INSTRUCTION MANUAL MODEL: STC-‐ZX24 V.
**IMPORTANT NOTE** To ensure the product is being utilized to its full potential, we recommend checking our website for new product updates. If your unit is having trouble, please check the website to determine you are using the latest firmware or software version. TECHNICAL SUPPORT EMAIL: Stealthcam@gsmorg.com Please allow 48 hours for email response. STEALTHCAM LLC P.O.
TABLE OF CONTENTS Camera Overview Quick Start Guide General Information Camera Programming Quick Set 1 (Q1) Quick Set 2 (Q2) Quick Set 3 (Q3) Custom Settings Test Mode Memory Card Installation Formatting Battery Removal & Installation View and Deleting files Definitions Frequently Asked Questions (FAQs) FCC Compliance Limited Warranty Information www.stealthcam.
CAMERA OVERVIEW Front Open Bottom www.stealthcam.
CAMERA OVERVIEW (CONT) Back Side Battery Tray www.stealthcam.
QUICK START GUIDE Power Options (Select one) 1. Insert 6 ‘AA’ batteries into the Battery Tray. Slide Battery Tray into the bottom of the ZX24 camera until it is secured. (See page 21 for more details) 2. Connect 12V Battery Box to the bottom of the unit under the AUX POWER 12V DC gasket. Memory Insert a clean Class 10 SD memory card, between 2GB and 32GB into memory card slot.
GENERAL INFORMATION Storing conditions Operating Environment: 14 to 104 deg F (-‐10 to 40 deg C). 20-‐85% relative humidity, non-‐condensing. Special care instructions!! The camera is designed to be weather resistant. Never attempt to immerse the unit in water or any other liquid. This will damage the unit and void the warranty. Do not mix old and new batteries. Do not mix alkaline, standard, or rechargeable batteries.
CAMERA PROGRAMMING This ZX24 features six distinct modes of operation: Off / Q1 / Q2 /Q3 / Custom / Test. Each setting is activated based upon the position of the switch on the inside of the unit. Off – This position completely powers down the unit. Q1 – This is the first Quick Set programming mode.
CAMERA PROGRAMMING – CUSTOM (CONT) Custom – This is the fifth setting and is defined by the user. When the camera is changed to this mode, the display screen will reflect the last program setting: Number of images on the memory card, Countdown timer and Battery percentage. PHOTO 00000 00:30 100% The system default programming is set to 6.0MP, 5-‐second timeout delay and 1 Photo Burst.
CAMERA PROGRAMMING – CUSTOM (CONT) ! ! SETUP DATE – 01/01/15 (default): This setting is used to give the camera the correct date to use on the Info Bar of the images. The format is in a MM/DD/YY setup. With the MM (month) setting blinking, use the UP and DOWN arrows to be change the setting from 1 to 12.
CAMERA PROGRAMMING -‐ CUSTOM (CONT) " " TIME FORMAT – 12 HOUR (default): This setting is used to tell camera if the time programmed and displayed on the Info Bar should be in the basic 12 hour (AM/PM) format or the 24 hour (military) format. With this option blinking, pressing the UP or DOWN arrow buttons will cause the camera to cycle between the two options.
CAMERA PROGRAMMING -‐ CUSTOM (CONT) o PIR PHOTO (default): In this mode the camera will take a designated amount of picture with a designated time out when the camera senses activity in front of the unit. This mode is available for both day and night activities. " PHOTO RES – 6.0 MP (default): This setting is used to determine the Megapixel resolution of each image taken by the camera.
CAMERA PROGRAMMING -‐ CUSTOM (CONT) o PIR VIDEO: In this mode the camera will take a video clip at a designated resolution for a designated length with a designated time out when the camera senses activity in front of the unit. This mode is available for both day and night activities.
CAMERA PROGRAMMING -‐ CUSTOM (CONT) o TIME LAPSE: In this mode the camera will take a designated amount of pictures with a designated time out between the designated hours of operation even if there is no activity in front of the camera. " " " " PHOTO RES – 6.0 MP (default): This setting is used to determine the Megapixel resolution of each image taken by the camera.
CAMERA PROGRAMMING -‐ CUSTOM (CONT) " " Once this setting is on the appropriate hour, press the RIGHT arrow key to move to the MM (minute) setting and it will start to blink. Using the UP and DOWN arrows will allow the setting to be change from 00 to 59. Again when this setting is on the appropriate minute, press the RIGHT arrow key to move to the AP (am/pm) setting and it will start to blink.
