Installation Sheet

ManualsBrandsSteamist ManualsSteam Shower Systems and ControlsSteamist 250 Round Digital Shower Control

Important: Locate Publication No. 199 “Steam Bath Important Safety Instructions”. This publication includes a Warning

label that the contractor must install on the wall near the entrance to the steam room in a highly visible location. This

label and its additional safety information are packaged with the generator in the envelope containing the installation

instructions. If it is lost or missing contact Steamist (201-933-0700) for a replacement Publication No. 199. This publica-

tion along with all documents must be left with the owner.

Installation & Operating Instructions

03/17

Pub. No. 271-E

- 1 -

Steambath Control Models: TSC-250 & TSC-250R

Control Features

( *New for 2017 )

1. Display: The digital readout displays the ambient temperature,

set point and cycle time, system status, and diagnostic error

codes.

2. Steam Icon: When illuminated the steam cycle is running.

3. Water Icon: When steam shower is not in use the blue water

icon indicates the **InstaMist feature is on. This is also illumi-

nated during a steam bath cycle.

4. Menu button: Used to change cycle time, turn **InstaMist on or

off and switch between ºF and ºC. When steam is off, pressing

this button will toggle between these settings. The settings are

changed with the up/down arrow buttons.

5. Stop button: Pressing this button stops the current steam cycle

and the Menu mode.

6. User 1 button: Starts the user one cycle and is the up function

when changing Menu settings. Pressing this button while in a

cycle will change the temperature and remaining time left on

that cycle.

7. User 2 button: Starts the user two cycle and is the down

function when changing Menu settings. Pressing this button

while in a cycle will change the temperature and remaining time

left on that cycle.

IMPORTANT: This control must be installed inside the steam room

for proper operation of the system and will ONLY function with TSG

and SMP model steam generators.

Cleaning Instructions: Use a damp cloth and mild soap. Do

NOT use abrasive cleaners which might scratch the surface

or the base of the control.

*If your model TSC-250 control does not match the picture

below, please see Pub. No. 271-D.

**InstaMist option is ONLY available when connecting to a

“TSG” model steam generator (InstaMist function is not

available on the “SMP” models). InstaMist is a preheat

function that keeps the water heated for quick starts.

TSC-250 Digital Temperature Control

TSC-250 Digital Temperature Control ( 2017 Model )

STOP

TSC-250R (Round control)

STOP

Summary of content (4 pages)

PAGE 1
Installation & Operating Instructions ® C Steambath Control ! ® US Models: TSC-250 & TSC-250R Important: Locate Publication No. 199 “Steam Bath Important Safety Instructions”. This publication includes a Warning label that the contractor must install on the wall near the entrance to the steam room in a highly visible location. This label and its additional safety information are packaged with the generator in the envelope containing the installation instructions.
PAGE 2
Installation & Operating Instructions Installation Instructions 1. Pre-Installation - Control Location a) The TSC-250 Control must be installed inside the steam room. For convenience the recommended height from the floor is four feet. Provide a 1½" hole in the wall at this location (see Figure 1). IMPORTANT: Multi-conductor cable must be installed so that the end will not be buried inside the wall. The unit will not operate unless the control is installed. 2.
PAGE 3
Installation & Operating Instructions Operating Instructions Operation: Make sure the water and power are turned on. Simply press USER 1 or USER 2 button to begin the cycle. Press the Stop button will end the cycle. After a cycle is started it will take a few minutes for the Steam Generator to heat up and begin producing steam. This time will be less if the InstaMist has been ON. During operation the display will show the ambient temperature.To view the remaining cycle time, press the Menu button.
PAGE 4
Installation & Operating Instructions Figure 4 - Installation Suggestions TSX-220 Auxilary Outside Control MENU __ __ __ __ 1 2 1 2 1 2 STOP X X TSC-250 must be mounted inside the steamroom. Locate away from the direct line of shower spray and do NOT locate above steamhead.