Owner's manual

ManualsBrandsSteelcraft Automotive ManualsFor the car440709p 5 PREMIUM OVAL SIDE BAR

5” OVAL BENT END SIDEBAR

04-12 NISSAN TITAN CREW CAB

Page 1 of 2 07/13/12 (DP)

PARTS LIST:

Driver/Left Sidebar

8-1.25mm x 25mm Hex Bolts

Passenger/Right Sidebar

8mm Lock Washers

Driver/Left Mounting Brackets

8mm x 24mm OD x 2mm STD Flat Washers

Passenger/Right Mounting Brackets

8mm x 16mm OD x 1.6mm Small Flat Washers

8-1.25mm x 30mm Hex Bolts

8mm Nylon Lock Nuts

PROCEDURE:

1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS

CAREFULLY BEFORE STARTING INSTALLATION.

2. Start installation at the front of the driver side of the vehicle and locate the factory threaded stud and

the threaded hole located on the side of the inner body panel, (Figure 1). NOTE: Remove the plastic

plug or any insulation on the side panel to locate the threaded holes.

3. Select (1) driver side Mounting Bracket. Attach the Bracket to the threaded stud with (1) 8mm x 24mm

STD Flat Washer and (1) 8mm Nylon Lock Nut. Next, insert (1) 8mm x 30mm Hex Bolt with (1) 8mm

Lock Washer and (1) 8mm x 16mm Small Flat Washer through the remaining lower hole in the Bracket

and into the threaded hole, (Figure 2). Snug but do not tighten hardware at this time.

4. Repeat Steps 2 – 3 to install the center and rear Mounting Brackets, (Figures 2 – 4). NOTE: The

cradles on the Mounting Brackets should be facing the rear of the vehicle when properly installed.

5. Once all three Mounting Brackets are partially installed, carefully place the driver Sidebar onto the

Mounting Brackets. Use the included (6) 8mmx 25mm Hex Bolts, (6) 8mm Lock Washers and (6) 8mm

x 24mm STD Flat Washers to bolt the Sidebar to Mounting Brackets, (Figures 3 & 4).

6. Level and adjust the Sidebar and tighten all hardware at this time.

7. Repeat Steps 2 – 6 for passenger Sidebar installation.

8. Do periodic inspections of the installation to make sure that all hardware is secure and tight.

To protect your investment, wax this product after installing. Regular waxing is recommended to add a protective layer

over the finish. Do not use any type of polish or wax that may contain abrasives that could damage the finish.

For stainless steel: Aluminum polish may be used to polish small scratches and scuffs on the finish. Mild soap may be

used also to clean the Sidebar.

For gloss black finishes: Mild soap may be used to clean the Sidebar.

Driver/Left Side

Mounting Brackets

Passenger/Right Side

Mounting Brackets

Front of

Vehicle

Front of

Vehicle

Insert locations

for brackets

Front of

Vehicle

Summary of content (2 pages)

PAGE 1
5” OVAL BENT END SIDEBAR 04-12 NISSAN TITAN CREW CAB PARTS LIST: 1 1 3 3 6 Driver/Left Sidebar Passenger/Right Sidebar Driver/Left Mounting Brackets Passenger/Right Mounting Brackets 8-1.25mm x 30mm Hex Bolts Passenger/Right Side Mounting Brackets 12 18 18 6 6 8-1.25mm x 25mm Hex Bolts 8mm Lock Washers 8mm x 24mm OD x 2mm STD Flat Washers 8mm x 16mm OD x 1.
PAGE 2
5” OVAL BENT END SIDEBAR 04-12 NISSAN TITAN CREW CAB Driver Side Installation Pictured Threaded Stud Front 8mm x 30mm Hex Bolt 8mm Lock Washer 8mm x 16mm Small Flat Washer 8mm Nylon Lock Nut 8mm x 24mm STD Flat Washer Threaded Hole (Fig 1) Driver side rear mounting location pictured.