CAMERA PROGRAMMING -‐ CUSTOM (CONT) ! ! ! ! CAMERA NAME – STEALTH CAM (default): This setting is used to identify the camera on the Info Bar. It can be up to 13 characters long in the form of alpha (A-‐Z), numeric (0-‐9), or spaces. With this option blinking, use the UP or DOWN arrow buttons to change the initial character.
CAMERA PROGRAMMING -‐ CUSTOM (CONT) o SECURITY KEY CONFIGURATION – 0000 (default): To change the key to an owner operated one press the ENTER button. With this option blinking, use the UP or DOWN arrow buttons change the first digit to the preferred number or letter. Then using the LEFT button, move to the second digit and change it to the preferred number or letter as well.
CAMERA PROGRAMMING ! LANGUAGE – ENGLISH (default): This new feature allows you to select which language you prefer to use in the menu. By pressing the ENTER button you will be able to scroll through the following choices: English / German / French / Spanish. Once selected press the ENTER button again to save your setting.
MEMORY CARD INSTALLATION To insert the SD memory card into the camera: first locate the SD card slot on the right hand side of the of the camera case. Next with the SD card label facing towards the front of the camera, insert the SD card. When the card has been pressed in fully there will be a noticeable resistance as the spring locking mechanism activates to hold on the SD card.
MEMORY CARD (CONT) FORMATTING SD CARD It always best to format your SD cards from the actual device your using, in this case the camera. This will allow the camera to format the card in the proper fashion. 1. First insert your SD memory card into the camera. 2. Slide the switch to the Custom setting. 3. Press the Menu. 4. Press the Up Arrow once. The display will show “Format Card – No” 5.
BATTERY REMOVAL & INSTALLATION To remove the batteries from the unit; open the case and press the EJECT button on the lower right hand corner. This will cause the battery tray to be released and slide downwards. New, Alkaline or Lithium, ‘AA’ batteries must be inserted with the orientation as shown on the tray.
VIEW & DELETING IMAGES The camera allows for two (2) ways to view your images. First is the direct connection for the camera to the computer via a USB cable (not included). This is a USB mini to standard USB (type A/B) cable.
DEFINITIONS REFLEX (Advanced Low-‐Light Sensitivity) – Ultra-‐fast trigger speed, averaging < 1 second with recovery times programmable as low as 5 seconds. MATRIX (Blur Reduction Technology) – Advanced blur reduction dramatically reduces blur effects resulting in sharper, clearer images. MULTI-‐ZONE DETECTION -‐ Provides for more accurate coverage at angle & distance, maximizing the cameras triggering capability.
FREQUENTLY ASKED QUESTIONS Q: Can I mix batteries together? A: NO, you should never mix old with new OR Alkaline with Lithium with Rechargeable. Q: Is my game camera Mac compatible? A: Yes, This camera model works with 10.6 and above.
FREQUENTLY ASKED QUESTIONS (CONT) Q: Can I use my game camera through a window or glass door? A: Glass may disrupt your sensor beam we don’t advise using the camera in this fashion.
FCC COMPLIANCE GSM STC-‐ZX24 NOTE: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
LIMITED WARRANTY INFORMATION Your Stealth Cam scouting camera is covered by a 365 Day Limited Warranty on parts and labor from the date of original purchase, and purchases must be made through an authorized dealer. The warranty covers defects in workmanship and materials. The warranty does not apply to units, which have been damaged or abused intentionally or unintentionally.
MANUEL D'INSTRUCTIONS MODÈLE: STC-‐ZX24 V.01 www.stealthcam.
**NOTE IMPORTANTE** Pour vous assurer que le produit soit utilisé à son plein potentiel, nous vous recommandons de vérifier notre site Web pour obtenir les nouvelles mises à jour du produit. Si votre appareil a des problèmes, veuillez consulter le site pour déterminer si vous utilisez le dernier micrologiciel ou la toute dernière version du logiciel.
TABLE DES MATIÈRES Aperçu de l'appareil photo Guide démarrage rapide Renseignements généraux Réglage de l'appareil photo Réglage rapide 1 (Q1) Réglage rapide 2 (Q2) Réglage rapide 3 (Q3) Paramètres personnalisés Mode Test 31 33 34 35 35 35 35 36-‐45 45 Carte mémoire Installation Formatage Installation et retrait de la pile Affichage et Suppression des fichiers
APERÇU DE L'APPAREIL PHOTO Devant ouvert Bas www.stealthcam.
APERÇU DE L'APPAREIL PHOTO (SUITE) Côté Arrière www.stealthcam.
