Remote Control Devices

19
Remote controlling Cubase
Yamaha 01V
The Yamaha 01V can remote control Cubase. Before you
can initiate remote control operation, the 01V must be set
up in the following way:
• MIDI Parameter Change and Receive must be enabled.
• MIDI Control Change and Receive must be disabled.
• Device ID / MIDI Channel Receive must be set to “1”.
• Local Control should be set to “Off”.
As soon as Local Control is set to “Off”, remote control is enabled.
The 01V remote operation of Cubase is very straightfor-
ward, with (almost) every parameter having the equivalent
parameter controller in the 01V mixer. The current status
of all controllable parameters is fed back to the 01V and
indicated on the panel, using the motorized faders, indica-
tors, etc. (for this to work, you need a two-way MIDI con-
nection between the 01V and Cubase).
To facilitate 32 channel remote control, two separate con-
trol “Layouts” are used, each controlling 16 mixer chan-
nels. The “Memory” button on the 01V is used to switch
between VST layout 1 and 2. Page 1 displays VST Layout
1, and page 2 VST Layout 2.
The following parameters are remote controllable for
channels 1–32 in the mixer:
• Fader level, mute and pan.
01V controls for these parameters control the equivalent Cubase param-
eters.
• Effect sends 1–6.
01V Aux 1–4 control effect send 1–4, 01V effect 1 and 2 control effect
send 5 and 6.
• EQ Frequency, Gain and Q (4 bands).
01V controls for these parameters control the equivalent Cubase param-
eters.
• Stereo Master Volume.
The 01V control for this parameter controls the equivalent Cubase pa-
rameter.
• Send effects master volume 1–4 are controlled by 01V
Aux Master 1–4. Send effects master 5 and 6 are con-
trolled by 01V effect master 1 and 2.
With Layout 1 the 01V controls the following channels:
• Channel 1–12, 13/14 and 15/16 will control channels
1–14.
• 01V Return 1 and 2 will control channels 15 and 16.
With Layout 2 the 01V controls the following channels:
• Channel 1–12, 13/14 and 15/16 will control channels
17–30.
• 01V Return 1 and 2 will control channels 31 and 32.
Yamaha DM2000/DM 2000v2
The Yamaha DM2000 is a digital mixing console that pro-
vides full automation of virtually all console parameters. It
is designed to integrate effectively with digital audio work-
stations such as Cubase.
• For detailed information about features, parameters,
etc., please see the documentation which comes with the
Yamaha DM2000.
In this version of Cubase, the following functions have
been added:
Automix Section
• [Auto]: write enable
• [Set] + [Auto]: read enable
• Studio 1–4 added as [Aux9]–[Aux12] to the DM2000 -
Operation is identical to Sends (volume, on/off, pre/post
supported)
• Matrix [Aux9]–[Aux12] will assign Studio 1–4 to the en-
coders above the faders
• Selected Channel Aux9–12 will assign Studio 1–4
!
The value ranges for the parameters in the 01V may
not match the ranges for the corresponding parame-
ters in all cases.
User defined
keys
DM 2000 Button Cubase function
#3 Abort Drop out mode Touch
#4 Auto rec Drop out mode Latch
#5 Return Drop out mode X-Over
#6 Relative Trim mode
#7 Touch sense Toggle Write Enable All Tracks