Manual

Owner's Manual
MAINTENANACE
WARNING! When servicing, use only replacement parts recommended by the']
manufacturer of this tool. Use of any other parts may create a hazard or cause[
..... pr°duci,,damage J
WARNING! Always wear safety goggles or safety glasses with side shields "_
during power tool operation or when blowing dust. If operation is dusty, also
J
wear a dust mask.
WARNING! Before performing any maintenance, make sure the tool is un- |
plugged from the power supply and the switch is in the "OFF" position. Failure
J
to heed this warning could result in serious personal injury.
CARBON BRUSHES
See Fig. 19.
The brushes and commutator in your
tool have been engineered for many
hours of dependable service• To main-
tain peak efficiency of the motor, we
recommend every two to six months
the brushes be examined•
Motor Brush Replacement
To inspect or replace brushes:
Unplug the saw.
Fig.19
WARNING! The brush cap is spring loaded by the brush assembl_ J
J
2. Remove the brush cap on the motor using a wide flat blade screwdriver•
3. Pull out the brush• Repeat for the opposite side.
NOTE: If installing the existing brush or brushes, make sure the brush goes
in the same way it came out. Otherwise a break-in period will occur that will
reduce motor performance and increase brush wear•
4. Inspect the brushes for wear. On the wide flat side of the brush is a wear
iimit }ine. If the brush contact face is at or beyond (no iine visible) the iimit
replace brushes as a set.
5. Install the new brush• The two tabs on the brush terminai go in the same
hole the carbon part fits into.
6. Tighten the brush cap but do not overtighten.
Exploded view
8_er's Manua!
iit
MAINTENANCE
0_er's Manual
GENERAL MAINTENANCE
1. Periodically check all clamps, nuts, bolts, and screws for tightness and con-
dition. Make sure the table insert is in good condition and in position•
2. Check the blade guard assembly.
3. Clean your cutting tools with a gum and pitch remover•
4. To maintain the table surfaces, periodically apply paste wax to them and buff
to provide smooth functioning• To prevent work from slipping during cutting
operations, DO NOT wax the working face of the miter gauge•
5. Protect the saw blade by c}eaning out sawdust from underneath the saw
table and in the blade teeth• Use a resin solvent on the blade teeth•
6. Clean plastic parts only with a soft damp cioth. DO NOT use any aerosol or
petroleum solvents.
WARNING! Do not at any time let brake fluids, gasoline petroleum-based
products, penetrating oils, etc., come in contact with the plastic parts. Chemi-
J
cals can damage, weaken or destroy plastic which may result in serious
personal injury.
LUBRICATION
This saw's motor bearings have been packed at the factory with proper iubrica-
tion.
1. C}ean the screw threads and nuts with a solvent recommended for gum and
pitch removal
2. Lubricate the screw threads, nuts and bearing points (including those on the
blade guard assembly and miter gauge)•
PUEASE READ THE FOLUIOWING CAREFULLIIY
The manufacturer and/or distributor has provided the parts list and assembly
diagram in this manual as a reference tool oniy. Neither the manufacturer or dis-
tributor makes any representation or warranty of any kind to the buyer that he or
she is qualified to make any repairs to the product, or that he or she is qualified
to replace any parts of the product. In fact, the manufacturer and/or distributor
expressly states that all repairs and parts replacements should be undertaken
by certified and licensed technicians, and not by the buyer. The buyer assumes
all risk and liability arising out of his or her repairs to the original product or
replacement parts thereto, or arising out of his or her instailation of replacement
parts thereto.