GUIDE DE DÉMARRAGE RAPIDE 7 Options d'alimentation (Sélectionnez-‐en une) 1. Insérez 6 piles de type 'AA' dans le Compartiment à piles. Glissez le Compartiment à piles au bas de l'appareil photo ZX24 jusqu'à ce qu'il soit fixé. (Lisez la page 48 pour obtenir les détails) 2. Branchez le Boîtier à piles de 12 V au bas de l'appareil, sous le joint AUX POWER 12V DC (ALIMENTATION AUX 12 V CD).
RENSEIGNEMENTS GÉNÉRAUX Conditions de rangement Environnement d'exploitation : -‐10 à 40 deg C (14 à 104 deg F). 20 -‐ 85 % humidité relative, sans condensation. Instructions pour les soins spéciaux L'appareil photo est conçu pour résister à l'eau. N'essayez jamais de plonger l'appareil dans l'eau ou dans tout autre liquide. Ce qui pourrait endommager l'appareil et annuler la garantie. Ne pas mélanger piles neuves et anciennes.
RÉGLAGE DE L'APPAREIL PHOTO Ce ZX24 comprend 6 modes distincts d'opération : Arrêt/Q1/Q2/Q3/Personnalisé/Test. Chaque paramètre est activé en fonction de la position de l'interrupteur à l'intérieur de l'appareil. Arrêt – Cette position coupe complètement l'alimentation de l'appareil. Q1 – Il s'agit du premier mode de programmation de Réglage rapide (Quick Set).
RÉGLAGE DE L'APPAREIL PHOTO -‐ PERSONNALISÉ (SUITE) Personnalisé – Il s'agit du cinquième paramètre et est défini par l'utilisateur. Lorsque l'appareil est changé pour ce mode, l'écran d'affichage reflètera le dernier réglage du programme : Nombre d'images contenues sur la carte mémoire, la minuterie et le pourcentage de la pile. PHOTO 00000 00:30 100 % Le réglage par défaut du système est réglé à 6.
RÉGLAGE DE L'APPAREIL PHOTO -‐ PERSONNALISÉ (SUITE) ! ! RÉGLAGE DE LA DATE – 01/01/15 (par défaut) : Ce paramètre est utilisé pour indiquer la bonne date à la caméra à utiliser sur la Barre d'infos des images. Le format est MM/JJ/AAAA. Lorsque le MM (mois) clignote, utilisez les flèches vers le HAUT et vers le BAS pour passer de 1 à 12.
RÉGLAGE DE L'APPAREIL PHOTO -‐ PERSONNALISÉ (SUITE) ! ! FORMAT DE L'HEURE – 12 HEURES (par défaut) : Ce paramètre est utilisé pour indiquer à l'appareil photo si l'heure programmée et affichée sur la Barre d'infos doit être au format de base de 12 heures (AM/PM) ou au format 24 heures (militaire).
RÉGAGE DE L'APPAREIL PHOTO -‐ PERSONNALISÉ (SUITE) o PHOTO PIR (par défaut) : Dans ce mode, l'appareil photo prend une quantité désignée de photos dans un laps de temps établi lorsque l'appareil photo détecte une activité se déroulant devant l'appareil. Ce mode est disponible à la fois pour les activités de jour et de nuit. " " " " RÉS PHOTO – 6.
RÉGLAGE DE L'APPAREIL PHOTO -‐ PERSONNALISÉ (SUITE) o VIDÉO PIR : Dans ce mode, l'appareil photo prendre un clip vidéo à une résolution désignée pour une durée établie avec une temporisation spécifiées lorsque l'appareil photo détecte une activité se déroulant devant l'appareil. Ce mode est disponible à la fois pour les activités de jour et de nuit.
RÉGLAGE DE L'APPAREIL PHOTO -‐ PERSONNALISÉ (SUITE) o LAPSE DE TEMPS (Délai) : Dans ce mode, l'appareil photo prend une quantité désignée de photos dans un délai établi entre les heures d'opération désignée même s'il n'y a aucune activité devant l'appareil photo. " " " " RÉS PHOTO – 6.
RÉGLAGE DE L'APPAREIL PHOTO -‐ PERSONNALISÉ (SUITE) " " pour permettre au paramètre de changer de 1 à 12. Une fois ce paramètre sur la bonne heure, appuyez sur la flèche DROITE pour passer au réglage MM (minute) et ce dernier commencera à clignoter. Les flèches HAUT et permettront de changer entre 00 et 59.
