Instructions

– 12 – – 13 –
Safety warnings

Disconnect the power
before attempting any
work on the motion
detector.

The electrical connec-
tion lead must be dead
during installation.
Therefore, switch off the
power supply fi rst and
check that the circuit is
disconnected using a
voltage tester.
 Installation of the sensor
involves work on the
mains power supply.
This work must therefore
be carried out profes-
sionally in accordance
with the applicable wiring
regulations and supply
conditions.

Please note that the sen-
sor must be protected
by a 10 A circuit breaker.
The mains supply lead
must be no greater than
10 mm in diameter.

Only carry out time and
light threshold settings
with the lens fi tted.
Principle
The IS 180-2 is equipped
with two 120° pyro sensors
which detect the invisible
heat emitted by moving
objects (people, animals
etc.). The heat detected
is electronically converted
into a signal that switches
on loads (e.g. a light) con-
nected to it. Heat is not
detected through obstacles,
such as walls or panes of
glass. Heat radiation of this
type will, therefore, not trig-
ger the sensor. With a 90°
angle of aperture, the two
pyro sensors cover a detec-
tion angle of 180°. The lens
can be removed and turned,
thereby permitting two max.
basic reach settings of 5m
or 12 m. Using the wall
mounts provided with the
unit, the infrared sensor can
easily be fi tted to internal
and external corners.
Important: The most
reliable way of detecting
motion is to install the unit
so that the sensor is aimed
across the direction in
which a person would walk
and by ensuring that no
obstacles (such as trees,
walls etc.) obstruct the line
of sensor vision.
Reach max. 12 m Reach max. 5 m
Direction of approach:
towards the sensor
Direction of approach:
across the detection zone
GB Installation instructions
Dear Customer,
Congratulations on purchas-
ing this STEINEL Infrared
Sensor and thank you for
the confi dence you have
shown in us. You have cho-
sen a high-quality product
that has been manufac-
tured, tested and packed
with the greatest care.
Please familiarise yourself
with these instructions
before attempting to install
the sensor since prolonged
reliable and trouble-free op-
eration will only be ensured
if it is installed properly.
We hope your new Infrared
Sensor will give you lasting
satisfaction.
System components
 Security screw
 Front cover
 Lens (can be removed
and turned for selecting
the max. basic reach set-
tings of 5 m or 12 m)
 Light threshold setting
control 2 – 2000 lux
 Time setting control
5 sec. – 15 min.
 Clip (housing can be
fl ipped up for assembly
and connection to mains
power supply)
Technical specifi cations
Dimensions (H×W×D): 120×76×56 mm
Output: Incandescent / halogen lamp load
Fluorescent lamps, electronic ballast
Fluorescent lamps, uncorrected
Fluorescent lamps, series-corrected
Fluorescent lamps, parallel-corrected
Low-voltage halogen lamps
LED < 2 W
2 W < LED < 8 W
LED > 8 W
Capacitive load
Connection: 230-240 V, 50 Hz
Detection angle: 180° horizontal, 90° vertical
Sensor reach: basic setting 1: 5 m max.
basic setting 2: 12 m max. (factory setting)
+ precision adjustment from 1-12 m by means
of clip-on shrouds
Time setting: 5 sec. - 15 min. (factory setting: 5 sec.)
Light threshold: 2-2000 lux (factory setting: 2000 lux)
Enclosure: IP 54
Temperature range: -20°C to +50°C
1000 W
1000 W
500 VA
406 VA
406 VA
1000 VA
16 W
64 W
64 W
132 μF