Important information Warning! In case of any discomfort or adverse reactions, including dyspnea, irritation of eyes, nose, throat or buttock, please leave the room immediately and see a doctor. Notice: Please post the above warning on the conspicuous position of the steam room. Warnings: Do not use water-soluble perfume or emulsifier and acetaldehyde containing perfume. The above solution may cause damage to this machine.
Double pump Single pump Figure 2: Configuration Diagram 1. Pump A 2. Pump A switch 3. Mounting plate 4. Aroma oil controller 5. Housing 6. Pump B switch 7. Pump B 8. Aroma oil container 9. Control line 10. Pump B inlet 11. Pump B outlet 12. Pump A inlet 13. Pump A outlet 14. Power line 15.
5. The aroma diffuser should not be installed a place where is close to flammable materials, materials with corrosive properties and chemicals. 6. The installation of aroma system should be easy to operate, and enough space should be left for maintenance and injecting aroma oil. 7. The system should be installed in a place where is not easy for children to touch, and you'd better install it in a special isolation room 8.
Installation of pneumatic switch button (only for single pump SS-SAP001-XX) 1. Open a ￠ 32 hole on the steam room wall with a height of about 1.5m, which is easy to operate. 2. Install the pneumatic switch button as shown in Figure 4. 3. Connect the other end of hose to the pneumatic switch interface on the aroma diffuser as shown in Figure 2 and Figure 7. It is best to add a little glue to the hose and interface. 4.
Installation of double pump SS-DAP001-XX/ single pump SS-SAP001-XX: When use the SS-BCT01BK control panel, you can connect the control line of the aroma pump with the control line from the sound box of SS-BCT01BK. We should install the aroma pump as the following steps: Installation of double pump SS-DAP001-XX: 1. First, the aroma pump should be fixed on the wall. 2. Second, install 3/4" three-way valve on the steam pipe. 3.
Figure 6 Installation Drawing of double pump SS-DAP001-XX Aroma Pump 1. Steam engine 2. Control line of aroma diffuser 3. Aroma diffuser 4. Sauna lamp 5. Fan 6. Temperature probe 7. SS-BCT01BK controller 8. Steam jet 9. Aroma oil injection port 10. Steam pipe 11. Drainage pipe 12. Bluetooth sound box 13. Temperature controlled switch Figure 7 Installation Drawing of Single Pump SS-SAP001-XX Aroma Pump 1. Steam engine 2. Control line of aroma diffuser 3. Aroma diffuser 4. Sauna lamp 5. Fan 6.
Operation of double pump SS-DAP001-XX/ single pump SS-SAP001-XX: Characteristic: Such two pumps can be respectively configured to open and close, and such state can be saved by memory in case of power failure.
Operation 1. Touch ON/OFF to open and close corresponding aroma pumps A and B; When open, the corresponding digital display window will be displayed while close, the display window will be turned off. 2. Standby mode: After pump A\B opens, if the temperature switch and button switch are not closed, it will be in standby mode, and the aroma pump will not operate, the display window will display "- -". 3. Opening countdown: After closing the switch of the aroma pump, if the pump A\B is open, the green indicat
Technical data and figure Power supply: 110V-240V 50/60HZ Motor voltage: 11VDC Power: ≤10W Inspection and repair of failure Warnings: To avoid any injury caused by electric shock, unplug the power plug before the repair. 1. The controller fails to display: Check whether the switching power supply is powered by power supply and whether the output voltage is normal. In case of damage of switching power supply, please contact your dealer or manufacturer. 2.