RÉGLAGE DE L'APPAREIL PHOTO -‐ PERSONNALISÉ (SUITE) ! ! ! ! NOM DE L'APPAREIL PHOTO – STEALTH CAM (par défaut) : Ce paramètre est utilisé pour identifier l'appareil photo sur la Barre d'infos. Il peut compter jusqu'à 13 caractères sous forme alpha (A -‐ Z), numérique (0 -‐ 9), ou comporter des espaces.
RÉGLAGE DE L'APPAREIL PHOTO -‐ PERSONNALISÉ (SUITE) ! ! CLÉ DE SÉCURITÉ – 0000 (par défaut) : Pour modifier la clé d'un propriétaire utilisée, appuyez une fois sur le bouton Entrée. Lorsque cette option clignote, utilisez la flèche vers le HAUT ou vers le BAS pour changer le premier chiffre par un nombre ou une lettre désiré.
RÉGLAGE DE L'APPAREIL PHOTO ! ! LANGUE -‐ l'anglais (par défaut) : Cette nouvelle fonctionnalité vous permet de sélectionner la langue que vous préférez utiliser dans le menu . En appuyant sur la touche ENTER vous serez en mesure de faire défiler les options suivantes : Anglais / Allemand / Français / Espagnol . Une fois sélectionné, appuyez sur la touche ENTRER de nouveau pour enregistrer votre réglage .
CARTE MÉMOIRE -‐ INSTALLATION Pour insérer la carte mémoire SD dans l'appareil: localisez la fente de la carte SD sur le côté droit du boîtier de l'appareil photo. Ensuite, avec l'étiquette de la carte SD orientée vers l'avant de l'appareil photo, insérez la carte SD.
FOMATAGE DE LA CARTE SD Il est toujours mieux de formater vos cartes SD à partir de l'appareil actuel que vous utilisez, dans ce cas l'appareil photo. Ce qui permettra à l'appareil photo de formater la carte dans le mode approprié. 1. Insérez d'abord votre carte mémoire SD dans la caméra. 2. Glissez l'interrupteur au paramètre Personnalisé. 3. Appuyez sur Menu. 4.
INSTALLATION ET RETRAIT DE LA PILE Pour retirer les piles de l'appareil, ouvrez le boîtier et appuyez sur le bouton ÉJECTION situé dans le coin inférieur droit. Ce qui permettra de glisser et de retirer le Compartiment à piles. De nouvelles piles, alcalines ou au lithium, de type 'AA' doivent être insérées en respectant l'orientation indiquée sur le compartiment.
AFFICHAGE ET SUPPRESSION DES IMAGES La caméra offre deux (2) façons de voir vos images. La première est la connexion directe de l'appareil photo à l'ordinateur via un câble USB (non fourni). Il s'agit d'un mini câble USB vers un câble USB standard (type A/B).
DÉFINITIONS REFLEX (Sensibilité avancée à faible luminosité) -‐ Vitesse de déclenchement ultra-‐rapide, en moyenne < 1 seconde avec des temps de récupération programmables aussi bas que 5 secondes. MATRIX(Technologie de réduction du flou) – La réduction avancée du flou réduit de manière importante les effets du flou, résultant en des images plus claires et plus nettes.
FOIRE AUX QUESTIONS Q : Mon appareil de jeu pour Mac est-‐i compatible? R : Oui, ce modèle d'appareil photo fonctionne avec la version 10.6 et plus. Q : Puis-‐je utiliser des piles rechargeables dans l'appareil photo? R : Les piles rechargeables sont très bien pour l'appareil; les piles alcalines ordinaires conçues pour les appareils électroniques numériques sont recommandées pour obtenir une meilleure performance.
FOIRE AUX QUESTIONS (SUITE) Q : Puis-‐je utiliser mon appareil de jeu par une fenêtre ou une porte de verre? R : Le verre peut perturber le faisceau de votre détecteur; nous ne vous conseillons pas d'utiliser l'appareil photo dans ce mode.
CONFORMITÉ FCC Remarque : Cet équipement a été testé et se conforme aux exigences des appareils numériques de classe B, conformément à la partie 15 des Règles FCC. Ces limites sont conçues pour fournir une protection raisonnable contre les interférences nuisibles présentes dans une installation résidentielle.
RENSEIGNEMENTS SUR LA GARANTIE LIMITÉE Votre appareil photo d'exploration Stealth Cam est couverte par une garantie limitée de 365 jours sur les pièces et la main-‐d'œuvre à partir de la date d'achat initial, et les achats doivent être effectués auprès d'un revendeur autorisé. La garantie couvre les défauts de fabrication et les matériaux.