DOWN buttons to select additional program settings or press [MENU] again to exit the SETTING SCREEN.
STC-WD3MT-RT Set the Time out: • Press the [UP] or [DN] button to highlight TIME OUT. • Press [OK] to enter the setting. • Press [UP] or [DN] button to set the desired time out in minutes (one minute increment from 1-10 and five minute increments from 10 to 60 minutes). • Press [OK] again to save the setting. This will return you to the SETTING SCREEN menu. • Use the UP and DOWN buttons to select additional program settings or press [MENU] again to exit the SETTING SCREEN.
• STC-WD3MT-RT Press the [UP] or [DN] to set the TV output in NTSC or PAL system. • Press [OK] again to save the setting. This will return you to the SETTING SCREEN menu. • Use the UP and DOWN buttons to select additional program settings or press [MENU] again to exit the SETTING SCREEN. If no buttons are pressed within 30 seconds, the unit will return one minute count down mode then start PIR capturing. Set Date and Time: This camera uses the 24hr military time format.
• STC-WD3MT-RT Press the [OK] to save the time and this will return you to the TIME & DATE setting menu. • Press [UP] or [DN] to select DATE and press the [OK] • Using the UP or DN buttons select the appropriate month then press OK. This will bring you to the day setting. Using the UP or DN buttons select the appropriate day then press OK. This will bring you to the year setting. Using the UP or DN buttons select the appropriate year then press OK. This will return you to the DATE & TIME setting menu.
STC-WD3MT-RT Flash Strobe Control: The camera is pre-program with Auto Flash setting. • Switch the camera to ON position. • To turn off the flash strobe, press the UP button once within 30 seconds. A icon will appear on the top of the screen. • To turn on the flash strobe back to Auto setting, press the UP button the second time. A icon will appear on the top of the screen. www.stealthcam.
STC-WD3MT-RT Using the camera Once all program setting has been completed, your Stealth Cam is ready for field use. Getting started Mounting the Camera. It is recommended to mount the camera 5-6 ft off the ground with the camera pointed at a slight downward angle. Be sure to avoid mounting the camera facing east or west as the rising and setting of the sun could produce false triggers and overexposed images.
STC-WD3MT-RT PIR Coverage Area Diagram www.stealthcam.
STC-WD3MT-RT Mounting the camera with the supplied Tree Screw • Hand twist the screw into the tree or post at the desired position. • Attached the camera to the screw by turning the camera onto the mounting screw to the desired position. • Tighten the stabilizer nut. Attached camera to tree screw. Do not over tighten as this may cause damage to camera housing. Using the supplied nut and washer, tighten to the bottom of camera for greater stability. www.stealthcam.
STC-WD3MT-RT Mounting the camera with the supplied strap • Insert the strap through the strap slots on the rear housing. • Wrap the strap around the mounting surface. Secure the strap and tighten the buckle in order to secure the camera. Stealth Cam offers a Security Lock Bracket for uses exclusively with this camera. See included accessory card or call toll free 877-269-8490. In order to obtain proper weather resistance, please make sure that both door latches are securely locked in place. www.
STC-WD3MT-RT Adjust the PIR coverage distance • This Stealth Cam offers the user a variable PIR distance. • The PIR dial has a near to far designation. • NEAR is approximately 15ft and FAR is approximately 30ft. • Select the desired coverage distance. (see PIR Coverage Diagram on page 22 for reference.) Testing the camera coverage area One of STC-WD3MT-RT Cam’s many features is the ability to test the coverage area. • After mounting the camera, open front housing and slide the power to ON.
STC-WD3MT-RT • Walk around in the front of the camera to see if you have mounted camera in the proper position. A green indicator light on the front will blink on when you have intruded the coverage area. • Adjust the camera position as needed and repeat testing until the desired coverage area is achieved. • When you have completed the testing the coverage area there are 2 methods for exiting the test mode: a. Open the front housing and press the [TEST] button to exit test mode.
STC-WD3MT-RT Using the camera in PIR detection mode • Mount the camera to tree or other sturdy object using either two supplied tree screw or mounting strap (Please refer to the mounting suggestions section in this manual) • Open the front housing and move the switch to the ON position. At this point you have 30 seconds to make any program adjustments. • After 30 seconds the camera’s green test light will begin blinking and enter count down mode.
STC-WD3MT-RT When the camera is set to AVI capturing, the 10 seconds clips will only turn out well in good daytime lighting conditions. If the lighting conditions are not enough, unit will switch the AVI to single image capturing automatically. When using the AVI function, the camera cannot use the flash. Time/Date stamp will not appear on the AVI video clips. Using the camera by manual shoot • Open the front housing and turn the camera on.
STC-WD3MT-RT • When taking nighttime pictures allow approximately 6 seconds between shots to allow the flash to charge. In case of low battery power, it will take longer to charge the flash between pictures. www.stealthcam.
STC-WD3MT-RT Viewing and deleting the images. The STC-WD3MT-RT cam offers the user four different options for viewing the images. The external LCD display screen on the front housing will show the number of images in memory To wake the camera from PIR detection mode press and hold either the UP or DN button for about 5 seconds. Once the CAMERA STATUS screen appears select OK to enter the DELETE & FORMAT menu. The instructions below are based on starting from a camera that is turned off.
STC-WD3MT-RT Viewing the image on the built in TFT LCD screen • Slide the camera power switch to ON. • Press the OK button. • A thumbnail view of the images in memory will be displayed. • Using the UP and DN buttons select the image you wish to view. This will bring up the whole image on the screen. Then using the UP and DN buttons you may navigate though all the images in memory. • To return to the thumbnail view from the full size image press the OK button.