8wner's Manual
P_'ls _sting
APA Parts No. No. Description OTY APA Parts No. No. Description OTY
PBl13-31-ZY 31 SCREW (M5X23) 1 PBl13-4B-ZY 46 SWITCH 1
PBl13-32-ZY 32 SOCKETHEADSCREWMBX13 1 PBl13-47-ZY 47 CAPACITANCEB.33UF 1
PBl13-33-ZY 03 BIGWASNER 1 PBl13-48-ZY 48 HANDLE4 1
PBl13-34-ZY 34 SCREWMBX13 1 PBl13-49-ZY 49 SELE-TAPHNGSCREWST4X14
PBl13-35-ZY 35 LOCATING PLATE 1 PBl13-53-ZY 50 BRUSH HOLDER CAP 2
PBl13-36-ZY 36 SPRING 1 PBl13-51-ZY 51 CARBON BRUSH 2
PBl13-37-ZY 37 WASHER 1 PBl13-52-ZY 52 BRUSH HOLDER
J
PBl13-38-ZY 08 GUARDCOVER 1 PBl13-53-ZY 53 HOUSE 1
PBl13-39-ZY 39 PRESSBOARDSCREW M8X16-L 1 PBl13-54-ZY 54 SCREWM6X33
PBl13-1O-ZY 13 UPPER PRESSBOARD 1 PBl13-55-ZY 55 PLANEWARHER 4
PBl13-11-ZY 11 SAWBLADE 1 PBl13-56-ZY 56 SCREWM3X12 1
PBl13-12-ZY 12 LOWERPRERSBOARD 1 PBl13-57-ZY 57 HANDLEOFBENDEDARM ]
PBl13-13-ZY 13 SCREW MBX12 2 PBl13-SB-ZY 58 SCREW 1
PBii3-14-ZY 14 BEARiNG PRESSBOARD 1 PBii3-59-ZY 59 SHAFT
PBl13-15-ZY 15 OBTPUTSPINDLE 1 PBl13-B3-ZY 60 O-RING¢6.7X¢I.8 1
PBl13-16-ZY 16 WOODRBFFKEY 1 PBl13-61-ZY 61 LOCKINGSHAFTKNOB 1
PBl13-17-ZY 17 BEAR[NG6203 1 PBl13-62-ZY 62 BENDEDARM
PBl13-18-ZY 18 GEARBOXCOVER 1 PBl13-63-ZY 63 SCREWMBX33 3
PBl13-19-ZY 19 BIGGEAR 1 PBl13-64-ZY 64 NUTM6 1
PBl13-2O-ZY 23 C[RCLIPFORSHAFT¢17 1 PBl13-B5-ZY 65 BENDEDARM FINGER ']
PBl13-21-ZY 21 SCREWM4X13 2 PBl13-BB-ZY 66 SCREWM3X8 1
PBl13-22-ZY 22 SLIDINGBEARING 1 PBl13-67-ZY 67 BASEOFBENDEDARM
PBl13-23-ZY 23 BIGSPRING 1 PBl13-Bg-zY 68 SCREWM12X21 2
PBl13-24-ZY 24 STRETOHINGSCREW 1 PBl13-69-ZY 69 SOCKETHEADSCREWMBX33 2
PBl13-25-ZY 25 SAWCOVER "T PBl13-73-ZY '_ BACKBOARD ']
PBl13-26-ZY 26 LOOKNUTM6 1 PBl13-71-ZY 71 SBNKSCREWM4X13 5
PBl13-27-ZY 27 CONTROLKNOB "T PBl13-72-ZY _ PROTBCTIVEBOARDFORSAWBLADE']
PBl13-BS-ZY 28 SPRING 1 PBl13-73-ZY 73 SWlVELTABLE 1
PBl13-BS-ZY 29 SCREW 1 PBl13-74-ZY 74 SCREW 1
PBl13-3O-ZY 33 CONTROLKNOB SEAT 1 PBl13-75-ZY 75 FINGER ]
PBl13-31-ZY 31 SOREWMSX14 2 PBl13-7B-ZY 76 BASE 1
PBii3-32-ZY 32 BEARiNG 6201 '_ PBii3-77-ZY 7 FOUNDATION 6
PBl13-33-ZY 33 SCREWM4X13 1 PBl13-78-ZY 78 LOCKNUTM6
PBl13-34-ZY 34 SELFT-LOCKINGPRESSBOARD 1 PBl13-79-ZY 79 STRETCH[NGSCREWMBX23 1
PBl13-35-ZY 35 SPRING 1 PBl13-B3-ZY 80 SPINDLE
PBl13-36-ZY 36 SELF-LOCKING POLE 1 PBl13-B1-ZY 81 SCREW&COVER 2
PBl13-S7-ZY 37 ROTOR 1 PBl13-32-ZY 82 HANDSPIKE 1
PBl13-38-ZY 38 BEARINGS29 1 PBl13-B3-ZY 83 BATTERYCOVER
P3113 -39-ZY 39 BEARING COVER 1 P3113 -84-ZY
P3113 -4O-ZY 43 STATOR 1
P3113 -41-ZY 41 HANDLE 1 1
P3113 -42-ZY 42 HANDLE 2 1
84 LASER 1
P3113 -85-ZY 85 LASER HOLDER
P3113 -86-ZY 86 BATTERY COVER SCREW 2
P3113 -37-ZY 87 CABLEJACKET 1
PBl13-43-ZY 43 SELF-TAPPINGSCREWST4X2O 8 PBl13-BB-ZY 88 CABLE
PBl13-44-ZY 44 SELF-TAPPINGSCREWST4X2O 3 PBl13-B9-ZY 89 OABLEPRESSBOARD 1
Z i _ Z_ROREW _