Owner's Manual SE 3400 PSI Pressure Washer WARNING! To Reduce The Risk Of injury, User Must Read And Understand Instruction Manual SP-WG340 I cE CALL BRR-296-6881 www
former's Manual Tahoe Of Contents Topic Page Warranty 3 Safety Guidelines-Definitions 4 General Precautions 5 Safety Precautions 7 Pr-Start Nonrepresentational 8 Operation 8 Detergent Connection 1 Maintenance 13 Trouble Shooting 18 Parts Break Down 17 A WARNING! READ AND UNDERSTAND ALL SAFETY PRECAUTIONS IN THIS MANUAL BEFORE OPERATING. FAILURE TO COMPLY WITH INSTRUCTIONS IN THIS MANUAL COULD RESULT iN PERSONAL INJURY, PROPERTY DAMAGE, AND/ OR VOIDING OF YOUR WARRANTY.
former's Manual Limited Warranty Steele® warrants 10 the original purchaser who uses the product in a consumer application (personal, residential or household usage) that all products covered under this warranty are free from defects in material and workmanship for ane year from the date of purchase. All products covered by this limited warranty which ara used in commercial applications (i.e.
Buber's Manual Safety Guidelines-Definitions A WARNING! Read and understand all safely precautions in this manual before operating. Failure to comply with instructions in this manual could result in personal injury, property damage, and / of voiding of your warranty, Steele@ will not be Hale for any damage because of failure fo follow these instructions. SAFETY SYMBOLS The following symbols are used throughout this manual.
former's Manual General Precautions PRESSURE WASHER The following safely precautions apply whenever using, storing, of servicing your pressure washer io reduce the possibility of personal injury, Overlooking or ignoring these precautions can lead to personal injury or product damage. a ea » Read this manual carefully. Know your equipment. Consider applications, potential hazards and limitations for your unit. « This equipment is designed for specific applications.
former's Manual General Precautions « Keep the pressure washer clean and free of olf, mud and other foreign matter, « Do not wear loose clothing. jewelry. or anything that may be caught in the engine. » Never direct spray ai people or animals. = Never allow children to operate pressure washer at any time + Use hath hands to control the wand. « Do not touch the nozzle or water spray while operating. » Wear safety goggles while operating. » Only approved hoses and nozzles should be used.
Buber's Manual General Precautions « Do not touch hot muffler, « Service, operate and refuel under the following conditions: a. Good ventilation Db. Refuse! the pressure washer in a well iif area. ¢. Avoid fuel spills and never refuel while the pressure washer is running. 4. Avoid any ignition source when refueling 8. Use lead free fuse with a minimum of 85 octane. » Do not smoke near pressure washer.
former's Manual Pr-Start Nonrepresentational BEFORE OPERATION NOTE: The engine and pump on your pressure washer will often have improved performance afire a break-in period of several hours, PROPRIETARY PREPARATION Before starting the pressure washer, check for loose or missing parts and for any damage which may have ace tired during shipping ASSEMBLY & START-UP HBase & Gun Assembly NOTE: Align threaded connections carefully fo prevent damaging threads during assembly.
former's Manual Operation OPERATING CONNECTIONS High Pressure Hosea » Attach the high pressure hose fo the pressure washer by pulling back on the collar of the Buick-connect coupling on the hose and pushing i over the coupling half on the pressure washer outlet NOTE: Do not use pressure hose from another manufacturer, WATER CONNECTION Before connecting the garden hose to your pressure washer, run water through the garden hose {not supplied) to flush out any foreign matter.
former's Manual Operation OPERATING INSTRUCTIONS Starr-up Procedure 1. Make sure water supply is connected and turned on. 2. Release gun safety if locked. 3. To allow air to escape from the hose, squeeze trier on the gun until there is a steady flow of water coming out from the nozzle Starting Engine 1. Check ofl and gas. 2. Conn act hose and turn on water, 3. Squeeze trigger 4. Make sure the pressure washer is on the ON position {illustration 1). 5. Set the fuel naive to open (illustration 2). 6.
Buber's Manual Detergent Conn action CAUTION! This pressure washer is intended for use only with liquid car wash detergents, developed specifically for pressure washers and with mild saps. Only use chemicals compatible with the aluminum and brass pails, Powdered soaps may clog the injection system. Always use chemicals according to the manufacturers directions. We assume no responsibility for any damages caused by chemicals injected through this pressure washer, 1.
former's Manual Detergent Conn action/ Usage OPERATION Av aid working on hot surfaces of in direct sunlight 10 minimize the chances of the chemical damaging painted surfaces. Damage may occur to painted surfaces If the chemical is allowed fo dry on the surface. Hold the nozzle far enough away from surface fo prevent damage {o the surface. 2. Allow chemical to remain on the surface for a short time before rinsing. 3. Rinse with clean water under high pressure.
former's Manual Maintenance MAINTENANCE 2. Clear the nozzle with a small rigid piece of wire such as a paper clip 3. Flush the nozzle backwards with water. 4. Reconnect the wand to the gun. Restart the pressure washer and depress the trigger on the spray gun. If the nozzle is still plugged or partially plugged, repeat above instructions 1-4, if the previous procedure does nat clear the nozzle, replace with a new nozzle.
former's Manual Maintenance Another method of reducing risks of freeze damage is fo drain your pressure washer as follows: 1. Stop the pressure washer and detach supply hose and high pressure hose. Squeeze the trigger of the di rge gun fo drain all water from the wand and hose. 2. Restart the pressure washer and fat it run briefly about 5 seconds) until water no longer discharges from the high pressure outlet.
former's Manual Trouble Shooting = Engine wil not start of stops while operating Low-oil shutdown: Engine switch not in “ON” position: Pressure built up in hos: = Engine is overloaded Nozzle partially blocked Excessive precise « Pressure increases when gun is locked Bypass valve blocking Fill engine with oil Turn switch “ONS Syracuse trigger while starting Clean Nozzle Shorten the spring coil on the reflex naive Clean the bypass valve + Engine is running but pump won't bulls maximum pressure or has irregula
former's Manual Trouble Shooting = Water In crankcase High humidity Worn seals « Noisy operation Worn bearings Aly mixed with water = Laugh / pulsating, aerating with pressure rap Inst restriction Unloaded Ar mix in water + High crankcase temperatures Wang grade of oil Improper amount of oil in crankcase Change vil more frequently Change the oil seals Change the bearings Check inlet lines for restrictions and / of proper sizing Check system for stoppages, air leaks, correctly sized inlet plumbing to pump Ch
Parts Break Down 1 Hub 2ap 2 Bump senility 3 Nacho cover 4 Retaliatory wire drawing 5 Component of accelerator pontoon lever 6 Eng 7 simulator 8 Carriage & hud 10 Plans 1 Boy 12 Rubin fat 13 Wheel 4 Polemics hose 15 Hose scepter 15 Sower 17 Vile ror cape former's Manual 18 Handle 19 Grommet 20 Hox Nut 21 Clamp: 2 0 fh pine cap 23 Bok 24 Nut 2 Vip Hose 28 Muse 27 Guy west.