• STC-WD3MT-RT A thumbnail view of the images in memory will be displayed on the TV screen. • Using the UP and DN buttons select the image you wish to view this will bring up the whole image on the screen. Then using the UP and DN buttons you may navigate though all the images in memory. • To return to the thumbnail view from the full size image press the OK button. Viewing the images on your home TV equipped with an RCA input jack.
• • STC-WD3MT-RT Using the UP and DN buttons select the image you wish to view this will bring up the whole image on the screen. Then using the UP and DN buttons you may navigate though all the images in memory. To return to the thumbnail view from the full size image press the OK button. Viewing images by computer download The Stealth Cam STC-WD3MT-RT advanced Digital Scouting Camera is a plug and play USB storage device.
STC-WD3MT-RT Attention: The software CD-ROM packaged with the camera is designed for PC’s only (not MAC compatible). Playing this CD-ROM on a stereo or CD player may cause damage to it. Software installation • Unplug the USB cable from PC. • Insert the CDROM in CD driver of your PC. • The auto-run program will execute. • Follow the instructions shown on screen from your PC to completely install the driver and application program. • Restart windows.
• STC-WD3MT-RT NOTE: Users of Windows 98 or earlier must install camera driver prior to connecting the USB cable. • If your computer doesn’t run automatically, please click “Start” button and choose “Run”, and then browse the CD drive and click “Setup”. • Operation manual of Ulead Photo Explorer is contained on the provided CDROM. www.stealthcam.
STC-WD3MT-RT Viewing the images on your computer using the provided software Please refer to Installation section on above to install the software and application program properly. • Slide the power switch to OFF location. • To view the images simply plug one end of the USB cable into an available USB port on your computer. • Plug the other end of USB cable into the camera. The camera will automatically power ON and display a USB icon on the LCD screen.
STC-WD3MT-RT Deleting images At any time while viewing images on the built in LCD, Handheld TV or Home TV you may delete images one at a time or all at once. • While viewing images either in thumbnail view or full screen press MENU to enter the DELETE & FORMAT menu. • Using the UP and DN buttons to the desired function. Delete, Not delete or Delete ALL. • After selection has been made the screen will go back to image preview mode. www.stealthcam.
STC-WD3MT-RT Using the external solar power This Stealth Cam is designed to be used with an optional Stealth Cam solar panel accessory kit. (Sold separately) • Make sure the camera is turned to OFF. • Open the battery cover, • Insert 6 C size rechargeable batteries into battery compartment and close the battery door. • Adjust the solar panel’s receiving side toward the sufficient sun light direction.
STC-WD3MT-RT Also make sure to install the rechargeable batteries in correct polarity (+/-). Incorrect voltage or polarity (+/-) will damage the camera. • For first time use, please leave the solar panel with camera power switch turned in OFF position for full daylight charging at least 20 hours. www.stealthcam.
STC-WD3MT-RT CF Memory Card Compatibility Chart The following cards have been tested and approved for use in the Stealth Cam STC-WD3MT-RT model.
STC-WD3MT-RT Technical Specifications System Requirements and Compatibility • Windows 98/98se/2000/Me/XP. • P 450MHz or equivalent processor. • 128MB SDRAM or above. • VGA Video Card with 32MB RAM for minimum, Color 16 bit or higher. • An available CDROM driver and an available USB Port. • 600 MB free hard disc space. • Optional: Windows compatible sound card, Microphone and speaker. If you have any questions regarding your PC specifications please call your PC manufacturer. www.stealthcam.
STC-WD3MT-RT Camera Features and Specification. • Image sensor: 3.0 mega-pixels RGB color. • Built in 1.8” Color TFT display with backlight. • Built in 32M flash memories for image storage. • External memory support: CF memory card up to 2.0G. • Resolution Options: VGA, 1.3M, 2.0M, 3.0M • 4 Capturing Options: Manual, Single, Continuous, AVI. • Image performance for video stream: 10fps in 320 x 240 pixels, approx 10 seconds per section. • Auto white balance and auto expose.
• STC-WD3MT-RT TV out support for NTSC and PAL system. • Focusing: 1.5m min to Infinity. • High precision 6 P glass lens with IR coating. • Effective viewing Angle: 52 deg. • PIR detection angle 48 deg. • Adjustable PIR detection range up to 9 meter. • Low power consumption: Standby current: < 1mA. Capture current <150mA • Interface type: USB 1.1. • Power: C size alkaline Batteries x 6. • External power: Solar and 12 volts battery pack. • Image format: Standard JEPG.
STC-WD3MT-RT General Information Storing conditions • Operating Environment: 14 to 104 deg F (-10 to 40 deg C). 2085% relative humidity, non-condensing. Special care instructions!! • The camera is designed to be weather resistant. Never attempt to immerse the unit to water or any other liquid. This will damage the unit and void the warranty. • Use a soft lens cloth for cleaning lens. Avoid touching lens with fingers. • Remove dirt or stains with a soft cloth dampened with water or neutral detergent.
• • STC-WD3MT-RT Do not mix new and old batteries. Do not open the camera for unauthorized service. This could cause serious damage to the unit and will void the warranty. This camera is a precision electronic device. Do not attempt to service this camera yourself, as opening or removing covers may expose you to dangerous voltage points or other risks. www.stealthcam.
STC-WD3MT-RT Moon Phase Symbol Chart www.stealthcam.
