TITAN INSTRUCTION MANUAL Model #: STC-‐Z3IR Toll Free 1-‐877-‐269-‐8490 WWW.STEALTHCAM.COM Version 1.
** IMPORTANT NOTE ** First, congratulations on purchasing one of the finest scouting cameras on the market today. We appreciate your business and want to prove to you we are committed to providing you the best product and support in the field.
TABLE OF CONTENTS Camera overview 4 Camera kit contents 7 General Information 8 Quick Start 9 Battery and Memory Installation 10 Setup and Programming 13 Using the camera 21 Viewing & deleting images 25 Memory compatibility chart 33 Technical specs 34 Image capacity chart 37 Moon phase chart 39 Frequently Asked Questions (FAQs) 40 FCC Compliance 42 WWW.STEALTHCAM.
CAMERA OVERVIEW Front 1:IR LED window 2:Low voltage warning RED LED 3:PIR sensing GREEN LED 4:Lens 5:LCD display 6:Menu button M 7:Confirm button 8:Downward button ▼ 9:Upward button ▲ 10:PIR sensing window 11:Microphone hole 12:External power jack 13:1/4 inch screw mounting hole 14:Buckle 15:Silicon locking hole WWW.STEALTHCAM.
Inside 16:SD card slot 17: Function button (ON, TEST/SET、OFF ) 18:USB jack 19:Battery compartment WWW.STEALTHCAM.
DIAGRAM: How to close the door latch CAMERA KIT CONTENT • Model STC-Z3IR Digital Scouting Camera • User manual • Strap WWW.STEALTHCAM.
GENERAL INFORMATION Storing conditions • Operating Environment: 14 to 104 deg F (-‐10 to 40 deg C). 20-‐85% relative humidity, non-‐condensing. Special care instructions!! • The camera is designed to be weather resistant. Never attempt to immerse the unit in water or any other liquid. This will damage the unit and void the warranty.
QUICK START GUIDE This guide is designed to get you up and running in a matter of moments. To get the most out of this advanced scouting tools, please read the manual thoroughly before operating the camera.
BATTERY AND MEMORY INSTALLATION WARNING: Do not use different Voltage lead acid battery other than the one specified in this section. Doing so will damage the camera and will void the warranty. WARNING: ALWAYS have the camera in the OFF position when installing or removing batteries and memory card. Removing batteries or memory card while the camera is ON may damage the camera.
NOTE: Please make sure the voltage and polarity (+/-‐) are correct before connection. Incorrect voltage or polarity (+/-‐) will damage the camera. When both internal and external batteries are connected, the camera will draw power from the higher voltage source first.
Inserting SD memory card NOTE: Make sure camera is in the OFF position whenever adding or removing memory. • Insert SD memory card in to the SD card slot completely and in the correct direction as shown by the sticker located at the side of the housing.
LCD Display Icons 1. Locked icon (This represents that any programming is NOT allowed. All setting buttons on front panel are disabled) 2. Unlocked icon (This represents camera power switch to SET mode, allow customer to do programming by using setting buttons on front panel) 3.
8. Resolution icon (This represents the camera is in Resolution Mode setting) a. High Resolution – 3M Pixel / Low Resolution – 1.3M Pixel 9. Delete/Format icon (This represents the camera is in deleting pictures/videos or format mode) 10. [Reserved for future use] 11.
SETUP AND PROGRAMMING • • • • • Programming is only allowed when camera’s power switch is at the TEST/SET mode. Slide the power switch from OFF to TEST/SET position; you will hear two faint short beeps. Touch M button to enter Picture or Video mode selection. Picture icon will blink.
• Camera is now ready for the field. If your camera is already in the TEST/SET position, you may slide the power switch to the ON position. If you’re not ready to use the camera, simply slide the power switch to the OFF position. • When ready to use, position your camera in the field.
To set Date and Time • To enter Date/Time setting, slide the power switch to TEST/SET position. • Press and Hold the M button for at least 3 seconds. Now the DATE and TIME icon will blink. • Touch ▲ button to choose DATE setting. • Touch ▲ or ▼ button to increase or decrease your Month selection.
USING THE CAMERA Once all program settings have been setup properly, your Stealth Cam is ready for field use. Getting started Listed below are some helpful pointers on how to use your camera to get the best results. • Mount the camera about 4-‐5 feet high with the camera pointed at a slight downward angle.
(Example: Mounting) (Example: Trail Setup) WWW.STEALTHCAM.
MEMORY COMPATIBILITY CHART The following cards have been tested and approved for use with the STC-‐ DVIRHD model at the time this manual was printer. For a more up-‐to-‐date chart visit our website at www.stealthcam.net.
TECHNICAL SPECIFICATIONS System Requirements and Compatibility • Windows Me/2000/XP/Vista/Windows 7 (Check our website for Mac compatibility listings) • Pentium 4, 2GHz or above • 1GB RAM (2GB recommended) • 32 bits color, Resolution 1280 x 800 or above with built in 256MB • 2GB free hard disc space • An available USB 1.1 port (USB 2.
Camera Features and Specification • Camera lens: 5P high precision multi-‐layer glass lens with IR coating • Built in 2.0” B&W LCD display • Built in 64MB flash memories for image storage • External memory support: SD memory card up to 16GB. See compatibility chart. • Resolution Options: 3.0M, 1.
• Effective viewing Angle: 50 degrees • PIR detection angle 48 degrees • Power consumption: Standby current: < 7mA. Capture current <280mA • Interface type: USB 1.1 • Power: AA size alkaline Batteries x 8 • External power: 12 volts battery pack / AC Adapter WWW.STEALTHCAM.
IMAGE CAPACITY CHART STC-Z3IR Day Memory Card Size Resolution Piexls Data size HiGH 8.0M 4.7M 3264 x 2448 217 434 868 1,736 3,472 LOW 3.0M 2M 2048 x 1536 512 1,024 2,048 4,096 8,192 BASE 1.3M 1M 1280 x 1024 1,024 2,048 4,096 8,192 16,384 AVI VGA 30's VGA 80M 640 x 480 / 30's 14 28 56 112 224 HIGH 8.0M 2.7M 3264 x 2448 340 680 1,360 2,720 5,440 LOW 3.0M 1M 2048 x 1536 1,024 2,048 4,096 8,192 16,384 BASE 1.3M 0.
When the SD card is NOT FULL, but camera's front counter already reaches 9999, the camera will create a new folder to save the next data. Camera's front counter will keep showing 9999. It will not reset to 0000.
MOON PHASE SYMBOL CHART WWW.STEALTHCAM.
FREQUENTLY ASKED QUESTIONS Q: What does it mean when I have all 8’s on my LCD screen? A: This usually refers to an incompatible memory card or memory card damaged. Make sure your card has been properly formatted. Q: Is the infrared flash invisible? A: The infrared flash will give off a low glow red light.
Q: What are my options if my camera is past it warranty? A: We have an out of warranty program in which you may purchase a reconditioned replacement unit for 50% or more off (based on retail price of unit) discount exchange of your old unit.
WARNING: Modification not approved by the party responsible for compliance could void user’s authority to operate. FCC Compliance This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of the FCC Rules.