Installation and Safety Instructions

INSTALLATION AND SAFETY INSTRUCTIONS
FOR YOUR SAFETY WARNING
BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING
ON IS SHUT OFF; EITHER THE FUSE IS REMOVED OR THE
CIRCUIT BREAKER IS SHUT OFF. GENERAL You don’t need special
tools to install this fixture. Be sure to follow the steps in the order given.
Under no circumstances should a fixture be hung on house electrical
wires, nor should a swag type fixture be installed on a ceiling which
contains a radiant type heating system. Read instructions carefully. If
you are unclear as to how to proceed, consult a qualified electrician.
NOTE: Proper wiring is essential for the safe operation of this fixture.
GENERAL
You don’t need special tools to install this fixture. Be sure to follow the
steps in the order given. Under no circumstances should a fixture be
hung on house electrical wires, nor should a swag type fixture be
installed on a ceiling which contains a radiant type heating system.
Read instructions carefully. If you are unclear as to how to proceed,
consult a qualified electrician. NOTE: Proper wiring is essential for the
safe operation of this fixture.
FIXTURE ASSEMBLY
Carefully remove the fixture from the carton and check that all parts
are included as shown in figure. Be careful not to misplace any of the
screws or parts, which are needed to install this fixture.
STEP 1: Thread end of the stem (M) into nipple (N) and other end of
the stem (M) into coupling (L).
STEP 2: Place the arms (P) for end of the bend hole is aligned with the
hole on the inside of the steel ring (Q) and secure with the
ball screw (O),the place the arms (P) other end of the hole is
aligned with the hole on the outside of the steel box (K)
and secure with the ball screw (O).
INSTALLATION
IMPORTANT: Do not attach fixture directly to outlet box.
STEP 1: Secure cross bar (A) to outlet box with outlet box screws
(B).Thread nut (D) onto nipple (E). Insert lock washer (C) and
thread the nipple (E) onto mounting bar (A), then secure
with the nut (D).
STEP 2: Thread screw collar ring (G) onto nipple (E). Slide screw
collar ring (G) and canopy (F) over screw collar ring (G).
Using a pair of pliers, open the chain link (H) and chain link
(J) connect it to collar ring (G),chain (I) and fixture loop
(K),Close the chain link (H) & (J).
BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY.
STEP 3:Lace wires up through chain (H) and pass wires through
holes in screw collar ring (G),We recommend lacing wire
up through every other link of chain (I).
GROUNDING INSTRUCTIONS
STEP 1: Insert the green grounding screw into the hole with two raised
dimples on the mounting bar. Wrap the ground wire from the
fixture (if supplied) around the green grounding screw, then
connect it to ground wire from the outlet box (if not fixed on
the outlet box) using a wire connector (not supplied). If
ground wire from the fixture is not supplied, wrap the ground
wire (if not fixed on the outlet box) from the outlet box around
the green grounding screw and tighten it.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER
SUPPLY WIRES.
STEP 2: Take note of the color of the wire(s) on your fixture.
Identify which group your fixture wire(s) falls into and connect
the wires according to the directions below:
GROUP A: Connect to Black
House Wire
GROUP B: Connect to White
House Wire
BLACK
WHITE
*PARALLEL WIRE (round &
smooth)
*PARALLEL WIRE (square &
ridged)
WHITE OR GREY WITH
TRACER
WHITE OR GREY WITHOUT
TRACER
BROWN GOLD OR BLACK
WITHOUT TRACER
BROWN, GOLD OR BLACK
WITH TRACER
*NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer
wire is square shaped or ridged and the less tracer wire is
round in shape or smooth (seen best when viewed from
wire end.)
STEP 3:Take your fixture wire(s) from group A and place evenly
against the black wire from the outlet box. Do NOT
twist wires together before using wire connectors.
STEP 4:Fit a wire connector (not supplied) over the wires and
screw the connector clockwise until you feel firmness.
STEP 5:Try gently to pull the connector off the wires. If you can
pull the connector off, carefully re-do steps 3 and 4 as
above, and check again for a firm connection.
STEP 6: Connect the fixture wire from group B to the white wire
from the outlet box in the same manner. Make sure no
bare wires can be seen outside wire connectors.
FINAL ASSEMBLY
STEP 1: After wires are connected, tuck them carefully inside outlet
box. Raise canopy (F) allowing for nipple (E) to protrude
through the holes on canopy (F), and secure with screw
collar ring (G).
STEP 2: Install light bulbs. (Please do not exceed the maximum
capacity recommended on the socket.)
CLEANING
To clean, wipe fixture with a soft cloth. Clean glass with a mild
soap. Do not use abrasive materials such as scouring pads or
powders, steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Be sure to use exact wording from illustration
when ordering parts.
Line art shown may not exactly match the fixture enclosed.
However, the installations do apply to this fixture.