By Galaxy Series Installation & Operations Manual WS-112 Note: You must read all installation & operation instructions prior to assembly and use of this unit.
Table of Contents Tools Needed for Installation Product Features Unit Information Electrical Information Plumbing Requirements General Information Base Information Assembly & Installation Handle Assembly Temperature adjustments Diverter Maintenance & Care Cleaning & Maintenance Steam Generator Cleaning General use & Maintenance Control Parts Information LCD Display Information Control Panel Diagram Control Procedures Wireless FM Transmitter Information Troubleshooting ……………………………………………. …………………………………………….
TOOLS REQUIRED FOR INSTALLATION: Level Screw driver #2 Phillips Silicone Wrench Electric Drill Square Ruler Rubber mallet PRODUCT FEATURES DESCRIPTION WS112(32) WS112(36) WS112(40) 4.
ELECTRICAL INFORMATION 1 dedicated 12-2 wire with 20 amp GFCI breaker (220V) Connect the overhead light, speaker, fan, CD, telephone according to the tags on the wires. Do not connect the wire “O3” to anything. Connect main power supply. PLUMBING INFORMATION The unit is equipped with 3 ft. hot and cold, metal braided water supply hose with ½-inch national pipe thread to connect from faucet/manifold (Manifold is located. 4 ft.
BASE OPTIONS The standard WS-112 shower enclosure does not include a base. It can be installed over a custom or existing base of your choice. Steam Planet offers one base option: A man made “cultured stone” base (Black or White) that sets into place or may require some type of cement/thin set mortar foundation. You will find information regarding these bases below. OPTIONAL STONE BASE: Stone Base needs to be set in the final resting space and leveled.
INSTALLATION INSTRUCTIONS FOR WS112 ALL SIZES 1. The distance between Wall A and Wall B should be at least 1510mm (59.5 inches). 2. The minimum height for the unit (not including any base) is 84.5 inches. 4. To assemble front frame you will need at least 6” #2 Philips bit. It is advised to use an impact driver. Do not over tighten. 5. Each 5” frame sidepieces has 2 grey rubber gaskets on top and bottom. Bottom piece has to be all way down, top piece – all way to the top. 6.
Note: Panel with hinge holes goes on the left side. Install the front fixed glass panels. Remove plastic clip in horizontal frame, slide glass in place, and reattach clip to hold glass into place. Do the same for the right side. INSTALLING THE CEILING 1. Connect the power to the fan, light, and speaker plugs. The accessories are marked. 2. Align holes on the left, right, and back side, with the holes on the left, back, and side panels. 3.
INSTALL THE GASKETS 1. Once all is connected, place the wooden shower grid floors and benches inside the unit. 2. Please, do not use the unit for at least 24hours or until the silicone is completely dried. ________________________________________________________________________________________________ HANDLE ASSEMBLY TRIM FLANGE ATTACHMENT Position Flange (A) on the Valve (B) with drain hole (C) at the bottom. Place Protective Washer (D) on the short end of the reversible Retainer Sleeve (E).
TEMPERATURE ADJUSTMENTS MAINTENANCE & CARE Disassembly: 1. Replacement parts may be available at Lowes or Home Depot. 2. When replacement parts are not available, please write or call Price Pfister Consumer Service. 3. Always turn off water and release pressure before working on your faucet. Note: Trim Care Cleaning instructions: For all Handles and decorative finishes, use only a soft damp cloth to clean and shine. Use of polish, detergents, abrasive cleaners, organic solvents or acid may cause damage.
Turn on the water and test. Of the unit still leaks, replace the cartridge (E). Water flows from the tub spout while using the shower. The seal inside of the diverter mechanism may have become dislodged. The spout (H) may need replacement. Make sure that both hot and cold water inlets are turned on. Water flow is very low. Check the cartridge assembly (D), for debris. Sediment where the water enters the shower head (G) can also cause this symptom.
CONTROL PARTS INFORMATION FOR STEAM SHOWER FOR ALL UNITS 1. Steam Temperature Sensor 2. LCD Display 3. Control Panel 4. Water Diverter 5. Water Flow Adjustment (On/Off) 6. Water Temperature Adjustment 7. Body Jets 8. Steam Outlet 9. Handheld Shower Set 10. Steam Generator Cleaning Liquid Inlet LCD DISPLAY: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14.
CONTROL PANEL FOR STEAM SHOWER: CONTROL PROCEDURES Power on/off Push any button to light the display, and press the power on/off switch to start the system. Push the power on/off switch again to turn off the system and display. Steam Temperature Setting Touch the Steam Temperature Setting button and the display will appear on the screen. The temperature ranges from 20°C to 59°C circularly. Let go of the button when the desired temperature has been reached, and the figure is set as a steam setting.
Chromatherapy This button controls the color of the Chromatherapy LED lights (picture 5). When the Chromatherapy function starts, the lamp symbol on the LCD display flashes. Circulation Fan This button turns fan on/off. When fan is turned on, the fan symbol on the LCD display Flashes. Steam on/off This button turns the steam on/off. Touching this button makes the steam symbol on the LCD display flash. The temperature sensor regulates steam output based on the preset steam temperature.
WIRELESS FM TRANSMITTER On/Off: Push and hold this button for power on/off. Push and release this button shortly to change between transmitting and clock. Audio signal input: to be connected to audio signal output interface of Mp3 player. Transmitting frequency +/- adjusting: push this button to increase/decrease for transmitting frequency for FM. The adjusting range is 88-108.8MHz.
TROUBLESHOOTING FOR STEAM CABIN ISSUE Touch panel does not work CAUSE 1. Not connected properly 2. Wrong voltage No steam Steam generator keeps adding water Power supply is off when on/off button is pushed SOLUTION Check connection between control panel and power box 1. Desired steam room temperature is lower than current temperature Change to 220V supply Increase the desired temperature to be higher than current temperature 2.
| P a g e Rev1/2015
